1、INTERNATIONAL STANDARD IEC 60874-19-2 QC 910005XX0002 First edition 1999-09 Connectors for optical fibres and cables Part 19-2: Fibre optic adaptor (duplex) type SC for single-mode fibre connectors Detail specification Connecteurs pour fibres et cbles optiques Partie 19-2: Adaptateur pour fibres opt
2、iques (duplex) de type SC, pour connecteurs pour fibres optiques monomodales Spcification particulire Reference number IEC 60874-19-2:1999(E)Numbering As from 1 January 1997 all IEC publications are issued with a designation in the 60000 series. Consolidated publications Consolidated versions of som
3、e IEC publications including amendments are available. For example, edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the base publication, the base publication incorporating amendment 1 and the base publication incorporating amendments 1 and 2. Validity of this publication The technical cont
4、ent of IEC publications is kept under constant review by the IEC, thus ensuring that the content reflects current technology. Information relating to the date of the reconfirmation of the publication is available in the IEC catalogue. Information on the subjects under consideration and work in progr
5、ess undertaken by the technical committee which has prepared this publication, as well as the list of publications issued, is to be found at the following IEC sources: IEC web site* Catalogue of IEC publications Published yearly with regular updates (On-line catalogue)* IEC Bulletin Available both a
6、t the IEC web site* and as a printed periodical Terminology, graphical and letter symbols For general terminology, readers are referred to IEC 60050: International Electrotechnical Vocabulary (IEV). For graphical symbols, and letter symbols and signs approved by the IEC for general use, readers are
7、referred to publications IEC 60027: Letter symbols to be used in electrical technology, IEC 60417: Graphical symbols for use on equipment. Index, survey and compilation of the single sheets and IEC 60617: Graphical symbols for diagrams. * See web site address on title page.INTERNATIONAL STANDARD IEC
8、 60874-19-2 QC 910005XX0002 First edition 1999-09 Connectors for optical fibres and cables Part 19-2: Fibre optic adaptor (duplex) type SC for single-mode fibre connectors Detail specification Connecteurs pour fibres et cbles optiques Partie 19-2: Adaptateur pour fibres optiques (duplex) de type SC,
9、 pour connecteurs pour fibres optiques monomodales Spcification particulire PRICE CODE IEC 1999 Copyright - all rights reserved No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in
10、 writing from the publisher. International Electrotechnical Commission 3, rue de Varemb Geneva, Switzerland Telefax: +41 22 919 0300 e-mail: inmailiec.ch IEC web site http:/www.iec.ch J For price, see current catalogueCommission Electrotechnique InternationaleInternational Electrotechnical Commissio
11、n 2 60874-19-2 IEC:1999(E) INTERNATIONAL ELECTROTECHNICAL COMMISSION _ CONNECTORS FOR OPTICAL FIBRES AND CABLES Part 19-2: Fibre optic adaptor (duplex) type SC for single-mode fibre connectors Detail specification FOREWORD 1) The IEC (International Electrotechnical Commission) is a worldwide organiz
12、ation for standardization comprising all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities
13、 the IEC publishes International Standards. Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also par
14、ticipate in this preparation. The IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of the IEC on technical matters express, as nearly as po
15、ssible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested National Committees. 3) The documents produced have the form of recommendations for international use and are published in the form of standards, technical spe
16、cifications, technical reports or guides and they are accepted by the National Committees in that sense. 4) In order to promote international unification, IEC National Committees undertake to apply IEC International Standards transparently to the maximum extent possible in their national and regiona
17、l standards. Any divergence between the IEC Standard and the corresponding national or regional standard shall be clearly indicated in the latter. 5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with
18、one of its standards. 6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60874-19-2 has been prepared by
19、 subcommittee 86B: Fibre optic interconnecting devices and passive components, of IEC technical committee 86: Fibre optics. The text of this standard is based on the following documents: FDIS Report on voting 86B/1221/FDIS 86B/1257/RVD Full information on the voting for the approval of this standard
20、 can be found in the report on voting indicated in the above table. This publication has not been drafted in complete accordance with the ISO/IEC Directives, Part 3. The QC number that appears on the front cover of this publication is the specification number in the IEC Quality Assessment System for
21、 Electronic Components (IECQ). The references to clauses or subclauses of IEC 60874-1 indicated in this part apply to the third edition of IEC 60874-1.60874-19-2 IEC:1999(E) 3 The committee has decided that the contents of this publication will remain unchanged until 2012. At this date, the publicat
22、ion will be reconfirmed; withdrawn; replaced by a revised edition, or amended. A bilingual version of this standard may be issued at a later date. 4 60874-19-2 IEC:1999(E) CONNECTORS FOR OPTICAL FIBRES AND CABLES Part 19-2: Fibre optic adaptor (duplex) type SC for single-mode fibre connectors Detail
23、 specification NATIONAL STANDARDS ORGANIZATION:Date . DETAIL SPECIFICATION IEC QC 910005XX0002 FIBRE OPTIC COMPONENT OF ASSESSED QUALITY IN ACCORDANCE WITH GENERIC SPECIFICATION: QC 910000 (IEC 60874-1) BLANK DETAIL SPECIFICATION: QC 910004 (IEC 60874-1-1) FIBRE OPTIC ADAPTOR CLASSIFICATION: Type: N
24、ame: SC-duplex for single-mode connectors For use in datacom applications as specified in ISO/IEC International Standard 11801: Generic cabling for customer premises Configuration: plug-adaptor-plug Coupling: push-pull Control dimensions: Adaptor: see figures 1, 2 and 3 Gauge: figures 4 and 5 Varian
25、ts: see page 10 Climatic category: 10/60/4 Environmental category: 4 Assessment level: A QUALIFICATION PROCEDURE: Fixed sample procedure SAFETY WARNING: Take care when handling small diameter optical fibre to prevent puncturing the skin, especially in the eye area. Direct viewing of the end of an op
26、tical fibre when it is propagating energy is not recommended unless prior assurance is obtained as to the safe energy output level.60874-19-2 IEC:1999(E) 5 NOTE The dotted lines are for information only and represent the outer shape of the fixture of the adaptor. Figure 1 Adaptor mating face dimensi
27、ons Partial cross section A-A Cross section B-B BC IEC 1025/99 6 60874-19-2 IEC:1999(E) Dimensions Reference Minimum Maximum Notes A B D H I J K L O P R rS T U V AA AB AC AD AE BA BB BC DB DD 4,59 mm 4,90 mm 6,90 mm 0,40 mm 5,51 mm 0,06 mm 1,90 mm 2,00 mm 9,00 mm 7,40 mm 1,00 mm 3,80 mm 5,00 mm 0,60
28、 mm 27 0,80 mm 0,40 mm 0,70 mm 0,40 mm 5,40 mm 10,80 mm 2,70 mm 12,65 mm 5,60 mm 4,79 mm 5,50 mm 7,10 mm 0,80 mm 5,90 mm 1,00 mm 2,10 mm 2,20 mm 9,10 mm 7,50 mm 1,10 mm 4,04 mm 5,30 mm 1,60 mm 33 0,90 mm 0,60 mm 0,80 mm 0,60 mm 5,60 mm 11,20 mm 2,80 mm 12,75 mm 6,99 mm Diameter, 1 Diameter 2 Radius
29、Diameter NOTES 1 The connector alignment feature is a resilient alignment sleeve. The gauge retention force shall be measured with two gauge pins, each inserted to the middle of the alignment feature. The gauge retention force shall be from 2,0 N to 5,9 N for PC and from 2,9 N to 5,9 N for APC. 2 Fo
30、r the angled PC variants No. 1005 and 1006, the two slots “O“ shall be symmetric within 0,03 mm. 3 Where a tolerance of form is not specified, the limits of the dimensions for a feature control the form as well as the size. 4 Where interrelated features of size (features shown with a common axis or
31、centre plane) have no geometric tolerance of location or run-out specified, the limits of the dimensions for a feature control the location tolerance as well as the size. 5 Where perpendicular features (features shown at right angles) have no geometric tolerance of orientation or run-out specified,
32、the limits of the dimensions for a feature control the orientation tolerance as well as the size. Figure 1 Adaptor mating face dimensions (continued)60874-19-2 IEC:1999(E) 7 Dimension mm Reference Minimum Maximum Notes AF AG AH AJ AI AK AL AM AO 34,50 30,20 25,20 2,20 9,20 27,00 2,70 27,50 1,70 35,2
33、0 31,20 25,90 2,40 9,40 27,80 2,80 29,50 2,20 1 1 2 NOTES 1 The dotted lines are illustrative only; the flange may be radiused or have square corners. 2 The maximum thickness of the panel shall be 1,6 mm when the adaptor is mounted using the spring hook. Figure 2 Adaptor dimensions IEC 1026/99 8 608
34、74-19-2 IEC:1999(E) BS BS BQ BP Dimensions mm Reference Minimum Maximum Notes BP BQ BR BS 30,60 26,20 2,40 9,50 31,20 26,40 2,60 10,00 1 NOTE If the adaptor is mounted using bolts only, this hole shall be threaded M2. Figure 3 Panel piercing and mounting detail IEC 1027/9960874-19-2 IEC:1999(E) 9 CN
35、 Cor R CK CL Dimensions mm Reference Minimum Maximum Notes CK CL CN 2,4985 2,80 7,00 2,4995 4,80 1 NOTE Surface roughness grade N4 (0,2 m Ra). Figure 4 Dimension of a pin gauge for an adaptor IEC 1028/99 10 60874-19-2 IEC:1999(E) VARIANT IDENTIFICATION NUMBERS NUMBER: XXXXXXXXXXXXXXX Variant feature
36、 ZZZZ Component name Housing part material Sleeve material Preferred housing colour/indicator 1001 Adaptor SMF Plastic Zirconia Blue 1002 Adaptor SMF Plastic Phosphor bronze Blue 1003 Adaptor SMF Metal Zirconia Blue 1004 Adaptor SMF Metal Phosphor bronze Blue 1005 Adaptor APC Plastic Zirconia Green
37、1006 Adaptor APC Metal Zirconia Green SUPPLEMENTARY INFORMATION Colour: For SMF: blue according to RAL 5015 For APC: green according to RAL 6029 Component marking: The name and/or manufacturers identification mark may be permanently identified. Figure 5 shows an example of the location of component
38、marking. Figure 5 Example of component marking Manufacturers identification mark IEC 1029/9960874-19-2 IEC:1999(E) 11 TABLE 1 FIXED SAMPLE TEST SCHEDULE FOR QUALIFICATION APPROVAL Test sequence Reference IEC 60874-1 (IEC QC 910000) (IEC 61300) n Group 0 Visual examination Dimensions Gauge retention
39、force 4.4.1 (3-1) 4.4.2 (3-1) (3-33) 20 Group 1 Attenuation 4.4.7 (3-4) 20 Group 2 Cold Dry heat Damp heat (steady state) 4.5.17 (2-17) 4.5.18 (2-18) 4.5.19 (2-19) 6 Group 3 Engagement and separation force Mechanical endurance 4.4.5 (3-11) 4.5.32 (2-2) 6 Group 4 Vibration Change of temperature (test
40、 Nb) 4.5.1 (2-1) 4.5.22 (2-22) 4 Group 5 Strength of coupling mechanism 4.5.6 (2-6) 4 NOTES 1 n = sample size (number of adaptors). 2 To satisfy the qualification approval requirements of the detail specification, there shall be no failures of any in the sample groups for any test parameter. If a fa
41、ilure does occur, this shall be investigated and the cause of failure identified and corrected. The test which is affected shall then be repeated using the minimum sample size stated in this detail specification. A fully documented test report and supporting data shall be prepared and made available
42、 for inspection. Failures and the corrective action taken to eliminate failures shall be documented and evidence presented to show that the corrective action will have no detrimental effect on the performance in any of the other tests. Design changes, as opposed to improvements in quality control, w
43、ill necessitate a repeat of the full qualification programme. 3 Unless otherwise indicated, the test details, measurements and performance requirements are given in table 4. 4 Only group 1 tests shall be carried out using a reference connector. All other tests shall be carried out using samples sele
44、cted randomly from production. 12 60874-19-2 IEC:1999(E) TABLE 2 LOT-BY-LOT QUALITY CONFORMANCE INSPECTION SCHEDULE GROUPS A AND B Assessment level A Test sequence Reference IEC 60874-1 (IEC QC 910000) (IEC 61300) IL AQL Group A Visual examination 4.4.1 (3-1) II 4 % Group B Attenuation 4.4.7 (3-4) I
45、I 4 % NOTES 1 Unless otherwise indicated, the details, measurements and performance requirements are given in table 4. 2 IL = Inspection level; AQL = Acceptable quality level. 3 Only attenuation tests shall be carried out using a reference connector. All other tests shall be carried out using produc
46、ts selected randomly from production.60874-19-2 IEC:1999(E) 13 TABLE 3 PERIODIC QUALITY CONFORMANCE INSPECTION SCHEDULE GROUPS C AND D Assessment level A Test sequence Reference IEC 60874-1 (IEC QC 910000) (IEC 61300) np Group C0 Visual examination Dimensions Gauge retention force 4.4.1 (3-1) 4.4.2
47、3-1) (3-33) 18 24 Group C1 Attenuation 4.4.7 (3-4) 18 24 Group C2 Cold Dry heat Damp heat (steady state) 4.5.17 (2-17) 4.5.18 (2-18) 4.5.19 (2-19) 62 4 Group D0 Visual examination Dimensions Gauge retention force 4.4.1 (3-1) 4.4.2 (3-1) (3-33) 20 48 Group D1 Attenuation 4.4.7 (3-4) 20 48 Group D2 C
48、old Dry heat Damp heat (steady state) 4.5.17 (2-17) 4.5.18 (2-18) 4.5.19 (2-19) 64 8 Group D3 Engagement and separation force Mechanical endurance 4.4.5 (3-11) 4.5.2 (2-2) 6 48 Group D4 Vibration Change of temperature (test Nb) 4.5.1 (2-1) 4.5.22 (2-22) 44 8 Group D5 Strength of coupling mechanism 4
49、5.6 (2-6) 4 48 NOTES 1 n = sample size (number of plugs); p = periodicity in months. 2 To satisfy the conformance inspection requirements of the detail specification, there shall be no failures in the sample groups for any test parameter. If a failure does occur, this shall be investigated and the cause of failure identified and corrected. The test which is a
