VDA 675-131-2016 No English Title.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

AGMA 08FTM19-2008 How Are You Dealing with the Bias Error in Your Helical Gears 《您如何处理斜齿轮的偏移误差？》.pdf

AGMA 09FTM01-2009 Influence of the Residual Stresses Induced by Hard Finishing Processes on the Running Behavior of Gears《在齿轮转动时由硬齿面精加工产生的残余应力的影响》.pdf

AGMA 09FTM02-2009 Implementing ISO 18653 Gears - Evaluation of Instruments for the Measurement of Individual Gears《实施ISO 18653标准 齿轮.单个齿轮测量用仪器评估》.pdf

AGMA 09FTM03-2009 Producing Profile and Lead Modifications in Threaded Wheel and Profile Grinding《螺纹大齿轮和轮廓磨削中的生产齿廓和齿向修正》.pdf

AGMA 09FTM04-2009 New Developments in Gear Hobbing《齿轮滚刀加工的新发展》.pdf

AGMA 09FTM05-2009 Hypoloid Gears with Small Shaft Angles and Zero to Large Offsets《小轴间角和偏心距大于零的双曲线齿轮》.pdf

AGMA 09FTM06-2009 Dependency of the Peak-to-Peak-Transmission-Error on the Type of Profile Correction and the Transverse Contact Ratio of the Gear Pair《齿轮副轮廓修形和端面啮合度峰到峰传输错误的相关性》.pdf

AGMA 09FTM07-2009 Optimizing Gear Geometry for Minimum Transmission Error Mesh Friction Losses and Scuffing Risk Through Computer Aided Engineering《通过计算机辅助工程优化齿轮的最小传输错误、啮合摩擦损耗和胶合风险.pdf

AGMA 09FTM08-2009 Load Sharing Analysis of High Contact Ratio Spur Gears in Military Tracked Vehicle Application《军用履带车辆上高啮合系数直齿轮的负载共享分析》.pdf