UNE 7 117 《金属材料的疲劳试验，定义和符号》.pdf

相关资源

JIS Z 2201-1998 中文版 金属材料拉伸试验.pdf

JIS Z 2201-1998 英文版 金属材料抗拉试验用试样.pdf

JIS Z 2242-2005 金属材料冲击试验方法.pdf

JIS Z 2254-2008 中文版 薄板金属材料的塑性变形比试验方法.pdf

JIS Z 2254-2008 英文版 薄板金属材料的塑性变形比试验方法.pdf

JIS Z 3422-1-2003 金属材料焊接程序规范及认可.焊接程序试验.第1部分钢的电弧焊及气焊和镍及镍合金的电弧焊.pdf

JIS Z3420-2003 金属材料焊接过程的规范及认可.总则 Specification and approval of welding procedures for metallic materials -- Welding procedure specification for arc welding.pdf

JIS G0564-1999 金属材料.平面应变断裂强度的测定.pdf

JIS H7503-2003 超塑变形金属材料孔穴体积百分率的测量方法.pdf

YB T 5293-2006 金属材料.顶锻试验方法.pdf

猜你喜欢

NASA NACA-TN-1050-1946 Wind-tunnel investigation of end-plate effects of horizontal tails on a vertical tail compared with available theory《和可得的理论相比 水平尾翼对垂直尾翼端板影响的风洞研究》.pdf

NASA NACA-TN-1051-1946 Preliminary investigation of the loads carried by individual bolts in bolted joints《由螺栓结合中个体螺栓执行的荷载初步研究》.pdf

NASA NACA-TN-1071-1946 Wind-tunnel investigation of boundary-layer control by suction on the NACA 653-418 a = 1 0 airfoil section with a 0 29-airfoil-chord double slotted flap《带有0 .pdf

NASA NACA-TN-1110-1946 Two-dimensional wind-tunnel investigation of an approximately 14-percent-thick NACA 66-series-type airfoil section with a double slotted flap《带有双开缝襟翼且大约厚度为14.pdf

NASA NACA-TN-1113-1947 Collection and analysis of hinge-moment data on control-surface tabs《操纵面伺服片铰链力矩数据的采集和分析》.pdf

NASA NACA-TN-1174-1947 The application of high-temperature strain gages to the measurements of vibratory stresses in gas-turbine buckets《高温应变计对气体涡轮机叶片中振动性应力测量的应用》.pdf

NASA NACA-TN-1175-1947 Lifting-surface-theory aspect-ratio corrections to the lift and hinge-moment parameters for full-span elevators on horizontal tail surfaces《在水平尾翼面上全翼展电梯升力和铰链.pdf

NASA NACA-TN-1187-1947 Formulas for additional mass corrections to the moments of inertia of airplanes《附加质量更正和飞机惯性力矩的公式》.pdf

NASA NACA-TN-1191-1947 Two-dimensional wind-tunnel investigation of four types of high-lift flap on an NACA 65-210 airfoil section《NACA 65-210翼剖面上四种类型高升力襟翼的二维风洞研究》.pdf