TCVN 4651-1988 Sandstone Determination of cerium oxide content《砂岩 氧化铈含量的测定》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD WSK-M4D642-A2-2009 POLYAMIDE (PA) 66 HEAT STABILIZED 30% GLASS FIBER REINFORCED MOLDING COMPOUND INTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车内部用受热稳定、30%玻璃纤维增强的聚酰胺66成型料 .pdf

FORD WSK-M4D642-A3-2006 POLYAMIDE (PA) 66 HEAT STABILIZED 30% GLASS FIBER REINFORCED REDUCED MOISTURE ABSORPTION MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A (Use WSK-M4D.pdf

FORD WSK-M4D643-A1-2010 POLYPROPYLENE (PP) HOMOPOLYMER 40% MINERAL FILLED MELT FLOW RATE 4 - 7 TO BE USED WITH FORD WSS-M99P1111-A 《熔体流动速率为4-7的40%矿物填充的聚丙烯(PP)均聚物 与标准FORD WSS-M99.pdf

FORD WSK-M4D643-A2-2011 POLYPROPYLENE (PP) HOMOPOLYMER 40% MINERAL FILLED MELT FLOW RATE 1 - 3 5 TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSK-M4D643-A1)《40%矿物填充熔态流动率为1-.pdf

FORD WSK-M4D644-A-2004 POLYPROPYLENE (PP) HOMOPOLYMER 40% MINERAL FILLED CONTROLLED RHEOLOGY (CR) GRADE TO BE USED WITH FORD WSS-M99P1111-A 《流变性能(CR)控制级40%矿物填充的聚丙烯(PP)均聚物 与标准FOR.pdf

FORD WSK-M4D644-A2-2011 POLYPROPYLENE (PP) HOMOPOLYMER 40% MINERAL MIX FILLED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《聚丙烯均聚物 40%矿物混合填充模塑材料 与福特WSS-M99P1111-A 一起使用》.pdf

FORD WSK-M4D644-A4-2011 POLYPROPYLENE (PP) HOMOPOLYMER 40% MINERAL MIX FILLED HIGH HEAT MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《40%矿物混合填充高热量聚丙烯(PP)均聚物模塑材料 与福特WSS-M.pdf

FORD WSK-M4D645-A-2009 POLYETHYLENE (PE) HIGH DENSITY MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《聚乙烯（PE）高密度成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD WSK-M4D646-A-2010 POLYVINYL CHLORIDE (PVC) RIGID MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《聚氯乙烯（PVC）刚性成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf