1、10-11 08 56 19 - 1 SECTION 08 56 19 PASS WINDOWS SPEC WRITER NOTE: 1. Delete between / _ / if not applicable to project. 2. Also delete any other item or paragraph not applicable in the section and renumber the paragraphs. PART 1 - GENERAL 1.1 DESCRIPTION This section specifies sliding glass counter
2、 mounted pass windows. 1.2 RELATED WORK A. Color of factory finish: Section 09 06 00, SCHEDULE FOR FINISHES. B. Pass window opening: Section 08 33 13, COILING COUNTER DOORS. C. Glass and Glazing: Section 08 80 00, GLAZING. 1.3 APPLICABLE PUBLICATIONS A. Publications listed below form a part of this
3、specification to extend referenced. Publications are referenced in text by basic designation only. B. American Society for Testing and Materials (ASTM): B221/221M-08 . Aluminum and Aluminum- Alloy Extruded Bars, Rods, Wire, Shapes and Tubes (Metric) C509-06 Elastomeric Cellular Preformed Gasket and
4、Sealing Material C. American Society of Mechanical Engineers (ASME): B18.6.4-98(R2005) Thread Forming and Thread Cutting Tapping Screws and Metallic Drive Screws D. Master Painters Institute (MPI): MPI #18 Organic Zinc Rich Coating E. National Association of Architectural Metal Manufacturers (NAAMM)
5、 AMP 500 Series . Metal Finishes Manual AMP 500 Introduction to Metal Finishing AMP 501 Finishes for Aluminum PART 2 - PRODUCTS SPEC WRITER NOTE: 1. Make material requirements agree with applicable requirements specified in the referenced Applicable Publications. 2. Update and specify only that whi
6、ch applied to the project. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-10-11 08 56 19 - 2 2.1 MATERIAL A. Aluminum Extrusions: 1. ASTM B 221 M. 2. Alloy and temper recommended by window manufacturer for strength, corrosion resistance, and applica
7、tion of required finish, but not less than 150 MPa (22,000 psi) ultimate tensile strength, and yield of 110 MPa (16,000 psi). 3. Aluminum alloy used for colored anodic coating as required to produce specified color. B. Paint: MPI #18. C. Glazing Gaskets: ASTM C 509. 2.1 SLIDING GLASS PASS WINDOWS, C
8、OUNTER MOUNTED A. Fabricate sliding glass sash and frames of extruded aluminum with corners mitered. B. Fabricate sash to receive 6 mm (1/4 inch) thick glass. C. Fabricate sliding sash of “H“ channel molding at bottom edges including concealed nylon rollers at bottom set on track and guides at top s
9、et into track. D. Provide sash with pin tumbler lock and two keys. E. Provide sash with finger slot on vertical edge. F. Fabricate frame with channel sash slot, bottom roller track, and top guides. G. Sash may be factory or field glazed using glazing gaskets. H. Use concealed screws in assembly. I.
10、Finish: 1. Comply with NAAMM AMP 500 Series. 2. Clear anodic coating, Class II Architectural 0.4 mills thick, AA-C22A41. 3. Colored anodic coating, Class II, Architectural, 0.4 mills thick, AA-C22A42. PART 3 - EXECUTION 3.1 INSTALLATION A. Install in pass window opening level and plumb. B. Secure wi
11、th screws to opening; ASME B18.6.4. 1. Screw within 100 mm (4 inches) of ends. 2. Space screws not over 600 mm (24 inches) between end screws. C. Coat aluminum in contact with steel with one coat of MPI No. 18. D. Clean unit of dust and markings. Provided by IHSNot for ResaleNo reproduction or netwo
12、rking permitted without license from IHS-,-,-10-11 08 56 19 - 3 3.2 OPERATION A. Adjust to roll smoothly and stay in position where stopped. B. Demonstrate to Resident Engineer operation and locking. C. Turn keys with key tags over to Resident Engineers. - - E N D - - - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
