1、TIAIEIA INTERIM STANDARD TIAIEIA-4 1 -D Enhancements For Internationalization TIA/EIA/IS-807 AUGUST 1999 TELECOMMUNICATIONS INDUSTRY ASSOCIATION Electronic ladustria blliance STD-EIA TIA/EIA/IS-807-ENGL 1979 E 323LIbOO Ob25b30 423 R NOTICE TIA/EIA Engineering Standards and Publications are designed
2、to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of suc
3、h Standards and Publications shall not in any respect preclude any member or nonmember of TIA/EIA from manufacturing or seiiing products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by those other than TIA/
4、EIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by TIA/EIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA/EIA does not assume any liability to any patent owner, nor
5、does it assume any obligation whatever to parties adopting the Standard or Publication. TIA/EIA INTERIM STANDARDS TIA/EIA Interim Standards contain information deemed to be of technical value to the industry, and are published at the request of the originating Committee without necessarily following
6、 the rigorous public review and resolution of comments which is a procedural part of the development of a TIA/EIA Standard. TIA/EIA Interim Standards should be reviewed on an annual basis by the formulating Committee and a decision made on whether to proceed to develop a TIA/EIA Standard on this sub
7、ject. TIA/EIA Interim Standards must be cancelled by the Committee and removed from the TIA/EIA standards Catalog before the end of their third year of existence. Publication of this TIAEIA Interim Standard for trial use and comment has been approved by the Telecommunications Industry Association. D
8、istribution of this TiA/EIA Interim Standard for comment shall not continue beyond 36 months from the date of publication. It is expected that following this 36 month period, this TIA/EIA Interim Standard, revised as necessary, will be submitted to the American National Standards Institute for appro
9、val as an American National Standard. Suggestions for revision should be directed to: Standards December 1997. V Foreword STD-EIA TIA/EIA/IS-O-f ENGL 1999 B 3234b00 Ob25b3b 941 I TiNEINIS-807 EDITORIAL KEY 1 2 3 4 5 6 7 8 This section identifies the editorial style for the use of the right-hand marg
10、in vertical difmiarks, strikethrough lines, and underscore lines. The editorial style employed is: a. TIAIEIA-41-D original text deleted by IS-SO7 has a strikethrough line. b. Original text added by 1-07 has a single underline. 9 10 c. Both additions and deletions are indicated by a right hand margi
11、n vertical 11 diffmark. 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 Editoriai Key vi 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 la 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 4
12、1 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 5a 59 60 0.0 STD*EIA TIA/EIA/IS-807-ENGL 1979 I 3234b00 Ob25b37 888 August, 1999 Initial Publication TINEINIS-807 The following items are basic understandings used during the development of this document: a. E.212 global title translation is provisio
13、ned for message routing between national networks. b. A national SS7 network is an administrative set of SS7 nodes that are interconnected by a common national signaling point code addressing scheme. The signai transfer points which reside in both the international and national signaling levels e.,
14、gateway STPs) convert from national MTP and SCCP to international MTP and SCCP and vice versa. This conversion includes changes to global title indicator, translation type, numbering plan, encoding scheme, and nature of address indicator. c. d. Intemational addressing implementations not employing g
15、lobal title translation are beyond the scope of this interim standard. An MSC supporting IS-807 or later is assumed to be capable of receiving digit srings in parameters of DigitsType with Nature of Number indicating International as well as in parameters of DigitsType with Nature of Number indicati
16、ng National. Moreover, if the MSC receives a digit string containing the International encoding of E. 164 number from its own countrys telephony numbering plan (or the leading digits of such a number), the MSC is assumed to be capable of stripping the country code from that digit string to convert i
17、t to National (Significant) Number form. e. REVISION HISTORY I Revision I Date 1 Remarks 1 vii Assumptions 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 59 51 52 53 54 55 56 57 58 59 60 TIAIEI AIIS-807 I. INT
18、RODUCTION 1 .I OBJECTIVE This Interim Standard (IS-807) provides recommendations for supporting internationalization enhancements for ANSI/TWEIA-4l-D. i .2 SCOPE This document specifies the ANSI/TIA/EIA-4l-D Chapters 1, 3, 5 and 6 enhancements that are necessary to support intemationai intersystem o
19、perations. 1.3 ORGANIZATION This document is organized as per ANSI/TIA/EIA-41-D. 1 Introduction STD.EIA IA/EIA/IS-807-ENGL 1999 E! 323Lib00 Ob25b39 b50 B TINEINIS-807 2. TIAIEIAm41-D Chapter I “Functional Overview” Modifications 2.1 NORMATIVE REFERENCES (TIAIEIA-41-D Chapter 1, page 1-2) ITU-T: Reco
20、mmendation E.212 - The International Identification Plan for Mobile Terminals and Mobile Users. November 1998. Recommendation O. 713 f07/96) - Sianallina Connection Control Part formats and codes. July 1996. ANSI T1 Standards: ANSI T1.112-988 Signaling System Number 7 - Signaling Connection Control
21、Part (SCCP) TIMEIA: TIAIEIA IS-751 TIA/EIA 41-0 Modifications to Suvvort IMSI, February 1998. 3.1 DEFINITIONS (TIAIEIA-41-D Chapter 1, page 1-5) International Mobile Subscriber Identitv (IMSI) The IMSI is a string of decimal digits, UD to a maximum of 15 digits, that identifies a uniaue mobile termi
22、nal or mobile subscriber intemationallv. The IMSI consists of three fields: the mobile country code, the mobile network code, and the mobile subscriber identification number. Mobile Station Identitv IMSID) The identifier for a mobile station. A choice of either MIN or IMSI. 4 SYMBOLS AND ABBREVIATIO
23、NS (T/A/A-41-0 Chapter i, page 1-14) IMSI International Mobile subscriber Identiy MSID Mobile Station Identity 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 25 26 27 28 29 31 32 33 34 37 38 39 40 41 42 43 44 47 48 49 50 53 54 55 56 57 58 59 60 Functional Overview 2 TIAIEIA-41-O Chapter I
24、Modifications 1 2 3 4 5 6 7 8 9 10 il 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 26 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 STD-EIA TIA/EIA/IS-07-ENGL 1999 II 323Lib00 Ob25bLi0 372 m TINEIN15807 7 GENERAL BACKGROUND AND ASSUMPTIONS (TIAiEi
25、A-41-D Chapter 1, page 1-30) A&ocedures for the implementation of the identified intersystem services have been defined with due regard to the following general considerations: I 8) The procedures defined here are based on the assumption that intersystem handoff relies upon dedicated intersystem tru
26、nks. This is required since intersystem handoff is a tightly controlled activity of the cellular systems involved. Intersystem handoff cannot be considered any differently than an inter- cell handoff. 1 I TiA/EiA-41-D Chapter 1 Modifications 3 Functional Overview 3. TIAIEIA-41-D Chapter 3 “Automatic
27、 Roaming Information Flows” Modifications 4.17.2 Successful LocationRequest: Route to a Local MS (TZd/EZ,4-4I-D Chapter 3, page 3-76) b. The HLR determines that the call shall be routed to a local MS (i.e., an MS served by the Onginating MSC) and returns this information to the Originating MSC in th
28、e locreq. Stage2 Scenarios I ?arameters are as in Section 4.18.1, Step-b, with the exception that PSNRoutingInfo is not included and with the following additions: arameters C-SSN salRoutinginfo: frerminationList Digitsestination) Jsage 3riginating MSC PCSSN. Include if SS7 lall routing information:
29、carriage services are used. Local termination information. Include if TerminationList is allowed. Destination digits for use in intra-MSC call routing (my be MSs MIN). Include if applicable and if TerminationList is not allowed. Special routing instructions. Include if applicable and if not specifie
30、d within the TerminationList parameter. interA4TA exchange call routing. Include if applicable and if not specified within the TerminationList paiameter. Called subscribers PIC for use in intra-MSC, 4 Type O O O O O TlAIElA4I-D Chapter 3 Modifications 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 15
31、20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 STD-EI
32、A TIA/EIA/IS-807-ENGL 1999 m 323Lib00 Ob25bLi2 195 m TINEINIS-807 4.17.3 Successful LocationRequest: Route to an MS on Another MSC (TIA/EIA-41-D Chapter 3, page 3-77) b. The HLR determines that the call shall be routed to an MS on another MSC and returns this information to the Originating MSC in th
33、e locreq. Parameters are as in Section 4.17. i, Step-b, with the exception that PSTNRoutingInfo is not included and with the following additions: PC-SSN Inters ystemRoutingInfo: TerminationList Digits(Destination) RoutingDigits Digits(Carrier) Jsage Serving MSC PC-SSN. Include if SS7 carriage servic
34、es are used. lall routing information: Intersystem termination information. Include if Destination digits for use in inter-MSC call routing. Include if TerminationList is not allowed. TerminationList is allowed. Special routing instructions. Include if applicable and if not specified within the Term
35、inationList parameter. inter-LG4 exchange call routing. Include if applicable and if not specified within the TerminationList parameter. Called subscribers PIC for use in inter-MSC, TIAiEIA-41-D Chapter 3 Modifications 5 Stage-2 Scenarios STD-EIA TIA/EIA/IS-07-ENGL 1977 I 323Lib00 Ob25b113 O1 = TIAI
36、EINiS-807 4.17.5 Successful LocationRequest: Route to Multiple Terminations (TIA/EIA-II-D Chapter 3, page 3-79) b. The HLR determines that the cai1 shall be routed to multiple terminations and returns this information to the Originating MSC in the locreq. Stage-2 Scenarios Parameters are as in Secti
37、on 4.1 7.1, Step-b, with the exception that MSCID, PC-SSN, and PSTNRoutingInfo are not included and with the following additions: Parameters MultipleRoutingInfo: TerminationList RoutingDigits Digits(Canier) Usage Call routing information: Multiple termination information. Special routing instruction
38、s. Include if applicable and if not specified within the TerminationList parameter. Called subscribers PIC for use in inter-MSC, inter-WTAexchanee call routing. Include if applicable and if not specified within the TerminationList parameter. 60 6 TIAIEIA-41-D Chapter 3 Modifications 1 2 3 4 5 6 7 8
39、9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 1 2 3 4 5 6 7 a 9 10 11 12 13 14 15 16 17 ia 19 20 27 22 23 24 25 26 27 2a 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 5
40、3 54 55 56 57 58 59 w STD-EIA TIA/EIA/IS-B07-ENGL 1777 I 3234h00 Ob25blii TL8 I TINEINIS-807 4. TIAIEIA=41-D Chapter 5 “Signaling Protocol” Modifications 5.1 ANSI SS7-BASED DATA TRANSFER SERVICES (TIAEiA-41-D Chapter 5, page 5-6) 5.1.2 Signaling Connection Control Part (TIAEiA-II-D Chapter 5, page 5
41、-8) For TIA/EIA-41 applications, the SCCP is defined in ANSI TI.112, with the following exceptions and limitations: SCCP Class O connectionless service is used. The message types are Unitdata (UDT) and Unitdata Service (UDTS). The SCCP shall return a UDTS message when a received UDT message cannot b
42、e delivered to the specified destination and has the return message on error option set. Whether to set the return message on error or discard message on error option in the Protocol Class parameter of the UDT message is at the discretion of the implementation. The TIMEIA-41 Mobile Application Part
43、has assigned the following Subsystem Numbers (SSN). Use of the following SSN values %se & recommended: - 5: Mobile Application Part (MAP) -6: Home Location Register (HLR) -7: Visitor Location Register (VLR) - 8: Mobile Switching Center (MSC) -9: Equipment Identification Register (EIR) (reserved) -1
44、O: Authentication Center (AC) - 11: Short Message Service In accordance with ANSI TI.112 an SSN shall be included in all messages even if message routing is based on Global Title Translation (GTT). The null SSN (i.e., value O) should be used when the subsystem is not known (e.g., before a global tit
45、le translation takes place) per ANSI T1.112. Global title addresses are reauired in the SCCP Called Pam Address and the SCCP Calling Parh Address for international roaming puruoses. Detailed transactions relative to SSN value 9 are for further study. TiNElA-41-D Chapter 5 Modifications 7 Stage-3 Sig
46、naling Protocol Global Title Translation on Mobile Identification Number can be used for communication with the HLR on the ANSI SS7 network. The following encoding may be used: Table 5.1.2a ANSI SS7 - MIN to HLR Global Title Field Address Indicator Subfield Value SSN Indicator 1 Point Code Indicator
47、 O or 1 I Global Title Indicator 12 (00102) Subsystem Number Routing Indicator O National or International Indicator 1 (National use) Include applicable value ifknown or zero Global Title Translation Type 3 (O00000 1 12) “Cellular Nationwide Roaming Service” I Address Information I MIN . A911- &,.a
48、?.!I? o- An administrative set of SS7 nodes that are interconnected by a common national signaling Doint code addressing scheme. 1 2 3 4 5 6 7 a 9 10 11 12 13 14 15 16 17 16 19 20 21 22 23 24 25 26 27 2a 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
49、Stage-3 Signaling Protocol 8 TIAiEIA-41-D Chapter 5 Modifications 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 P 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 41 48 49 50 51 52 53 54 55 56 57 58 59 60 Field Sub-field Address Indicator SSN Indicator TINEINS-807 Value 1 Global Title Translation on Mobile Identification Number can be used for communication with a Message Center on the ANSI SS7 network. The following, encoding can be used: Subsystem Number Global Title Include applicable value if
