TS 2686-1977 NIGH-VOLTAGE ALTERNATING-CURRENT CIRCUIT-BREAKERS PART 1 GENERAL AND DEFINITIONS《交流高压断路器 第1部分：一般和定义》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

DIN EN 12573-1-2000 Welded static non-pressurised thermoplastic tanks - Part 1 General principles German version EN 12573-1 2000《焊接非承压热塑固定槽罐 第1部分 总则》.pdf

DIN EN 12573-2-2000 Welded static non-pressurised thermoplastic tanks - Part 2 Calculation of vertical cylindrical tanks German version EN 12573-2 2000《焊接固定无压力热塑性塑料槽罐 第2部分 立式圆柱形槽罐的.pdf

DIN EN 12573-3-2000 Welded static non-pressurized thermoplastic tanks - Part 3 Design and calculation for single skin rectangular tanks German version EN 12573-3 2000《焊接非承压热塑固定槽罐 第.pdf

DIN EN 12573-4-2000 Welded static non-pressurised thermoplastic tanks - Part 4 Design and calculation of flanged joints German version EN 12573-4 2000《焊接非承压热塑固定槽罐 第4部分 法兰连接的设计和计算》.pdf

DIN EN 12574-1-2017 en 8448 Stationary waste containers - Part 1 Containers with a capacity up to 10000 l with flat or dome lid(s) for trunnion double trunnion or pocket lifting de.pdf

DIN EN 12574-2-2017 Stationary waste containers - Part 2 Performance requirements and test methods German version EN 12574-2 2017《固定式垃圾箱 第2部分 性能要求和试验方法 德文版本EN 12574-2-2017》.pdf

DIN EN 12574-3-2017 Stationary waste containers - Part 3 Safety and health requirements German version EN 12574-3 2017《固定式垃圾箱 第3部分 安全和卫生要求 德文版本EN 12574-3-2017》.pdf

DIN EN 12575-1998 Plastics - Thermoset moulding compounds - Determination of the degree of fibre wet out in SMC German version EN 12575 1998《塑料 热固成形模塑化合物 SMC中纤维湿润级的测定》.pdf

DIN EN 12576-1998 Plastics - Fibre reinforced composites - Preparation of compression moulded test plates of SMC BMC and DMC German version EN 12576 1998《塑料 纤维增强的复合材料 SMC BMC和DMC制模.pdf