TCVN 4778-2009 Coal Determination of bulk density《煤 堆积密度的测定》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

DIN 7172-1991 Tolerances and limit deviations for sizes above 3150 mm up to 10000 mm principles standard tolerances and limit deviations《规格范围在 3150 mm - 10 000 mm 以上的公差和极限偏差 原则、标准公.pdf

DIN 7178-1 Bb 1-1973 System of cone tolerances and cone fits for conical workpieces of cones from C = 1 3 to 1 500 and lenghts from 6 to 630 mm methods for testing of internal an.pdf

DIN 7178-1-1974 System of cone tolerances and cone fits for conical workpieces from C = 1 3 to 1 500 and lengths from 6 to 630 mm system of cone tolerances《锥形工件C=1 3至1 500及长度6至63.pdf

DIN 7178-2-1986 System of cone tolerances and cone fits for conical workpieces of cones from C = 1 3 to 1 500 and lengths from 6 to 630 mm system of cone fits《锥度C=1 3至1 500及长度6至6.pdf

DIN 7178-3-1986 System of cone tolerances and cone fits for conical workpieces of cones from C = 1 3 to 1 500 and lengths from 6 to 630 mm effect of the deviations on cone with r.pdf

DIN 7178-4-1986 System of cone tolerances and cone fits for conical workpieces of cones from C = 1 3 to 1 500 and lengths from 6 to 630 mm axial displacements《锥度C=1 3至1 500及长度6至6.pdf

DIN 7178-5-1976 System of cone tolerances and cone fits for conical workpieces of cones from C = 1 3 to 1 500 and lengths from 6 to 630 mm vocabulary in German English French Ita.pdf

DIN 7190-1-2017 Interference fits - Part 1 Calculation and design rules for cylindrical self-locking pressfits《过盈配合 第1部分 圆柱形自锁压入的计算和设计规则》.pdf

DIN 7190-2-2017 Interference fits - Part 2 Calculation and design rules for conical self-locking pressfits《过盈配合 第2部分 圆锥形自锁压入的计算和设计规则》.pdf