1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 567B Emergency Breakaway Fittings, Swivel Connectors and Pipe-Connection Fittings for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends with Nominal Biodiesel Concentrations up to 20 Perc
2、ent (B20), Kerosene, and Fuel OilUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Emergency Breakaway Fitting
3、s, Swivel Connectors and Pipe-Connection Fittings for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends with Nominal Biodiesel Concentrations up to 20 Percent (B20), Kerosene, and Fuel Oil, UL 567B First Edition, Dated March 5, 2015 Summary of Topics This revision of ANSI/UL 567B relocates 9.1 to
4、 the scope section and revises the Moist Ammonia-Air Stress Cracking Test. The requirements are substantially in accordance with Proposal(s) on this subject dated May 1, 2015. Text that has been changed in any manner or impacted by ULs electronic publishing system is marked with a vertical line in t
5、he margin. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any k
6、ind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other
7、 damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim
8、. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing
9、an electronic Standard on the purchasers computer system. JUNE 17, 2015 UL 567B tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JUNE 17, 2015 UL 567B tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION
10、OR DISTRIBUTION WITHOUT PERMISSION FROM UL March 5, 2015 (Title Page Reprinted: June 17, 2015) 1 UL 567B Standard for Emergency Breakaway Fittings, Swivel Connectors and Pipe- Connection Fittings for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends with Nominal Biodiesel Concentrations up to 20
11、Percent (B20), Kerosene, and Fuel Oil Prior to the rst edition, the requirements for the products covered by this standard were included in the Outline of Investigation for Emergency Breakaway Fittings, Swivel Connectors and Pipe-Connection Fittings for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel
12、Blends with Nominal Biodiesel Concentrations up to 20 Percent (B20), Kerosene, and Fuel Oil, UL 567B. First Edition March 5, 2015 This ANSI/UL Standard for Safety consists of the First Edition including revisions through June 17, 2015. The most recent designation of ANSI/UL 567B as an American Natio
13、nal Standard (ANSI) occurred on June 17, 2015. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted
14、 via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regard
15、ing those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2015 UNDERWRITERS LABORATORIES INC. ANSI/UL 567B-2015UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JUNE 17, 2015 UL 567B 2 No Text on This PageUL COPYRIGHTED
16、 MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .5 2 General 6 2.1 Components .6 2.2 Units of measurement .6 2.3 Undated references .6A 3 Glossary .7 CONSTRUCTION 4 General 8 5 Materials .8 5.1 Metallic materials .8 5.2 Nonme
17、tallic materials .9 5.3 Casting impregnation materials 12 5.4 Internal parts .12 6 Swivel Connectors and Emergency Breakaway Fittings .12 7 Pipe-Connecting Fittings 13 8 End Connections 14 9 Hose Assemblies 17 PERFORMANCE 10 General 17 11 Long Term Exposure Test .19 11.1 General .19 11.2 Samples 19
18、11.3 Method .20 11.4 Results .20 12 Electrical-Continuity Test 21 12.1 General .21 12.2 Electrical continuity measurement 21 12.3 Electrical continuity alternate method .21 13 External Leakage Test 21 14 Seat Leakage Test 22 15 Operation Test .22 16 Endurance Test 24 17 Abuse Test 25 18 Drop Test 26
19、 19 Hydrostatic Strength Test 26 20 Pull Test .27 20.1 Pipe-connecting tting 27 20.2 Emergency breakaway tting 27 21 Marking Adhesion Test 28 22 Moist Ammonia-Air Stress Cracking Test 28 MANUFACTURING AND PRODUCTION 23 General 28A JUNE 17, 2015 UL 567B 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FUR
20、THER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INSTALLATION AND OPERATING INSTRUCTIONS 24 General 28B MARKING 25 General 28B SUPPLEMENT SA - Test Fluids SA.1 Representative Aggressive Combustible Test Fuel Mixtures SA1 JUNE 17, 2015 UL 567B 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR F
21、URTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These requirements cover emergency breakaway ttings, swivel connectors and pipe-connecting ttings of the threadless compression type. Connectors and ttings covered by these requirements are intended only for the
22、following services. 1.2 A swivel connector is either a hose swivel or joint swivel. The swivel connector will allow radial movement and shall be constructed for use with the uids shown in 1.4. 1.3 An emergency breakaway tting is used between the outlet of the dispensing device and the hose nozzle va
23、lve and separates in the event that the coupling is subjected to an excessive pull force to safeguard against abnormally excessive pull force on the hose assembly and dispenser and prevent loss of liquid. An emergency breakaway tting shall be constructed for use with the uids shown in 1.4. The tting
24、s shall be of the single-break or reconnectable type. 1.4 Emergency breakaway ttings, swivel connectors, and pipe-connecting ttings are intended for use with one or more of the following as applicable: a) Diesel fuel and diesel/biodiesel blends with nominal biodiesel concentrations up to 5 percent (
25、B0 B5) formulated in accordance with the Standard Specication for Diesel Fuel Oils, ASTM D975; b) Diesel/biodiesel blends with nominal biodiesel concentrations from 5 percent up to 20 percent (B6 B20) formulated in accordance with the Standard Specication for Diesel Fuel Oil, Biodiesel Blends (B6 B2
26、0), ASTM D7467; c) Biodiesel (B99.9/B100) formulated in accordance with the Standard Specication for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels, ASTM D6751; d) Kerosene formulated in accordance with the Standard Specication for Kerosine, ANSI/ ASTM D3699; or e) Fuel oil (heating o
27、il) formulated in accordance with the Standard Specication for Fuel Oils, ASTM D396. 1.5 Requirements for the installation and use of dispensing equipment handling the fuels described in 1.4 are included in the Flammable and Combustible Liquids Code, ANSI/NFPA 30, and the Code for Motor Fuel Dispens
28、ing Facilities and Repair Garages, ANSI/NFPA 30A. 1.6 These requirements do not cover devices intended for use with diesel, biodiesel, diesel/biodiesel blends, kerosene or fuel oil, which are covered under the Standard for Emergency Breakaway Fittings, Swivel Connectors, and Pipe-Connection Fittings
29、 for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 E85), UL 567A. MARCH 5, 2015 UL 567B 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 1.7 These requirements do not cover devices intended for
30、 use with LP-Gas or anhydrous ammonia, which are covered under the Standard for Emergency Breakaway Fittings, Swivel Connectors, and Pipe-Connection Fittings for Petroleum Products and LP-Gas, UL 567. 1.8 A hose assembly provided with a swivel connector or emergency breakaway tting for use with fuel
31、s anticipated by these requirements shall comply with the applicable requirements in the Standard for Hose and Hose Assemblies for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends with Nominal Biodiesel Concentrations up to 20 Percent (B20), Kerosene, and Fuel Oil, UL 330B. 2 General 2.1 Compone
32、nts 2.1.1 Except as indicated in 2.1.2, a component of a product covered by this standard shall comply with the requirements for that component. 2.1.2 A component is not required to comply with a specic requirement that: a) Involves a feature or characteristic not required in the application of the
33、component in the product covered by this standard, or b) Is superseded by a requirement in this standard. 2.1.3 A component shall be used in accordance with its rating established for the intended conditions of use. 2.1.4 Specic components are incomplete in construction features or restricted in per
34、formance capabilities. Such components are intended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and shall be used only under those specic conditions. 2.2 Units of measurement 2.2.1 Values stated without parentheses are the requirement. Values in
35、parentheses are explanatory or approximate information. JUNE 17, 2015 UL 567B 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 2.3 Undated references 2.3.1 Any undated reference to a code or standard appearing in the requirements of this sta
36、ndard shall be interpreted as referring to the latest edition of that code or standard. JUNE 17, 2015 UL 567B 6AUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JUNE 17, 2015 UL 567B 6B No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZ
37、ED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 3 Glossary 3.1 For the purpose of this standard, the following denitions apply. 3.2 DIESEL/BIODIESEL BLENDS Blended fuels composed of a diesel component and a biodiesel component. The numerical value corresponding to the biodiese
38、l component determines the blend rating (such as B20 for 20 percent biodiesel, 80 percent diesel). 3.3 FITTING, PIPE-CONNECTING A tting of the threadless compression seal-ring type for use in the assembly of dispensing devices to facilitate connection of piping or tubing. These ttings shall be made
39、in the straight coupling style, as well as in the tee, ell, reducer, adapter, and other styles. 3.4 FITTING, RECONNECTABLE TYPE An emergency breakaway tting designed such that upon separation it is intended to be reconnected and reused when it is not damaged. 3.5 FITTING, SINGLE-BREAK TYPE An emerge
40、ncy breakaway tting that, upon separation, is not intended to be reconnected and reused. 3.6 HOSE SWIVEL A swivel connector with one end attached to a hose and the other end to an appurtenance. The hose swivel will allow radial movement of the hose and/or appurtenance to prevent the hose from twisti
41、ng or having torsional stress. 3.7 PRESSURE INDICATING DEVICE As used herein, the pressure indicating device means one of the following: a) An analog gauge having a pressure range such that the test pressure is between 30 and 70 percent of the maximum scale reading of the gauge; b) A digital pressur
42、e transducer, or other digital gauge, that is calibrated over a range of pressure that includes the test pressure; or c) Other device that is equivalent to the devices in (a) or (b). 3.8 SEALS, DYNAMIC A seal that is subject to mechanical movement or other applied forces that result in movement or e
43、xing of the seal under normal use conditions. 3.9 SEALS, STATIC A seal that is not subject to mechanical movement or other applied forces other than compressing forces that are applied during installation, after which, the seal is held in place during normal use conditions. 3.10 SWIVEL CONNECTOR A t
44、ype of swivel categorized as either a hose swivel or swivel joint. 3.11 SWIVEL JOINT A swivel connector installed in a piping system with at least one end attached to a rigid pipe or other appurtenance that is rmly affixed. The swivel joint will allow radial movement of the pipe or other appurtenanc
45、e attached to the swivel to prevent torsional stress. MARCH 5, 2015 UL 567B 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONSTRUCTION 4 General 4.1 A connector or tting shall be constructed for an operating pressure of not less than 50 p
46、ounds per square inch gauge (psig) (340 kPa) for the uid conning portion of the device and 0.5 psig (3.45 kPa) for the vapor conning portion of the device, when provided, and an ultimate rupture pressure of not less than ve times the design pressure. 4.2 An emergency breakaway tting shall be constru
47、cted to separate in the event that the coupling is subjected to a pull force not less than 100 pounds (445 N), and not to exceed 350 pounds (1557 N). 5 Materials 5.1 Metallic materials 5.1.1 General 5.1.1.1 A metallic part, in contact with the fuels anticipated by these requirements, shall be resist
48、ant to the action of the fuel if degradation of the material will result in leakage of the fuel or if it will impair the function of the device. See the Long Term Exposure Test, Section 11. 5.1.1.2 The exposed surfaces of metallic parts shall be resistant to atmospheric corrosion if this corrosion w
49、ill lead to leakage of the uid or if it will impair the function of the device. The material shall comply with the requirements in Atmospheric corrosion, 5.1.2. 5.1.1.3 Metallic parts in contact with the fuels anticipated by these requirements shall not be constructed of lead, or materials that are substantially lead. In addition, no coatings or platings containing lead shall be used, such as terne-plated steel. 5.1.1.4 With reference to the above requirements, metallic p
