SIS SS-ISO 6858-1985 Aircraft Ground support electrical supplies General requirements《航空器 地面支持电气供应物 一般要求》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

KS D ISO 7539-3-2003 Corrosion of metals and alloys－Stress corrosion testing－Part 3：Preparation and use of U-bend specimens《金属和合金的耐腐蚀性 应力腐蚀试验 第3部分 U型弯曲试样的制备和使用》.pdf

KS D ISO 7539-4-2003 Corrosion of metals and alloys－Stress corrosion testing－Part 4：Preparation and use of uniaxially loaded tension specimens《金属和合金的腐蚀 应力腐蚀试验 第4部分 单向载荷拉伸试样的制备和使用》.pdf

KS D ISO 7539-5-2009 Corrosion of metals and alloys－Stress corrosion testing－ Part 5：Preparation and use of C-ring specimens《金属和合金的腐蚀 应力腐蚀试验 第5部分 C 环形试样的制备和使用》.pdf

KS D ISO 7539-6-2009 Corrosion of metals and alloys－Stress corrosion testing－Part 6：Preparation and use of pre-cracked specimens《金属和合金的腐蚀 应力腐蚀试验 恒定负荷或恒定位移条件下试验用预破裂试样的制备和使用》.pdf

KS D ISO 7627-1-2012 Hardmetals－Chemical analysis by flame atomic absorption spectrometry－Part 1：General requirements《硬质合金 火焰原子吸收光谱法的化学分析 第1部分 通用要求》.pdf

KS D ISO 7668-2012 Anodizing of aluminium and its alloys-Measurement of specular reflectance and specular gloss of anodic oxidation coatings at angles of 20 45 60 or 85《铝和铝合金的阳极氧化涂.pdf

KS D ISO 7692-2002 Ferrotitanium－Determination of titanium content－Titrimetric method《钛铁 钛含量的测定 滴定法》.pdf

KS D ISO 7693-2002 Ferrotungsten－Determination of tungsten content－Cinchonine gravimetric method《钨铁 钨含量的测定 辛可宁(Cinchonine)重量分析法》.pdf

KS D ISO 795-2012 Aluminium and aluminium alloys－Determination of copper content －Oxalyldihydrazide photometric method《铝和铝合金 铜含量的测定 草酰二肼光度法》.pdf