UNE 53-328-1985 《温室用低密度聚乙烯薄膜的特性及测试方法》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

DIN 3965-2-1986 Tolerancing of bevel gears tolerances for individual parameters《伞齿轮啮合公差 第2部分 专用参数公差》.pdf

DIN 3965-3-1986 Tolerancing of bevel gears tolerances for tangential composite errors《伞齿轮啮合公差 第2部分 正切组合误差用公差》.pdf

DIN 3965-4-1986 Tolerancing of bevel gears tolerances for shaft angle errors and axes intersection point deviations《伞齿轮啮合公差 第4部分 轴线夹角误差及轴线交叉点偏差用公差》.pdf

DIN 3966-1-1978 Information on Gear Teeth in Drawings Information on Involute Teeth for Cylindrical Gears《图纸上齿轮啮合信息 第1部分 圆柱齿轮渐开线啮合信息》.pdf

DIN 3966-2-1978 Information on Gear Teeth in Drawings Information on Straight Bevel Gear Teeth《图纸上齿轮啮合信息 第2部分 直齿伞齿轮啮合信息》.pdf

DIN 3967-1978 System of Gear Fits Backlash Tooth Thickness Allowances Tooth Thickness Tolerances Principles《齿轮配合体系 侧隙、齿厚容差和齿厚公差 原则》.pdf

DIN 3968-1960 Tolerances for Single-start Hobs for Involute Spur Gears《渐开线正齿轮用单头滚铣刀的公差》.pdf

DIN 3969-1-1991 Surface roughness of tooth flanks roughness parameters surface grades《齿面表面粗糙度 粗糙度参数 表面等级》.pdf

DIN 3970-2010 Master gears for checking cylindrical gears - Gear blanks and gearing《圆柱齿轮检查用标准齿轮 齿轮毛坯和齿轮传动》.pdf