UL 14B-2008 UL Standard for Safety Sliding Hardware for Standard Horizontally Mounted Tin-Clad Fire Doors (Ninth Edition Reprint with Revisions Through and Including JULY 17 2017)《.pdf

上传人:周芸 文档编号:1067521 上传时间:2019-04-02 格式:PDF 页数:38 大小:915.98KB
下载 相关 举报
UL 14B-2008 UL Standard for Safety Sliding Hardware for Standard Horizontally Mounted Tin-Clad Fire Doors (Ninth Edition Reprint with Revisions Through and Including JULY 17 2017)《.pdf_第1页
第1页 / 共38页
UL 14B-2008 UL Standard for Safety Sliding Hardware for Standard Horizontally Mounted Tin-Clad Fire Doors (Ninth Edition Reprint with Revisions Through and Including JULY 17 2017)《.pdf_第2页
第2页 / 共38页
UL 14B-2008 UL Standard for Safety Sliding Hardware for Standard Horizontally Mounted Tin-Clad Fire Doors (Ninth Edition Reprint with Revisions Through and Including JULY 17 2017)《.pdf_第3页
第3页 / 共38页
UL 14B-2008 UL Standard for Safety Sliding Hardware for Standard Horizontally Mounted Tin-Clad Fire Doors (Ninth Edition Reprint with Revisions Through and Including JULY 17 2017)《.pdf_第4页
第4页 / 共38页
UL 14B-2008 UL Standard for Safety Sliding Hardware for Standard Horizontally Mounted Tin-Clad Fire Doors (Ninth Edition Reprint with Revisions Through and Including JULY 17 2017)《.pdf_第5页
第5页 / 共38页
点击查看更多>>
资源描述

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 14B Sliding Hardware for Standard, Horizontally Mounted Tin-Clad Fire DoorsUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRI

2、GHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Sliding Hardware for Standard, Horizontally Mounted Tin-Clad Fire Doors, UL 14B Ninth Edition, Dated December 15, 2008 SUMMARY OF TOPICS Revision pages have been issued for th

3、e Standard for Sliding Hardware for Standard, Horizontally Mounted Tin-Clad Fire Doors, UL 14B, to reect the reaffirmation of the ANSI approval. No changes in requirements have been made. The revisions are substantially in accordance with Proposal(s) on this subject dated March 8, 2013. All rights r

4、eserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed o

5、r implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of

6、 the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electron

7、ic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard

8、on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elements of the Standard having future effective dates as indicated in the note following the affected item. The prior text for requirements that

9、 have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. MAY 3, 2013 UL 14B tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MAY 3, 2013 UL 14B tr2 No Te

10、xt on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL DECEMBER 15, 2008 (Title Page Reprinted: May 3, 2013) 1 UL 14B Standard for Sliding Hardware for Standard, Horizontally Mounted Tin- Clad Fire Doors First Edition March, 1917 Sec

11、ond Edition February, 1943 Third Edition November, 1953 Fourth Edition December, 1968 Fifth Edition June, 1973 Sixth Edition January, 1979 Seventh Edition December, 1993 Eighth Edition December, 1998 Ninth Edition December 15, 2008 This ANSI/UL Standard for Safety consists of the Ninth Edition, incl

12、uding revisions through May 3, 2013. The most recent designation of ANSI/UL 14B as an American National Standard (ANSI) occurred on May 3, 2013. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. The Department of Defense (DoD)

13、 has adopted UL 14B on October 24, 1984. The publication of revised pages or a new edition of this Standard will not invalidate the DoD adoption. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request i

14、n ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall

15、 remain the sole and exclusive property of UL. COPYRIGHT 2013 UNDERWRITERS LABORATORIES INC. ANSI/UL 14B-2008 (R2013)UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL DECEMBER 15, 2008 UL 14B 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT A

16、UTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .4 2 Units of Measurement .4 3 Undated References 5 CONSTRUCTION 4 General 5 5 Flat Tracks .6 5.1 General .6 5.2 Holes for wall bolts .8 6 Hangers 12 6.1 Hangers for three-ply doors .12 6.2 Tr

17、ack wall brackets 12 6.3 Hangers for two-ply doors 13 7 Front Binders 13 8 Rear Binders and Rear-Binder Pockets .14 9 Stay Rolls .17 10 Chang Strips 23 11 Wedges .25 12 Handles .25 13 Bumpers and Bumper Shoes .26 14 Washers .28 15 Tolerances .28 16 Installation Instructions 28 17 Painting .28 MARKIN

18、G 18 General 29 APPENDIXAS I(Metric) Equivalent for USA Units Shown in Figures and Wood Screw Sizes APPENDIX B Tolerances DECEMBER 15, 2008 UL 14B 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These requirements a

19、pply to hardware for horizontally sliding re doors which have demonstrated in re tests re-resistive properties warranting their use with two-ply and three-ply tin-clad re doors tested in accordance with the Standard for Fire Tests of Door Assemblies, UL 10B (NFPA No. 252). 1.2 Requirements for the l

20、ocation and time rating are contained in codes, such as the International Building Code (IBC). The method of installation required for re doors is not included in these codes. Requirements for the details for the installation of horizontally sliding two-ply and three-ply tin-clad re doors are includ

21、ed in the Standard for Fire Doors and Other Opening Protectives, NFPA 80. 1.3 The hardware included in these requirements is designed for mounting standard two-ply and three-ply tin-clad horizontally sliding re doors for protection of openings not exceeding the dimensions for the hourly classication

22、s indicated in Table 1.1. 1.4 These requirements do not cover automatic releasing or closing mechanisms. Table 1.1 Limitations in types and dimensions Type of door Maximum area, Maximum width, Maximum height, Hourly rating ft 2 (m) 2 ft (m) ft (m) Three-ply 120 11.2 12 3.6 12 3.6 3, 1-1/2, 1, 3/4 Tw

23、o-ply 80 7.4 10 3.1 10 3.1 1-1/2, 1, 3/4 2 Units of Measurement 2.1 When a value for measurement is followed by a value in other units in parentheses, the rst stated value is the requirement. SI units as employed are in accordance with the Standard for the Practice for Use of the International Syste

24、m of Units (SI) (the Modernized Metric System), ANSI/ASTM E380-91a. 2.2 The tolerance for all dimensions shall be as specied with the dimension. Where no tolerance is shown, the tolerances specied in Appendix B shall apply. See Appendix B for specications. DECEMBER 15, 2008 UL 14B 4UL COPYRIGHTED MA

25、TERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 3 Undated References 3.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard. CONSTRUCTION

26、 4 General 4.1 Each complete set of hardware for horizontally sliding tin-clad re doors is to include: a) One track, length equal to twice the width of the opening plus 21 in (530 mm) drilled for wall bolts. b) Two hangers for openings 6 ft (1.8 m) and less in width; three hangers for openings wider

27、 than 6 ft (1.8 m), and bolts for attaching hangers to door. c) Two front binders for openings 8 ft (2.4 m) and less in height; three front binders for openings in excess of 8 ft (2.4 m); one rear binder and rear-binder pocket with strip for openings of 7 ft (2.1 m) and not more than 10 ft (3.1 m) i

28、n height; two rear binders and rear- binder pockets with strips for openings exceeding 10 ft (3.1 m). d) One stay roll with attachment bolts required for the form of sill used. e) One bracket for each track bolt. f) Two half-oval chang strips for back of door; two at strips for front of door opposit

29、e of half- oval strips; bolts for fastening above strips together through door; length of strips to be 4 in (102 mm) less than width of door. Doors exceeding 8 ft (2.4 m) in height require three chang strip assemblies. A rear-binder pocket strip to be employed in lieu of the top oval chang strip on

30、doors equipped with two rear-binder pockets. g) One strip 5 in (127 mm) less than width of door to take wear of stay roll; and wood screws for attachment. h) One wedge with screws for attachment. i) Handles with bolts and screws for attachment. j) One front bumper and one back bumper. k) Four bumper

31、 shoes and screws for attachment; each bumper shoe is made in two pieces. l) Washers for all wall bolts. m) Instructions for installation. DECEMBER 15, 2008 UL 14B 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 5 Flat Tracks 5.1 General 5.

32、1.1 Flat tracks shall be made of at-rolled steel with rounded edges 3-1/2 in (89 mm) wide and 3/8 in (9.5 mm) thick. Details are shown in Figure 5.1. 5.1.2 The length shall be equal to twice the width of the opening plus 21 in (533 mm). The length of the track is given in terms of the wall opening,

33、12 in (305 mm) being allowed for the lap and width of the door, 8 in (203 mm) for attaching front and back bumpers, and 1 in (25.4 mm) for clearance when the door is full open. This is generated text for gtxt. DECEMBER 15, 2008 UL 14B 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION

34、OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure 5.1 Hardware for sliding two-ply and three-ply tin-clad doors, including track, hangers, hanger bolts, and track wall brackets Note: See Appendix A for SI Equivalents. DECEMBER 15, 2008 UL 14B 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRO

35、DUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 5.2 Holes for wall bolts 5.2.1 Holes for wall bolts shall be 13/16 in (20.6 mm) in diameter and located so that a wall bolt shall be placed directly opposite each hanger when the door is closed and so that front and back bumpers can be attached to t

36、he end bolts. See Figure 5.1 for details. 5.2.2 The location of bolt holes and the number and location of hangers are shown in Table 5.1 and Table 5.2. 5.2.3 The space (A) in Table 5.1 shall always be on the side of the door opening toward which the door closes. This is the lower end when the track

37、is inclined. 5.2.4 Doors for openings in excess of 6 ft (1.8 m) in width shall require three hangers. 5.2.5 When the size of the door opening is not specied in Table 5.1 or Table 5.2, the proper interpolation shall be made for the bolt spacing in accordance with 5.2.6. 5.2.6 To determine the proper

38、spacings for track bolt holes where the track is for an opening of a width not specied in Table 5.1 or Table 5.2, add to each of the spacings (excepting dimension A given in the table) for an opening of the next smaller width in the table than that width under consideration, a value C obtained from

39、the formula: in which: C is the correction factor in inches or mm, D is the width (in inches or mm) of opening under consideration, d is the width (in inches or mm) of opening next smaller in table, and b is the number of bolts required by Table 5.1 and Table 5.2 for track for width opening of size

40、d. DECEMBER 15, 2008 UL 14B 8UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Table 5.1 Spacing for bolt holes in at track Size of opening Length of track Space A 1st bolt Space B 2nd bolt Space C 3rd bolt Space D 4th bolt Space E 5th bolt ft

41、 in (m) ft in (m) in (mm) in (mm) in (mm) in (mm) in (mm) 3 0 0.91 7 9 2.36 1-3/4 45 12- 1/4 310 24 610 26-1/2 675 26-3/4 680 3 3 0.99 8 3 2.52 1-3/4 45 12- 1/4 310 27 685 28 710 28-1/4 720 3 6 1.07 8 9 2.67 1-3/4 45 13- 1/4 340 28 710 30 760 30-1/4 770 3 9 1.14 9 3 2.82 1-3/4 45 13- 1/4 340 31 785

42、31-1/2 800 31-3/4 805 4 0 1.22 9 9 2.97 1-3/4 45 14- 1/4 360 32 815 33-1/2 850 33-3/4 855 4 3 1.30 10 3 3.12 1-3/4 45 14- 1/4 360 35 890 35 890 35-1/4 895 4 6 1.37 10 9 3.28 1-3/4 45 15- 1/4 385 36 915 37 940 37-1/4 945 4 9 1.45 11 3 3.43 1-3/4 45 15- 1/4 385 19-1/2 495 19- 1/2 495 38-1/2 980 5 0 1.

43、53 11 9 3.58 1-3/4 45 16- 1/4 415 20 510 20 510 40-1/2 1030 5 3 1.60 12 3 3.73 1-3/4 45 16- 1/4 415 21-1/2 545 21- 1/2 545 28 710 5 6 1.68 12 9 3.89 1-3/4 45 17- 1/4 440 22 560 22 560 30 760 5 9 1.75 13 3 4.04 1-3/4 45 17- 1/4 440 23-1/2 595 23- 1/2 595 31 785 6 0 1.83 13 9 4.19 1-3/4 45 18- 1/4 465

44、 24 610 24 610 32 815 6 3 1.91 14 3 4.34 1-3/4 45 12- 1/4 310 31-1/2 800 31- 1/2 800 31 785 6 6 1.98 14 9 4.50 1-3/4 45 12- 1/4 310 33 840 33 840 32 815 6 9 2.06 15 3 4.65 1-3/4 45 13- 1/4 340 33-1/2 850 33- 1/2 850 33 840 7 0 2.13 15 9 4.80 1-3/4 45 13- 1/4 340 35 890 35 890 34 865 7 3 2.21 16 3 4.

45、95 1-3/4 45 14- 1/4 360 35-1/2 900 35- 1/2 900 36 915 7 6 2.29 16 9 5.11 1-3/4 45 14- 1/4 360 37 940 37 940 37 940 7 9 2.36 17 3 5.26 1-3/4 45 14- 1/4 360 19-1/4 490 19- 1/4 490 19-1/4 490 8 0 2.44 17 9 5.41 1-3/4 45 14- 1/4 360 20 510 20 510 20 510 8 3 2.52 18 3 5.56 1-3/4 45 14- 1/4 360 20-3/4 525

46、 20- 3/4 525 20-3/4 525 8 6 2.59 18 9 5.72 1-3/4 45 14- 1/4 360 21-1/2 545 21- 1/2 545 21-1/2 545 8 9 2.67 19 3 5.87 1-3/4 45 14- 1/4 360 22-1/4 565 22- 1/4 565 22-1/4 565 DECEMBER 15, 2008 UL 14B 9 Table 5.1 Continued on Next PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DI

47、STRIBUTION WITHOUT PERMISSION FROM UL Table 5.1 Continued Size of opening Length of track Space A 1st bolt Space B 2nd bolt Space C 3rd bolt Space D 4th bolt Space E 5th bolt ft in (m) ft in (m) in (mm) in (mm) in (mm) in (mm) in (mm) 9 0 2.74 19 9 6.02 1-3/4 45 14- 1/4 360 23 585 23 585 23 585 9 3

48、2.82 20 3 6.17 1-3/4 45 15- 1/4 385 23-1/4 590 23- 1/4 590 23-1/4 590 9 6 2.90 20 9 6.33 1-3/4 45 15- 1/4 385 24 610 24 610 24 610 9 9 2.97 21 3 6.48 1-3/4 45 16- 1/4 415 24-1/4 615 24- 1/4 615 24-1/4 615 10 0 3.05 21 9 6.63 1-3/4 45 16- 1/4 415 25 635 25 635 25 635 10 3 3.12 22 3 6.78 1-3/4 45 17-

49、1/4 440 25-1/4 640 25- 1/4 640 25-1/4 640 10 6 3.20 22 9 6.93 1-3/4 45 17- 1/4 440 26 660 26 660 26 660 10 9 3.28 23 3 7.09 1-3/4 45 18- 1/4 465 26-1/4 665 26- 1/4 665 26-1/4 665 11 0 3.35 23 9 7.24 1-3/4 45 18- 1/4 465 27 685 27 685 27 685 11 3 3.43 24 3 7.39 1-3/4 45 19- 1/4 490 27-1/4 690 27- 1/4 690 27-1/4 690 11 6 3.51 24 9 7.54 1-3/4 45 19- 1/4 490 28-1/2 725 28- 1/2 725 28-1/2 725 11 9 3.58 25 3 7.70 1-3/4 45

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > 其他

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1