SNI 1903-2011 Technical specification of rubber.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

DIN 22261-6-2015 Excavators spreaders and auxiliary equipment in opencast lignite mines - Part 6 Examination of ropes and rope end fittings《褐煤露天矿挖掘机、推土机和辅助设备 第6部分 绳索和绳索端紧固件的检验》.pdf

DIN 22270-2012 Continuous Surface Miner (CSM) - Safety《露天采矿机 (CSM) 安全性》.pdf

DIN 2231-2008 Geometrical product specifications (GPS) - Limit gap gauges and forged gauging members over 3 mm up to 100 mm nominal size《产品几何量技术规范(GPS) 标称尺寸3～100mm的界限隙规和锻制量规体》.pdf

DIN 2232-2008 Geometrical product specifications (GPS) - Gap gauges GO with forged gauging member over 3 mm up to 100 mm nominal size《产品几何量技术规范(GPS) 锻造量规体标称直径3～100mm的过端隙规》.pdf

DIN 2233-2008 Geometrical product specifications (GPS) - Gap gauges NOT GO with forged gauging member over 3 mm up to 100 mm nominal size《产品几何量技术规范(GPS) 带锻制量规体标称尺寸3～100mm的不过端隙规》.pdf

DIN 2239-2006 Geometrical product specifications (GPS) - Gauge in dimensional metrology - Requirements and testing《产品几何量技术规范(GPS) 尺寸计量量规 要求和检验》.pdf

DIN 2240-1-2001 Geometrical Product Specification (GPS) - Handles - Part 1 For gauging members with taper lock 1 50 up to 40 mm nominal diameter《几何产品规范(GPS) 手柄 第1部分 公称直径可达40mm的带1 5.pdf

DIN 2240-2-2001 Geometrical Product Specification (GPS) - Handles - Part 2 For gauging members over 40 mm nominal diameter Handles fixing screws and clamps《几何产品规范(GPS) 手柄 第2部分 公称直径.pdf

DIN 22400-1990 Control units of winding engines hoists and winches for mining《提升机的控制装置 采矿用起重机和绞车》.pdf