1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 83 Thermoplastic-Insulated Wires and Cables STANDARD FOR SAFETYUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERI
2、AL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Thermoplastic-Insulated Wires and Cables, UL 83 Sixteenth Edition, Dated July 28, 2017 Summary of Topics: This New Edition of ANSI/UL 83 includes: Changes to the Reference Publications in
3、 2.2. Revised 4.1.5.1 to clarify the information found in Table 1. Addition of a new subheading 4.1.5.2.2, Concentric, to dene a conventional concentric conductor. Revised 4.1.5.2.6 to permit compressed unilay single input to have other than reversed direction of strand layers. As a result, the titl
4、e of Table 7 revised. Addition of a reference to the Length of Lay test in UL 2556, CSA C22.2 No. 2556, or NMX-556-ANCE at 4.1.5.2.6 to specify how to determine the length of lay. Revised 4.1.6.1 to clarify that diameter requirements for conductor classes not referenced in Tables49donotneed to be de
5、ned. Added 4.1.7.1 to allow butt splices in sizes smaller than an 8 AWG conductor. Added a country deviation to 4.2.2, to clarify in Mexico, repairs on nished conductors are not permitted. Revised 4.2.4 to align with the description of the requirements in Table 10. Revised 5.2.1, 5.2.2, 5.3.1.2, 5.3
6、.2, and 5.13 to align with the Standard for Thermoset-Insulated Wires and Cables, UL 44/CSA C22.2 No. 38/NMX-J-451 Revised 5.3.1.2 to cover cases where the center strand consists of more than one wire and situations for non-compliance. Revised 5.5 and 5.6 for clearer interpretation of the LTIR test
7、procedure and stability requirements in Long Term Insulation Resistance and stability acceptance criteria. Tolerances are being added to immersion temperatures specied in 5.5.2 and 5.7 and to remove temperatures expressed in Fahrenheit. Revised Heat Shock, Cold Bend, FT1, Vertical Tray, and Oil Resi
8、stance tests and addition of new tables 27 and 28 (and subsequent tables renumbered) for deep-well submersible pump cable requirements. Revised Vertical specimen test in 5.12.3.1.1 to clarify the requirements apply only to the vertical ame aspect of the test, not the horizontal ame portion. Revised
9、5.12.7.2 to remove specications to the preparation of specimens since it is addressed in the referenced Standard for Wire and Cable Test Methods, UL 2556, CSA C22.2 No. 2556, or NMX-J-474-ANCE. JULY 28, 2017 UL 83 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WIT
10、HOUT PERMISSION FROM UL Revised optional weather resistance test in 5.13 based on World Resources Institute data on typical daily sunlight exposure in Canada can be reduced to 720 hours. Revised oil resistance at 60C and 75C tests in 5.14.1 and 5.14.2 to indicate that a wire that complies with the r
11、equirements for PR II must also comply with those for PR I. Revised optional marking requirement for Gasoline and Oil Resistance in 5.15.1 to specify the marking is only for wet rated conductors. Revised 5.18 to state the maximum number of specimens that are permitted to fail. Addition of a referenc
12、e to Table 4, Diameters over solid conductors and cross-sectional area for all solid and stranded conductors, to 6.1.4 to ensure the correct mm 2 value is marked. Addition of 6.1.5 to specify that wire is required to be marked when other than those with ASTM Class B, C or SIW stranding. Revised 6.1.
13、10.1(d) to add FT4IEEE 1202 marking as an option. Addition of Note to 6.1.10 to show it is a requirement in Canada that wires must be marked FT1 or FT4. Table C1 in Annex C is also revised. Addition of a note to indicate in Canada, the -40C rating is required as specied in the Canadian Electrical Co
14、de, Part I. As a result, 7.3.1, 7.3.2, and 7.4.4 have also been revised. Revised footnotes to Table 2 for clarity. Revised Table 7 title as a result of revision to 4.1.5.2.6. Additionally, the diameters for sizes 12-2 AWG from ASTM B 901 are being added, with a note that these apply to SIW only. Rev
15、ised Table 30 to correct the value for 3.31 mm 2 (12 AWG) for Types THWN-2, THWN. THHN and T90 Nylon in M1000 ft. Additionally, the footnotes have been revised so that K values are expressed in both M1000 ft and Gm. Revised Table 34 to clarify that any jacket thickness is acceptable. Globally revise
16、d all instances of nylon covering to nylon jacket for consistency throughout the standard based on the NEC and the Canadian Electrical Code, Part I; Revisions to specify the jacket tests from the thermoset standard to the multi-conductor construction of the circuit conductors in the thermoplastic st
17、andard for consistency for jacket requirements for deep-well submersible pump cables. The new and revised requirements are substantially in accordance with Proposal(s) on this subject dated July 1, 2016, and February 24, 2017. All rights reserved. No part of this publication may be reproduced, store
18、d in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranti
19、es of merchantability or tness for any purpose. JULY 28, 2017 UL 83 tr2UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of p
20、rots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this
21、 Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or de
22、viation introduced while purchaser is storing an electronic Standard on the purchasers computer system. JULY 28, 2017 UL 83 tr3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JULY 28, 2017 UL 83 tr4 No Text on This PageUL COPYRIGHTED MATERIA
23、L NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Association of Standardization and Certication NMX-J-010-ANCE-2017 Sixth Edition CSA Group CSA C22.2 No. 75-17 Eleventh Edition Underwriters Laboratories Inc. UL 83 Sixteenth Edition Thermoplastic-Insulated Wires an
24、d Cables July 28, 2017 ANSI/UL 83-2017UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Commitment for Amendments This standard is issued jointly by the Association of Standardization and Certication (ANCE), the Canadian Standards Association
25、(operating as CSA Group), and Underwriters Laboratories Inc. (UL). Comments or proposals for revisions on any part of the standard may be submitted to ANCE, CSA Group, or UL at any time. Revisions to this standard will be made only after processing according to the standards development procedures o
26、f ANCE, CSA Group, and UL. CSA Group and UL will issue revisions to this standard by means of a new edition or revised or additional pages bearing their date of issue. ANCE will incorporate the same revisions into a new edition of the standard bearing the same date of issue as the CSA Group and UL p
27、ages. Copyright 2017 ANCE Rights reserved in favor of ANCE. ISBN 9781488304330 2017 CSA Group All rights reserved. No part of this publication may be reproduced in any form whatsoever without the prior permission of the publisher. This Standard is subject to review ve years from the date of publicat
28、ion, and suggestions for its improvement will be referred to the appropriate committee. To submit a proposal for change, please send the following information to inquirescsagroup.org and include Proposal for change in the subject line: Standard designation (number); relevant clause, table, and/or gu
29、re number; wording of the proposed change; and rationale for the change. To purchase CSA Group Standards and related publications, visit CSA Groups Online Store at shop.csa.ca or call toll-free 1-800-463-6727 or 416-747-4044. Copyright 2017 Underwriters Laboratories Inc. ULs Standards for Safety are
30、 copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. This ANSI/UL Standard for Safety consists of the Sixteen
31、th Edition. The most recent designation of ANSI/UL 83 as an American National Standard (ANSI) occurred on July 28, 2017. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page (front and back), or the Preface. The National Difference Page and IEC Foreword are als
32、o excluded from the ANSI approval of IEC-based standards. TheDepartmentofDefense(DoD)hasadoptedUL 83 onFebruary27, 1984. Thepublication of revised pages or a new edition of this Standard will not invalidate the DoD adoption. Comments or proposals for revisions on any part of the Standard may be subm
33、itted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at https:/. To purchase UL Standards, visit ULs Standards Sales Site at http:/ HowToOrder.aspx or call toll-free 1-888-853-3503.UL COPYRIGHTED MATERIAL NOT A
34、UTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS PREFACE 6 1 Scope .8 2 General 8 2.1 Units of measure .8 2.2 Reference publications 9 2.3 Summary of requirements 12 2.4 General requirements 12 3 Denitions 12 4 Construction.12 4.1 Conductors .12 4.2 Insulation .
35、17 4.3 Nylon jacket 19 4.4 Assemblies that include thermoplastic-insulated single conductors.19 5 Test requirements19 5.1 General 19 5.2 Conductor resistance 20 5.3 Tests on aluminum conductors 20 5.4 Short-term insulation resistance at elevated temperature in water .21 5.5 Long-term insulation resi
36、stance in water acceptance criteria 21 5.6 Long-term insulation resistance in air for 90C rated conductors 22 5.7 Capacitance and relative permittivity of wet rated (W type) wires 23 5.8 Flexibility at room temperature after aging 23 5.9 Heat shock .23 5.10 Cold bend and cold impact 24 5.11 Deformat
37、ion .24 5.12 Flame and smoke 25 5.13 Weather (sunlight) resistance (optional) .28 5.14 Oil resistance (optional) .29 5.15 Gasoline and oil resistance (optional) .29 5.16 Abrasion resistance (nylon-jacketed types or insulations other than PVC) .30 5.17 Crush resistance (nylon-jacketed types or insula
38、tions other than PVC)30 5.18 Impact resistance (nylon-jacketed types or insulations other than PVC) .30 5.19 Durability of ink printing .30 5.20 Color coating 30 5.21 Long-term aging of insulation 31 5.22 A-C spark test .31 5.23 Dielectric voltage-withstand in water 31 5.24 Insulation resistance in
39、water at 15C.32 5.25 Electrical continuity .32 6 Marking.32 6.1 Marking on product 32 6.2 Marking on package .35 6.3 Month and year of manufacture 36 7 Deep-well submersible water pump cable .36 7.1 General 36 7.2 Construction 36 7.3 Marking 38 7.4 Tests 39 JULY 28, 2017 NMX-J-010-ANCE-2017 CSA C22.
40、2 NO. 75-17 UL 83 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Tables Annex A (informative) Wire Type and Electrical Code Cross-Reference and Summary of Applications Annex B (normative for Mexico) Multiple-Conductor Thermoplastic-Insulat
41、ed and -Jacketed Cables B1 Scope .71 B1.1 General .71 B1.2 Single conductors 71 B2 Lay of cabled conductors 71 B3 Equipment-grounding conductor 72 B4 Conductor identication .72 B4.1 Color of insulated grounding conductor .72 B4.2 Identication of ungrounded (phase) conductor(s) 72 B4.3 Identication o
42、f grounded conductor(s) .72 B5 Fillers .72 B6 Jacket separators.72 B7 Jackets72 B7.1 General .72 B7.2 Jacket thickness .73 B8 Marking .73 B8.1 Marking on product.73 B8.2 Marking on package 73 Annex C (informative) Summary of Requirements Annex D (normative) Chemical Composition of Recognized ACM or
43、AA 8000 Series Aluminum Alloy Conductor Materials Annex E (normative) Copper-Clad Aluminum Conductors E1 General .80 E2 Sizes and stranding.80 E3 Conductor resistance .80 E4 Physical properties .80 E5 Marking requirements .80 JULY 28, 2017 NMX-J-010-ANCE-2017 CSA C22.2 NO. 75-17 UL 83 4UL COPYRIGHTE
44、D MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Annex F (informative) Metric Sizes Annex G (informative) Evaluation of Materials Having Characteristics Differing from Those in Table 11 Annex H (informative) French and Spanish Translations and Markings H1
45、 General .86 H2 Markings on wire .86 H3 Markings on packaging86 JULY 28, 2017 NMX-J-010-ANCE-2017 CSA C22.2 NO. 75-17 UL 83 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL PREFACE This is the harmonized ANCE, CSA Group, and UL Standard for
46、Thermoplastic-Insulated Wires and Cables. It is the Sixth edition of NMX-J-010-ANCE, the Eleventh edition of CAN/CSA-C22.2 No. 75, and the Sixteenth edition of UL 83. This edition of NMX-J-010-ANCE supersedes the previous edition published March 28, 2014. This edition of CAN/CSA-C22.2 No. 75 superse
47、des the previous edition published March 28, 2014. This edition of UL 83 supersedes the previous edition published March 28, 2014. This harmonized standard was prepared by the Association of Standardization and Certication, (ANCE), CSA Group and Underwriters Laboratories Inc. (UL). The efforts and s
48、upport of the Technical Harmonization Committee for Electrical Wires and Cables, of the Council on the Harmonization of Electrotechnical Standards of the Nations of the Americas (CANENA), are gratefully acknowledged. This standard is considered suitable for use for conformity assessment within the s
49、tated scope of the standard. The present Mexican Standard was developed by the CT 20 Conductores from the Comite de Normalizacion de la Asociacion de Normalizacion y Certicacion, A.C., CONANCE, with the collaboration of the SC 20B Conductores para Baja Tensin. This standard was reviewed by the CSA Integrated Committee on Fixed Installation Wires and Cable, under the jurisdiction of the CSA Technical Committee on Wiring Products and the CSA Strate
