1、 IEC 62841-2-11 Edition 1.0 2015-11 INTERNATIONAL STANDARD NORME INTERNATIONALE Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery Safety Part 2-11: Particular requirements for hand-held reciprocating saws Outils lectroportatifs moteur, outils portables et mac
2、hines pour jardins et pelouses Scurit Partie 2-11: Exigences particulires pour les scies alternatives portatives IEC 62841-2-11:2015-11(en-fr) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2015 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication
3、may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry
4、 about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque fo
5、rme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de lIEC ou du Comit national de lIEC du pays du demandeur. Si vous avez des questions sur le copyright de lIEC ou si vous dsirez obtenir des droits supplmentaires sur cette publi
6、cation, utilisez les coordonnes ci-aprs ou contactez le Comit national de lIEC de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (
7、IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest ed
8、ition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC
9、, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Publis
10、hed - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containi
11、ng more than 30 000 terms and definitions in English and French, with equivalent terms in 15 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary More than 60 000 electrotechnical terminology entries in English and French
12、extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further
13、 assistance, please contact the Customer Service Centre: csciec.ch. A propos de lIEC La Commission Electrotechnique Internationale (IEC) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparent
14、es. A propos des publications IEC Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue IEC - webstore.iec.ch/catalogue Application autonome pour consulter tous les ren
15、seignements bibliographiques sur les Normes internationales, Spcifications techniques, Rapports techniques et autres documents de lIEC. Disponible pour PC, Mac OS, tablettes Android et iPad. Recherche de publications IEC - www.iec.ch/searchpub La recherche avance permet de trouver des publications I
16、EC en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. IEC Just Published - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications IEC. Just Published dtaille les nouv
17、elles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents da
18、ns 15 langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (IEV) en ligne. Glossaire IEC - std.iec.ch/glossary Plus de 60 000 entres terminologiques lectrotechniques, en anglais et en franais, extraites des articles Termes et Dfinitions des publications IEC parues depui
19、s 2002. Plus certaines entres antrieures extraites des publications des CE 37, 77, 86 et CISPR de lIEC. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 62841-2-11 Edition 1.0 2015-11
20、INTERNATIONAL STANDARD NORME INTERNATIONALE Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery Safety Part 2-11: Particular requirements for hand-held reciprocating saws Outils lectroportatifs moteur, outils portables et machines pour jardins et pelouses Scuri
21、t Partie 2-11: Exigences particulires pour les scies alternatives portatives INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE ICS 25.140.20, 25.140.30 ISBN 978-2-8322-2998-9 Registered trademark of the International Electrotechnical Commission Marque dpose de la C
22、ommission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 IEC 62841-2-11:2015 IEC 2015 CONTENTS FOREWORD . 4 1 Scope 6 2 Normative
23、references 6 3 Terms and definitions 6 4 General requirements 6 5 General conditions for the tests . 7 6 Radiation, toxicity and similar hazards . 7 7 Classification . 7 8 Marking and instructions 7 9 Protection against access to live parts . 7 10 Starting . 7 11 Input and current . 8 12 Heating 8 1
24、3 Resistance to heat and fire 8 14 Moisture resistance . 8 15 Resistance to rusting . 8 16 Overload protection of transformers and associated circuits 8 17 Endurance . 8 18 Abnormal operation . 8 19 Mechanical hazards . 8 20 Mechanical strength 9 21 Construction 9 22 Internal wiring 9 23 Components
25、10 24 Supply connection and external flexible cords . 10 25 Terminals for external conductors 10 26 Provision for earthing 10 27 Screws and connections 10 28 Creepage distances, clearances and distances through insulation . 10 Annexes . 13 Annex I (informative) Measurement of noise and vibration emi
26、ssions . 13 Annex K (normative) Battery tools and battery packs . 20 Annex L (normative) Battery tools and battery packs provided with mains connection or non-isolated sources . 21 Bibliography 22 Figure 101 Test probe 11 Figure 102 Typical designs of jig saws . 12 Figure 103 Typical designs of sabr
27、e saws 12 Figure I.101 Test set-up for jig saws 17 Figure I.102 Test set-up for sabre saws . 18 IEC 62841-2-11:2015 IEC 2015 3 Figure I.103 Positions of transducers for sabre saws . 19 Figure I.104 Positions of transducers for jig saws 19 Table 4 Required performance levels . 8 Table I.101 Test cond
28、itions for sabre and jig saws cutting board 14 Table I.102 Test conditions for jig saws cutting sheet metal . 15 Table I.103 Test conditions for sabre saws cutting wooden beams . 15 4 IEC 62841-2-11:2015 IEC 2015 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TR
29、ANSPORTABLE TOOLS AND LAWN AND GARDEN MACHINERY SAFETY Part 2-11: Particular requirements for hand-held reciprocating saws FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National
30、 Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly
31、Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- government
32、al organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on tec
33、hnical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by
34、IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international unif
35、ormity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5)
36、 IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensu
37、re that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of a
38、ny nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the ref
39、erenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. Inte
40、rnational Standard IEC 62841-2-11 has been prepared by IEC technical committee 116: Safety of motor-operated electric tools. The text of this standard is based on the following documents: FDIS Report on voting 116/246/FDIS 116/256/RVD Full information on the voting for the approval of this standard
41、can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. IEC 62841-2-11:2015 IEC 2015 5 This Part 2-11 is to be used in conjunction with the first edition of IEC 62841-1 (2014). This Part 2-11 supplements
42、or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC standard: Particular requirements for hand-held reciprocating saws. Where a particular subclause of Part 1 is not mentioned in this Part 2-11, that subclause applies as far as relevant. Where this standard states
43、“addition”, “modification” or “replacement”, the relevant text in Part 1 is to be adapted accordingly. The following print types are used: requirements: in roman type; test specifications: in italic type; notes: in small roman type. The terms defined in Clause 3 are printed in bold typeface. Subclau
44、ses, notes and figures which are additional to those in Part 1 are numbered starting from 101. A list of all parts of the IEC 62841 series, under the general title: Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery Safety, can be found on the IEC website. The
45、 committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised
46、edition, or amended. NOTE The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requiremen
47、ts and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. 6 IEC 62841-2-11:2015 IEC 2015 ELECTRIC MOTOR-OPERATED HAND
48、-HELD TOOLS, TRANSPORTABLE TOOLS AND LAWN AND GARDEN MACHINERY SAFETY Part 2-11: Particular requirements for hand-held reciprocating saws 1 Scope This clause of Part 1 is applicable, except as follows: Addition: This part of IEC 62841 applies to reciprocating saws such as jig saws and sabre saws. 2
49、Normative references This clause of Part 1 is applicable, except as follows: Addition: ISO 16893-1:2008, Wood based panels Particleboard Part 1: Classifications 3 Terms and definitions This clause of Part 1 is applicable, except as follows: Additional definitions: 3.101 reciprocating saw tool intended for cutting various materials with a blade or blades acting in a reciprocating or oscil
