1、INTERNATIONAL STANDARD IEC 60393-6-1 First edition 2003-05 Potentiometers for use in electronic equipment Part 6-1: Blank detail specification: Surface mount preset potentiometers Assessment level E Reference number IEC 60393-6-1:2003(E)Publication numbering As from 1 January 1997 all IEC publicatio
2、ns are issued with a designation in the 60000 series. For example, IEC 34-1 is now referred to as IEC 60034-1. Consolidated editions The IEC is now publishing consolidated versions of its publications. For example, edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the base publication, the ba
3、se publication incorporating amendment 1 and the base publication incorporating amendments 1 and 2. Further information on IEC publications The technical content of IEC publications is kept under constant review by the IEC, thus ensuring that the content reflects current technology. Information rela
4、ting to this publication, including its validity, is available in the IEC Catalogue of publications (see below) in addition to new editions, amendments and corrigenda. Information on the subjects under consideration and work in progress undertaken by the technical committee which has prepared this p
5、ublication, as well as the list of publications issued, is also available from the following: IEC Web Site (www.iec.ch) Catalogue of IEC publications The on-line catalogue on the IEC web site (http:/www.iec.ch/searchpub/cur_fut.htm) enables you to search by a variety of criteria including text searc
6、hes, technical committees and date of publication. On-line information is also available on recently issued publications, withdrawn and replaced publications, as well as corrigenda. IEC Just Published This summary of recently issued publications (http:/www.iec.ch/online_news/ justpub/jp_entry.htm) i
7、s also available by email. Please contact the Customer Service Centre (see below) for further information. Customer Service Centre If you have any questions regarding this publication or need further assistance, please contact the Customer Service Centre: Email: custserviec.ch Tel: +41 22 919 02 11
8、Fax: +41 22 919 03 00INTERNATIONAL STANDARD IEC 60393-6-1 First edition 2003-05 Potentiometers for use in electronic equipment Part 6-1: Blank detail specification: Surface mount preset potentiometers Assessment level E IEC 2003 Copyright - all rights reserved No part of this publication may be repr
9、oduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commission, 3, rue de Varemb, PO Box 131, CH-1211 Geneva 20, Switzerland Telephone: +41 22 919 02 11 Telefa
10、x: +41 22 919 03 00 E-mail: inmailiec.ch Web: www.iec.ch N For price, see current catalogue PRICE CODE Commission Electrotechnique Internationale International Electrotechnical Commission 2 60393-6-1 IEC:2003(E) INTERNATIONAL ELECTROTECHNICAL COMMISSION _ POTENTIOMETERS FOR USE IN ELECTRONIC EQUIPME
11、NT Part 6-1: Blank detail specification: Surface mount preset potentiometers Assessment level E FOREWORD 1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of
12、 the IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, the IEC publishes International Standards. Their preparation is entrusted to technical committees; any IEC National
13、Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization for Standardization (IS
14、O) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representati
15、on from all interested National Committees. 3) The documents produced have the form of recommendations for international use and are published in the form of standards, technical specifications, technical reports or guides and they are accepted by the National Committees in that sense. 4) In order t
16、o promote international unification, IEC National Committees undertake to apply IEC International Standards transparently to the maximum extent possible in their national and regional standards. Any divergence between the IEC Standard and the corresponding national or regional standard shall be clea
17、rly indicated in the latter. 5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with one of its standards. 6) Attention is drawn to the possibility that some of the elements of this International Standar
18、d may be the subject of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60393-6-1 has been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipment. The text of this standard is based on t
19、he following documents: FDIS Report on voting 40/1289/FDIS 40/1325/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This Blank D
20、etail Specification is to be used in conjunction with IEC 60393-1:1989 and IEC 60393-6:2003. The committee has decided that the contents of this publication will remain unchanged until 2008. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. A bi
21、lingual version of this publication may be issued at a later date.60393-6-1 IEC:2003(E) 3 POTENTIOMETERS FOR USE IN ELECTRONIC EQUIPMENT Part 6-1: Blank detail specification: Surface mount preset potentiometers Assessment level E INTRODUCTION Blank Detail Specification A Blank Detail Specification i
22、s a supplementary document to the Sectional Specification and contains requirements for style, layout and minimum content of Detail Specifications. Detail Specifications not complying with these requirements are not to be considered as being in accordance with IEC Specifications nor are they to be s
23、o described. In the preparation of Detail Specifications, the content of 1.4 of IEC 60393-6 is to be taken into account. The numbers between square brackets on the first page correspond to the following information which is to be inserted in the position indicated. Identification of the Detail Speci
24、fication 1 The “International Electrotechnical Commission” or the National Standard Organization under whose authority the Detail Specification is drafted. 2 The IEC or National Standards number of the Detail Specification, date of issue and any further information required by the national system. 3
25、 The number and issue number of the IEC or national Generic Specification. 4 The IEC number of the Blank Detail Specification. Identification of the potentiometer 5 A short description of the type of potentiometer. 6 Information on typical construction (if applicable) for example: non-wirewound, lea
26、d- screw actuated. 7 Outline drawing with main dimensions which are of importance for interchangeability and/or reference to the national or international documents for outlines. Alternatively, this drawing may be given in an annex to the Detail Specification. 8 Application or group of applications
27、covered and/or assessment level. 9 Reference data on the most important properties, to allow comparison between the various potentiometer types. 4 60393-6-1 IEC:2003(E) 1 IEC 60393-6-1-XXX 2 QC 410501XXXXXX ELECTRONIC COMPONENTS OF ASSESSED QUALITY IN ACCORDANCE WITH : IEC 60393-6-1 4 QC 410501 3 Ou
28、tline drawing and dimensions: ( angle projection) SURFACE MOUNT 5 PRESET POTENTIOMETERS 7 (When necessary the dimensions may be given in annex to the Detail Specification) Typical construction: 6 Terminal connections: Assessment level: E 8 For 1 to 9, see the Introduction. 9 Table 1 Important proper
29、ties Insulation voltage (DC or AC peak) V Style Rated dissipation at 70 C W Limiting element voltage (DC or AC r.m.s.) V Normal air pressure Low air pressure 1 General data 1.1 Recommended method(s) of mounting (to be inserted) (See 1.4.2 of IEC 60393-6). 1.2 Dimensions (When necessary, the dimensio
30、ns may be given in an annex to the Detail Specification). All dimensions are in millimetres. Information on the availability of components qualified to this Detail Specification is given in the register of approvals.60393-6-1 IEC:2003(E) 5 1.3 Ratings and characteristics Resistance range 1. to . Tol
31、erances on rated resistance . % Resistance law (if other than linear) . Temperature characteristic of resistance (20 C to 70 C) R/R . % Temperature coefficient . 10 -6 /K Climatic category -/-/- Low air pressure 8 kPa Limits of resistance change ( . % R + . ) (after 500 h or 1 000 h electrical endur
32、ance test) Starting torque . mN.m to . mN.m Total mechanical travel . . turns or . Limiting moving contact current . mA 1.3.1 Derating Potentiometers covered by this Specification are derated according to the following curve: (A suitable curve to be included in the Detail Specification) NOTE See als
33、o 2.2.3 of IEC 60393-6. 1.4 Normative references Generic Specification: IEC 60393-1:1989, Potentiometers for use in electronic equipment Part 1: Generic specification Amendment 1 (1992) Sectional Specification: IEC 60393-6:2003, Potentiometers for use in electronic equipment Part 6: Sectional specif
34、ication: Surface mount preset potentiometers 1.5 Marking The marking of the component and package shall be in accordance with the requirements of 1.4.6 of IEC 60393-6. The details of the marking of the component and package shall be given in full in the Detail Specification. _ 1The preferred values
35、are those of the E-series of IEC 60063 and/or the 1, 2, 5 series. 6 60393-6-1 IEC:2003(E) 1.6 Ordering information Orders for potentiometers covered by this Specification shall contain, in clear or in coded form, the following minimum information: a) rated resistance and tolerance on rated resistanc
36、e; b) resistance law (if other than linear); c) number and issue reference of the Detail Specification and style; d) packaging instructions. 1.7 Certified records of released lots Required/not required. 1.8 Additional information (not for inspection purposes) (The Detail Specification may include in
37、formation such as circuit diagrams, curves, drawings and notes needed for clarification of the Detail Specification). 1.9 Additional or increased severities or requirements to those specified in the Generic and/or Sectional Specification NOTE Additions or increased requirements should be specified o
38、nly when essential.60393-6-1 IEC:2003(E) 7 2 Inspection requirements 2.1 Procedures 2.1.1 For qualification approval, the procedures shall be in accordance with 3.2 of IEC 60393-6. 2.1.2 For quality conformance inspection, the test schedule (Table 2) includes sampling, periodicity, severities and re
39、quirements. The formation of inspection lots is covered by 3.3.1 of IEC 60393-6. For the quality conformance inspection, the values representative of the whole approved range shall be tested within one year (Groups A, B and C only). When drying is called for, Procedure I of 4.3 of IEC 60393-1 shall
40、be used. Table 2 Test schedule for quality conformance inspection: lot-by-lot IL AQL Subclause number and test of IEC 60393-1 (see NOTE 1) D or ND Conditions of test (see NOTE 1) (see NOTE 2) Performance requirements (see NOTE 1) GROUP A INSPECTION (lot-by-lot) Subgroup A1 4.4.1 Visual examination N
41、D II 4,0 % As in 4.4.1 of IEC 60393-1 As specified in 1.5 of this Specification Subgroup A2 4.6 Element resistance ND II 1,0 % As in 4.6.3 of IEC 60393-1 Subgroup A3 4.4.2 Dimensions(gauging) ND S-2 4,0 % As specified in the Detail Specification Subgroup A4 4.7 Terminal resistance 4.5 Continuity 4.1
42、5 Rotational noise ND Resistance between a and b Resistance between b and c Method B: S-3 1,0 % R . R . As in 4.5.2 of IEC 60393-1 . % R or . (whichever is the greater) 4.12 Voltage proof (insulated potentiometers only) Method: Insulation resistance (normal air pressure) As in 4.12.5 100 M GROUP B I
43、NSPECTION (lot-by-lot) Subgroup B1 4.18 Starting torque 4.31 Sealing (if applicable) D Temperature: 85 C to 90 C S-2 1,5 % As specified in the Detail Specification As in 4.31.3 of IEC 60393-1 8 60393-6-1 IEC:2003(E) IL AQL Subclause number and test of IEC 60393-1 (see NOTE 1) D or ND Conditions of t
44、est (see NOTE 1) (see NOTE 2) Performance requirements (see NOTE 1) Subgroup B2 2.1.3.4 of IEC 60393-6 Solderability 4.45 Solvent resistance of the marking (if applicable) ND Aging (if applicable) Solder bath method Temperature: 235 C 5 C Duration: 2 s 0,5 s Solvent: Solvent temperature: . Method 1
45、Rubbing material: cotton wool Recovery: . S-2 1,5 % As in 2.1.3.4 of IEC 60393-6 Legible marking NOTE 1 Subclause numbers of tests and performance requirements refer to IEC 60393-1, except for some severities for environmental tests and limits of change in resistance or output ratio, which have to b
46、e taken from the relevant clauses of IEC 60393-6. NOTE 2 Inspection levels and AQLs are selected from IEC 60410. NOTE 3 In this Table: D = destructive ND = non-destructive IL = inspection level AQL = acceptable quality level See IEC 6041060393-6-1 IEC:2003(E) 9 Table 3 Test schedule for quality conf
47、ormance inspection Sample size & criterion of acceptability (see NOTE 2) Performance requirements (see NOTE 1) Subclause number and test of IEC 60393-1 (see NOTE 1) D or ND Conditions of test (see NOTE 1) pnc GROUP C INSPECTION (periodic) Subgroup C1 4.14 Temperature characteristic of resistance ND
48、Lower category temperature/20 C 20 C/70 C 20 C/Upper category temperature 381 R R . % R R . % R R . % 4.20 End stop torque - For types fitted with end stops: As specified in 4.20.1 of IEC 60393-1 Not less than five times the upper limit of the starting torque (unless otherwise stated by the Detail S
49、pecification) - For types fitted with slipping clutches: As specified in 4.20.2 of IEC 60393-1 As in 4.20.1 of IEC 60393-1 As in 4.20.2 of IEC 60393-1 4.22 Thrust and pull on spindle Only the thrust shall be applied. The pull is not applicable - Half of the specimens: As specified in 4.22.2 of IEC 60393-1 Continuity - Remain
