UNE 16-535-1991 《钳子和夹钳 木匠夹钳 测量和试验值》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

KS B ISO 2490-2008 Solid (monobloc) gear hobs with tenon drive or axial keyway 0 5 to 40 module－Nominal dimensions《模数0 5~40榫传动或轴键带动的单头螺纹滚齿刀 公称尺寸》.pdf

KS B ISO 2503-2007 Gas welding equipment-Pressure regulators for gas cylinders used in welding cutting and allied processes up to 300 bar《气焊设备 用于压力在300bar(30MPa)以下的焊接、切割及相关工艺的调压器和配.pdf

KS B ISO 2540-2013 Centre drills for centre holes with protecting chamfer－Type B《钻中心孔用有保护槽中心孔的中心钻 B型》.pdf

KS B ISO 2541-2013 Centre drills for centre holes with radius form－Type R《钻中心孔用有保护槽中心孔的中心钻 R型》.pdf

KS B ISO 2725-1-2002 Assembly tools for screws and nuts－Square drive sockets－Part 1：Hand－operated sockets－Dimensions《螺钉和螺母用装配工具 第1部分 手动扳手》.pdf

KS B ISO 2725-2-2002 Assembly tools for screws and nuts－Square drive sockets－Part 2：Machine－operated sockets(“impact”)－Dimensions《螺钉和螺母用装配工具 方头钻动扳手 第2部分 机动扳手尺寸》.pdf

KS B ISO 2725-3-2002 Assembly tools for screws and nuts－Square drive sockets－Part 3：Machine－operated sockets(“non－impact”)－Dimensions《螺钉和螺母用装配工具 方头传动套筒 第3部分 机动套筒(非撞击) 尺寸》.pdf

KS B ISO 273-2010 Diameter of clearance holes and counterbores for bolts and screws《螺栓孔与沉孔直径》.pdf

KS B ISO 2860-2012 Earth-moving machinery－Minimum access dimensions《土方机械 最小间距》.pdf