GA 222-2009 REPAIRING SCREW OR NAIL POPS《螺钉或钉支撑物的维修》.pdf

上传人:ideacase155 文档编号:1228954 上传时间:2019-08-11 格式:PDF 页数:2 大小:91.20KB
下载 相关 举报
GA 222-2009 REPAIRING SCREW OR NAIL POPS《螺钉或钉支撑物的维修》.pdf_第1页
第1页 / 共2页
GA 222-2009 REPAIRING SCREW OR NAIL POPS《螺钉或钉支撑物的维修》.pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、GA-222-09 Copyright Gypsum Association 2009. All rights reserved. Printed in U.S.A. REPAIRING SCREW OR NAIL POPS (GA-222-09) The protrusion of screw or nail heads above the gypsum panel surface is caused by one or more of the following: Lumber shrinkage occurring after gypsum panel product applicati

2、on, Loose attachment of the gypsum panel product to the framing, Improperly aligned, twisted, bent, warped, or bowed framing, Incorrect fastener length, or Improper fastening Fastener pops are largely caused by lumber shrinkage due to initially high moisture content lum-ber. Overly long fastener len

3、gth contributes to the problem and fastener penetration into wood fram-ing should not exceed 7/8 in. (22 mm) for nails, 5/8 in. (16 mm) for screws. For fire-resistance rated systems use fastener lengths specified in the listing. Fastener pops that appear either before or during decoration should be

4、repaired immediately. Those that appear one or more months into the heating season are usually a result of lumber shrink-age and should not be repaired until the end of the heating season. Fastener pops are repaired by reattaching the gypsum panel product to the framing by driving a new screw or nai

5、l of the proper length into the same framing member about 1-1/2 in. (40 mm) from the popped fastener. Apply sufficient pressure to the gypsum panel to bring the back surface into firm contact with the framing member to which it is being reattached. Remove the fastener or reseat the popped fastener s

6、o that it is just below the face of the gypsum panel. Remove any loose material before treating with joint compound and redecorating. GA-222-09 Copyright Gypsum Association 2009. All rights reserved. Printed in U.S.A. GYPSUM ASSOCIATION 6525 Belcrest Road, #480 Hyattsville, MD 20782 301-277-8686 Fax

7、 202-277-8747 www.gypsum.org MEMBER COMPANY LIST 2009 AMERICAN GYPSUM COMPANY LLC CERTAINTEED GYPSUM, INC. CERTAINTEED GYPSUM CANADA, INC. CGC INC. GEORGIA-PACIFIC GYPSUM LLC LAFARGE NORTH AMERICA INC. NATIONAL GYPSUM COMPANY PABCOGYPSUM a division of PABCObuilding products, LLC TEMPLE-INLAND UNITE

8、D STATES GYPSUM COMPANY This document may be revised or withdrawn from circulation at any time. The status of the document should be verified by the user prior to following any recommendations contained herein. To verify that you have the most current edition of the docu-ment, access the Gypsum Association website at: www.gypsum.org.

展开阅读全文
相关资源
猜你喜欢
  • NF C46-922-1997 Telecontrol equipment and systems Part 2  operating conditions Section 2  environmental conditions (climatic mechanical and other non-electrical influences) 《遥控设备和系.pdf NF C46-922-1997 Telecontrol equipment and systems Part 2 operating conditions Section 2 environmental conditions (climatic mechanical and other non-electrical influences) 《遥控设备和系.pdf
  • NF C46-951-02-1996 Telecontrol equipment and systems Part 5  transmission protocols Section 102  companion standard for the transmission of integrated totals in electric power syst.pdf NF C46-951-02-1996 Telecontrol equipment and systems Part 5 transmission protocols Section 102 companion standard for the transmission of integrated totals in electric power syst.pdf
  • NF C46-951-03-1998 Telecontrol equipment and systems Part 5-103  transmission protocols Companion standard for the informative interface of protection equipment 《遥控设备和系统 第5-103部分 传.pdf NF C46-951-03-1998 Telecontrol equipment and systems Part 5-103 transmission protocols Companion standard for the informative interface of protection equipment 《遥控设备和系统 第5-103部分 传.pdf
  • NF C46-951-04-2007 Telecontrol equipment and systems - Part 5-104  transmission protocols - Network access for IEC 60870-5-101 using standard transport profiles 《遥控设备和系统 第5-104部分 传.pdf NF C46-951-04-2007 Telecontrol equipment and systems - Part 5-104 transmission protocols - Network access for IEC 60870-5-101 using standard transport profiles 《遥控设备和系统 第5-104部分 传.pdf
  • NF C46-951-1993 Telecontrol equipment and systems Part 5  transmission protocols Section one  transmission frame formats 《遥控设备及系统 第5部分 传输协议 第1单元 传输框架格式》.pdf NF C46-951-1993 Telecontrol equipment and systems Part 5 transmission protocols Section one transmission frame formats 《遥控设备及系统 第5部分 传输协议 第1单元 传输框架格式》.pdf
  • NF C46-952-1993 Telecontrol equipment and systems Part 5  transmission protocols Section 2  link transmission procedures 《遥控设备及装置 第5部分 传输协议 第2节 链接传输程序》.pdf NF C46-952-1993 Telecontrol equipment and systems Part 5 transmission protocols Section 2 link transmission procedures 《遥控设备及装置 第5部分 传输协议 第2节 链接传输程序》.pdf
  • NF C46-953-1993 Telecontrol equipment and systems Part 5  transmission protocols Section 3  general structure of application data 《遥控设备和系统 第5部分 传输协议 第3节 应用数据的一般结构》.pdf NF C46-953-1993 Telecontrol equipment and systems Part 5 transmission protocols Section 3 general structure of application data 《遥控设备和系统 第5部分 传输协议 第3节 应用数据的一般结构》.pdf
  • NF C46-954-1994 Telecontrol equipment and systems Part 5  transmission protocols Section 4  definition and coding of application information elements 《遥控设备及系统 第5部分 传输协议 第4节 应用信息元件的.pdf NF C46-954-1994 Telecontrol equipment and systems Part 5 transmission protocols Section 4 definition and coding of application information elements 《遥控设备及系统 第5部分 传输协议 第4节 应用信息元件的.pdf
  • NF C46-955-1995 Telecontrol equipment and systems Part 5  transmission protocols Section 5  bais application functions 《遥控设备和系统 第5部分 传输协议 第5节 基本应用功能》.pdf NF C46-955-1995 Telecontrol equipment and systems Part 5 transmission protocols Section 5 bais application functions 《遥控设备和系统 第5部分 传输协议 第5节 基本应用功能》.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 行业标准 > GA公共安全

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1