TIS 1355-1996 Motorcycles safety requirements emission from engine level 3 engine capacity not exceeding 125 cubic centimetres《摩托车 安全性要求 发动机排放 3级 发动机排量不超过125立方厘米》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

AGMA 92FTM12-1992 Noise Reduction in a Plastic and Powder Metal Gear Set Through Control of Mean Involute Slope 《通过控制“平均渐开斜率”降低塑料和粉末金属齿轮装置的噪声》.pdf

AGMA 92FTM2-1992 Face Gear Drives Design Analysis and Testing for Helicopter Transmission Applications《平面齿轮驱动器.直升机传动系统的设计 分析和试验》.pdf

AGMA 92FTM3-1992 Reduced Fuel Consumption and Emissions due to Better Integration of Engine and Transmission《由于引擎和传动装置的优化集成而导致的油耗和排放的减少》.pdf

AGMA 92FTM4-1992 The Design Development and Manufacture of Advanced Technology Gearing for Hot Strip Rolling Mill Applications《热轧带滚轧系统用先进齿轮传动的设计 开发和制造》.pdf

AGMA 92FTM5-1992 Main Advantages of Non-Involute Spur Gears The Design of Non-Involute Spur Gears to Improve the Condition of Contact《非渐开线正齿轮的主要优势.用于改进接触条件的非渐开线正齿轮的设计》.pdf

AGMA 92FTM6-1992 Comparison of Carburized Gear Materials in Pitting《发生点蚀的渗碳齿轮材料的比较》.pdf

AGMA 92FTM7-1992 Difference in the Local Stress of the Gear Tooth Root Based On Hobbing Cutters and Pinion Cutters《基于滚齿刀和插齿刀的齿根局部应力的差别》.pdf

AGMA 92FTM8-1992 The Role of Reliability for Bearings and Gears《可靠性对于轴承和齿轮的重要性》.pdf

AGMA 92FTM9-1992 Representative Form Accuracy of Gear Tooth Flanks on the Prediction of Vibration and Noise of Power Transmission《电力传输震动和噪声预测的代表齿面形状精度》.pdf