SNI 04-6960-2003 Overhead lines - Requirements and tests for spacers《架空线 分隔器的要求和试验》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

SANS 1700-17-5-1996 Fasteners Part 17 Pins Section 5 Clevis pins with head《紧固件 第17部分：销 第5节：有头销轴》.pdf

SANS 1700-17-6-1998 Fasteners Part 17 Pins Section 6 Parallel pins with internal thread of unhardened steel and austenitic stainless steel《紧固件 第17部分：销 第6节：带内螺纹圆柱销，不淬硬钢和奥氏体不锈钢》.pdf

SANS 1700-17-7-1998 Fasteners Part 17 Pins Section 7 Parallel pins of hardened steel and martensitic stainless steel (Dowel pins)《紧固件 第17部分：销 第7节：圆柱销 淬硬钢和马氏体不锈钢》.pdf

SANS 1700-17-8-1998 Fasteners Part 17 Pins Section 8 Parallel pins with internal thread of hardened steel and martensitic stainless steel《紧固件 第17部分：销 第8节：内螺纹圆柱销 淬硬钢和马氏体不锈钢》.pdf

SANS 1700-17-9-1996 Fasteners Part 17 Pins Section 9 Taper pins with internal thread unhardened《紧固件 第17部分：销 第9节：带内螺纹圆锥销 不淬硬》.pdf

SANS 1700-18-1-2003 Fasteners Part 18 Rivets Section 1 Rivet shank diameters《紧固件 第18部分：铆钉 第1节：铆钉杆直径》.pdf

SANS 1700-18-10-2004 Fasteners Part 18 Rivets Section 10 Open end blind rivets with break pull mandrel and protruding head - St St《紧固件 第18部分：铆钉 第10节：开口型盘头抽芯盲铆钉 St St》.pdf

SANS 1700-18-11-2004 Fasteners Part 18 Rivets Section 11 Open end blind rivets with break pull mandrel and countersunk head - St St《紧固件 第18部分：铆钉 第11节：开口型沉头抽芯盲铆钉 St St》.pdf

SANS 1700-18-12-2004 Fasteners Part 18 Rivets Section 12 Open end blind rivets with break pull mandrel and protruding head - AIA AIA《紧固件 第18部分：铆钉 第12节：开口型盘头抽芯盲铆钉 AIA AIA》.pdf