1、 TIA STANDARD MEID for cdma2000 Spread Spectrum Systems TIA-1082 September 2005 TELECOMMUNICATIONS INDUSTRY ASSOCIATION The Telecommunications Industry Association represents the communications sector of NOTICE TIA Engineering Standards and Publications are designed to serve the public interest thro
2、ugh eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards and Publication
3、s shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically or interna
4、tionally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication
5、. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations b
6、efore its use. (From Standards Proposal No. 3-0218, formulated under the cognizance of the TIA TR-45.5Committee on Spread Spectrum Digital Technology). Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Standards and Technology Department 2500 Wilson Boulevard Arlington, VA 22201 U.S.A. PRICE: Ple
7、ase refer to current Catalog of TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION STANDARDS AND ENGINEERING PUBLICATIONS or call Global Engineering Documents, USA and Canada (1-800-854-7179) International (303-397-7956) or search online at http:/www.tiaonline.org/standards/search_n_order.cfm All rights re
8、served Printed in U.S.A. NOTICE OF COPYRIGHT This document is copyrighted by the TIA. Reproduction of these documents either in hard copy or soft copy (including posting on the web) is prohibited without copyright permission. This document contains significant portions of material copied from ETSI d
9、ocument number TS 102188-5v112. The copyright on the ETSI document is owned by the European Telecommunication Standards Institute, which has granted a license for reproduction for use by TIA and its Engineering Committees and Subcommittees. Any copies of the above-mentioned ETSI document(s) required
10、 for other purposes should be purchased directly from ETSI or other organizations with a sales agreement covering ETSI publications. For copyright permission to reproduce portions of this document, please contact the TIA Standards Department or go to the TIA website (www.tiaonline.org) for details o
11、n how to request permission. Details are located at: http:/www.tiaonline.org/about/faqDetail.cfm?id=18 OR Telecommunications Industry Association Standards (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (c) the
12、 Document may be amended, modified or changed in the standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes
13、 no search or investigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obli
14、gation to investigate or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonabl
15、e or non-discriminatory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. TIA does not enforce or monitor compliance with the contents of the Document. TIA does not certify, inspect, t
16、est or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS F
17、OR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NON-INFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY A
18、PPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE O
19、F THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE),
20、 PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. TIA-1082 CONTENTS i FOREWORDv 1 NOTES vii 2 RE
21、FERENCES ix 3 1 GENERAL1-1 4 1.1 Acronyms and Abbreviations 1-1 5 1.2 Terms1-1 6 1.3 Numeric Information.1-2 7 2 AIR INTERFACE REQUIREMENTS2-1 8 2.1 Mobile Station Requirements .2-1 9 2.1.1 MEID and ESN 2-1 10 2.1.1.1 Pseudo-ESN 2-1 11 2.1.2 Setting of the Station Class Mark field .2-2 12 2.1.3 Info
22、rmation Records2-3 13 2.1.4 Public Long Code Mask Type 2-4 14 2.1.4.1 Public Long Code Mask Formats.2-4 15 2.1.4.1.1 Public Long Code Mask PLCM_42.2-5 16 2.1.5 Reject Order2-6 17 2.1.6 Channel Assignment Processing.2-6 18 2.1.6.1 P_REV_IN_USE greater than or equal to 11 2-6 19 2.1.6.2 P_REV_IN_USE e
23、qual to 9 or 102-6 20 2.1.6.3 P_REV_IN_USE equal to 6, 7 or 82-7 21 2.1.7 Handoff Processing .2-8 22 2.1.7.1 P_REV_IN_USE greater than or equal to 11 2-8 23 2.1.7.2 P_REV_IN_USE equal to 9 or 102-8 24 2.1.7.3 P_REV_IN_USE equal to 6, 7 or 82-8 25 2.1.8 Over-the-Air Service Provisioning .2-9 26 2.2 B
24、ase Station Requirements 2-10 27 2.2.1 Extended Channel Assignment Message 2-10 28 2.2.1.1 MSG_ID.2-10 29 2.2.1.2 P_REV_IN_USE greater than or equal to 11 2-10 30 2.2.1.3 P_REV_IN_USE equal to 9 or 102-11 31 TIA-1082 CONTENTS ii 2.2.1.4 P_REV_IN_USE equal to 8. 2-11 1 2.2.1.5 P_REV_IN_USE equal to 7
25、. 2-13 2 2.2.1.6 P_REV_IN_USE equal to 6. 2-14 3 2.2.2 Universal Handoff Direction Message. 2-17 4 2.2.2.1 MSG_TYPE 2-17 5 2.2.2.2 P_REV_IN_USE greater than or equal to 11 2-18 6 2.2.2.3 P_REV_IN_USE equal to 9 or 10 2-18 7 2.2.2.4 P_REV_IN_USE equal to 8. 2-18 8 2.2.2.5 P_REV_IN_USE equal to 7. 2-2
26、0 9 2.2.2.6 P_REV_IN_USE equal to 6. 2-21 10 2.2.3 Base Station Assigned PLCM 2-27 11 12 TIA-1082 TABLES iii 1 Table 2.1.1-1. Permanent Mobile Station Indicators .2-1 2 Table 2.1.2-1. Station Class Mark .2-3 3 Table 2.1.3-1. Information Record Types.2-3 4 Table 2.1.5-1. Order and Order Qualification
27、 Codes Used on r-dsch and r-csch 2-6 5 Table 2.2.1.1-1. MSG_ID Values on f-csch 2-10 6 Table 2.2.1.4-1. The Public Long Code Mask Type 2-12 7 Table 2.2.1.6-1. MECAM RESERVED BLOB for P_REV_IN_USE = 6 2-16 8 Table 2.2.2.1-1. MSG_TYPE Values for Regular PDUs on f-dsch .2-17 9 Table 2.2.2.6-1. MUHDM RE
28、SERVED_BLOB for P_REV_IN_USE=6.2-23 10 Table 2.2.3-1. The Base Station Assigned Public Long Code Mask Type.2-28 11 12 13 TIA-1082 FIGURES iv 1 Figure 2.1.4.1-1. Public Long Code Mask PLCM_42 format 2-6 2 3 TIA-1082 FOREWORD v (This foreword is not part of this Standard) 1 This Standard was prepared
29、by Technical Specification Group C of the Third Generation 2 Partnership Project 2 (3GPP2). This Standard contains the air interface requirements for 3 implementing Mobile Station Equipment Identifier (MEID) otherwise set 23 PLCM_TYPES as described in 7. 24 2.1.4.1 Public Long Code Mask Formats 25 T
30、he PLCM formats described below are exactly as in 7. 26 The 42 bit Public Long Code Mask PLCM_42 is generated using PLCM_37 or PLCM_40 27 as defined in section 2.1.4.1.1 where the least significant bits PLCM_37 or PLCM_40 28 are set as defined in this section below. 29 If PLCM_TYPEsis equal to 0000,
31、 the 37 least significant bits (PLCM_37) are set as 30 follows: 31 TIA-1082 2-5 Bits M36 through M32 shall be set to 11000; 1 Bits M31 through M0 shall be set to a permutation of the mobile stations ESN 2 as follows: 3 ESN = (E31, E30, E29, E28, E27, E26, E25, . . . E2, E1, E0) 4 Permuted ESN = (E0,
32、 E31, E22, E13, E4, E26, E17, E8, E30, E21, E12, E3, E25, 5 E16, E7, E29, E20, E11, E2, E24, E15, E6, E28, E19, E10, E1, 6 E23, E14, E5, E27, E18, E9). 7 If PLCM_TYPEsis equal to 0001, the 40 least significant bits (PLCM_40) are set as 8 follows: 9 Bit M39shall be set to 1; 10 Bits M38through M0of t
33、he public long code mask shall be specified by 11 PLCM_39sand shall be set as follows: 12 PLCM_39s= (P38, P37, P36, P35, P34, P33, P32, . . . P2, P1, P0) 13 If PLCM_TYPEsis equal to 0010, the 37 least significant bits (PLCM_37) are set as 14 follows: 15 Bits M36through M34shall be set to 001; 16 Bit
34、s M33through M0shall be set to IMSI_O_S. 17 If PLCM_TYPEsis equal to 0011, the 37 least significant bits (PLCM_37) are set as 18 follows: 19 Bits M36through M34shall be set to 000; 20 Bits M33through M0shall be set to IMSI_O_S. 21 If PLCM_TYPEsis equal to 0100, the 40 least significant bits (PLCM_40
35、) are set as 22 follows: 23 Bit M39shall be set to 0; 24 Bits M38through M0shall be set as follows: the 39 least significant bits of the 25 SHA-1 digest of the MEID4. See 10 for the specification of the SHA-1 algorithm. 26 2.1.4.1.1 Public Long Code Mask PLCM_42 27 If PLCM_37 is defined, the public
36、long code mask PLCM_42 shall be as follows: bits 28 M36through M0of the public long code mask shall be specified by PLCM_37 (see 29 2.1.4.1). Bits M41through M37shall be set to 11000. The resulting public long code 30 mask PLCM_42 is shown in Figure 2.1.4.1-1 (a). 31 If PLCM_40 is defined, the publi
37、c long code mask PLCM_42 shall be as follows: bits 32 M39through M0of the public long code mask shall be specified by PLCM_40 (see 33 4Example: if the 56-bit MEID is (hexadecimal) FF 00 00 01 12 34 56, the bits M38through M0of PLCM are (hexadecimal) 1A 0E 07 37 E1, and (binary) 001 1010 0000 1110 00
38、00 0111 0011 0111 1110 0001. TIA-1082 2-62.1.4.1). Bits M41through M40shall be set to 10. The resulting public long code 1 mask PLCM_42 is shown in Figure 2.1.4.1-1 (b). 2 b) Public Long Code Mask PLCM_42 given PLCM_4010PLCM_4041 40 39 . 0a) Public Long Code Mask PLCM_42 given PLCM_3711 000 PLCM_374
39、1 40 39 . 37 36 . 03 4 Figure 2.1.4.1-1. Public Long Code Mask PLCM_42 format 5 2.1.5 Reject Order 6 The mobile station shall support the Mobile Station Reject Order as specified in Table 7 2.1.5-1 (corresponding to Table 2.7.3-1 of 7). The structure of the Mobile Station Reject 8 Order shall be as
40、specified in 7. 9 Table 2.1.5-1. Order and Order Qualification Codes Used on r-dsch and r-csch 10 r-csch Order r-dsch Order Order Code, ORDER (binary) Order Qualification Code, ORDQ (binary) More Fields other than ORDQ Support Reqd Name/Function Y Y 011111 00011100 Y Y Mobile Station Reject Order (P
41、LCM_TYPE mismatch) 11 2.1.6 Channel Assignment Processing 12 2.1.6.1 P_REV_IN_USE greater than or equal to 11 13 If P_REV_IN_USES is greater than or equal to 11, there are no additional requirements 14 on the mobile station. 15 2.1.6.2 P_REV_IN_USE equal to 9 or 10 16 Requirements in this section ar
42、e applicable if P_REV_IN_USES is equal to 9 or 10. 17 TIA-1082 2-7The mobile station shall process Extended Channel Assignment Message in Page 1 Response Substate and Mobile Station Origination Attempt Substate as follows: 2 If PLCM_TYPErequals 0010 and IMSI_O is derived from IMSI_T, or if 3 PLCM_TY
43、PErequals 0011 and IMSI_O is derived from IMSI_M, the mobile 4 station shall send a Mobile Station Reject Order with the ORDQ field set to 5 00011100 (PLCM_TYPE mismatch), the mobile station shall not process the 6 message. 7 If the message is not rejected as described above, then the requirements f
44、or processing 8 Extended Channel Assignment Message shall be as defined in 2 per the MOB_P_REVp9 of the mobile station with additional requirements listed below: 10 If PLCM_TYPE_INCLris equal to 1 and PLCM_TYPEris not set to 0000 or 11 0001, then the mobile station shall perform the following to det
45、ermine the long 12 code mask to use after the channel assignment: 13 The mobile station shall use the public long code mask derived from 14 PLCM_TYPEsas specified in 2.1.4. 15 2.1.6.3 P_REV_IN_USE equal to 6, 7 or 8 16 Requirements in this section are applicable if P_REV_IN_USES is equal to 6, 7 or
46、8. 17 The mobile station shall process the MEID Extended Channel Assignment Message in 18 Page Response Substate and Mobile Station Origination Attempt Substate as follows: 19 If PLCM_TYPErequals 0010 and IMSI_O is derived from IMSI_T, or if 20 PLCM_TYPErequals 0011 and IMSI_O is derived from IMSI_M
47、, the mobile 21 station shall send a Mobile Station Reject Order with the ORDQ field set to 22 00011100 (PLCM_TYPE mismatch), the mobile station shall not process the 23 message. 24 If the message is not rejected as described above, then the requirements for processing 25 MEID Extended Channel Assig
48、nment Message shall be same as requirements for 26 processing Extended Channel Assignment Message defined in 2 per the MOB_P_REVp27 of the mobile station with additional requirements listed below: 28 If PLCM_TYPE_INCLris equal to 1 the mobile station shall perform the 29 following to determine the l
49、ong code mask to use after the channel assignment: 30 The mobile station shall set PLCM_TYPEsto PLCM_TYPEr. 31 The mobile station shall set PLCM_39sto PLCM_39rif PLCM_TYPEris equal 32 to 0001. 33 The mobile station shall use the public long code mask derived from 34 PLCM_TYPEsas specified in 2.1.4. 35 TIA-1082 2-82.1.7 Handoff Processing 1 2.1.7.1 P_REV_IN_USE greater than or equal to 11 2 If P_REV_IN_USEsis greater than or equal to 11, there are no additional requirements 3 on the mo
