1、IEEE Standard for Relaxor-Based Single Crystals for Transducer and Actuator Applications IEEE Std 1859-2017 IEEE Ultrasonics, Ferroelectronics and Frequency Control Society Sponsored by the Standards Committee IEEE 3 Park Avenue New York, NY 10016-5997 USAIEEE Std 1859-2017 IEEE Standard for Relaxor
2、-Based Single Crystals for Transducer and Actuator Applications Sponsor Standards Committee of the IEEE Ultrasonics, Ferroelectronics and Frequency Control Society Approved 18 May 2017 IEEE-SA Standards BoardAbstract: The physical and electromechanical requirements for relaxor-based piezoelectric si
3、ngle crystals of lead magnesium niobatelead titanate (PMN-PT) and lead zinc niobatelead titanate (PZN-PT) solid solutions of perovskite structure, with poling along the crystallographic c-axis (i.e., the 001-direction), that are intended for fabrication into single plates, multilayer plate devices,
4、and composites with other passive materials for use in medical, industrial, and military transducers, actuators, and sensors are covered in this standard. Definitions of terms and recommended practices for measuring the physical and electromechanical properties of these materials are also included i
5、n this standard. Keywords: actuators and sensors, crystal compositions, crystal properties and measurements, crystal property specifications, electromechanical transducers, IEEE 1859, lead magnesium niobatelead titanate solid solution, lead zinc niobatelead titanate solid solution, piezoelectric sin
6、gle crystals, PMN-PT, PZN-PT The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2017 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 22 December 2017. Printed in the United States of America.
7、 IEEE is a registered trademark in the U.S. Patent fitness for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEEE standards document
8、s are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE standard. Further
9、more, the viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting or rendering professi
10、onal or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of reasonable care in an
11、y given circumstances or, as appropriate, seek the advice of a competent professional in determining the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCU
12、REMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY S
13、TANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE W AS FORESEEABLE.4 Copyright 2017 IEEE. All rights reserved. Translations The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE standard is tr
14、anslated, only the English version published by IEEE should be considered the approved IEEE standard. Official statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inferred to be the official positi
15、on of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall make it clear that his or her views should be considered the p
16、ersonal views of that individual rather than the formal position of IEEE. Comments on standards Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not provide consulting information or advice per
17、taining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important that any responses to comments and questions
18、 also receive the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Committees are not able to provide an instant response to comments or questions except in those cases where the matter has previously been addressed. For the sam
19、e reason, IEEE does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes La
20、ne Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the standard are r
21、esponsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights IEEE draft and approved standard
22、s are copyrighted by IEEE under U.S. and international copyright laws. They are made available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promo
23、tion of engineering practices and methods. By making these documents available for use and adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents.5 Copyright 2017 IEEE. All rights reserved. Photocopies Subject to payment of the appropriate fee,
24、 IEEE will grant users a limited, non-exclusive license to photocopy portions of any individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosew
25、ood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Updating of IEEE Standards documents Users of IEEE Standards documents should be aware that these
26、documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigen
27、da, or errata then in effect. Every IEEE standard is subjected to review at least every ten years. When a document is more than ten years old and has not undergone a revision process, it is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present stat
28、e of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE Xplore at ht
29、tp:/ ieeexplore .ieee .or g/ or contact IEEE at the address listed previously. For more information about the IEEE-SA or IEEEs standards development process, visit the IEEE-SA Website at http:/ standards .ieee .or g. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Websit
30、e at the following URL: http:/ standards .ieee .org/ findstds/ errata/ index .html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publi
31、cation of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE- S
32、A Website at http:/ standards .ieee .or g/ about/ sasb/ patcom/ patents .html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstra
33、bly free of any unfair discrimination to applicants desiring to obtain such licenses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inqui
34、ries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised
35、 that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association.6 Copyright 2017 IEEE. All rights reserved. Participants At the time this standard was
36、submitted to the IEEE-SA Standards Board for approval, the P1859 Relaxor-Based Single Crystals for Transducer and Actuator Applications Working Group had the following membership: Zuo-Guang Y e, Chair Lynn Ewart, Vice Chair Jun Luo, Technical Editor Jian Tian, Technical Editor Ahmed Amin David Baird
37、 Stuart Blacker Alex Butler Wenwu Cao Sandy Cochran Christine E. M. Demore Peter Finkel Pengdi Han Ho-Yong Lee Leong Chew Lim Christopher Lynch James Powers Harold Robinson Scott Smith Glenn Whitworth Carl Wu Shujun Zhang Early versions of this standard benefited from the leadership of Seung-Eek (Ea
38、gle) Park and Sorah Rhee and the initiative and valued input of Y ohachi (John) Y amashita. The following members of the individual balloting committee voted on this standard. Balloters may have voted for approval, disapproval, or abstention. Markys Cain Sandy Cochran Matthew Deangelis Christine E.
39、M. Demore Lynn Ewart Vincent Fratello Randall Groves Wesley Hackenberger Werner Hoelzl Sang Goo Lee Jian-Y u Lu Jun Luo Dean Mchenry Richard Meyer Michael Newman Ming-Jen Pan Harold Robinson Lowell Smith Jian Tian Zuo-Guang Y e Shujun Zhang Michael Zipparo When the IEEE-SA Standards Board approved s
40、tandard on 18 May 2017, it had the following membership: Jean-Philippe Faure, Chair Gary Hoffman, Vice Chair John D. Kulick, Past Chair Konstantinos Karachalios, Secretary Chuck Adams Masayuki Ariyoshi Ted Burse Stephen Dukes Doug Edwards J. Travis Griffith Michael Janezic Thomas Koshy Joseph L. Koepfinger* Kevin Lu Daleep Mohla Damir Novosel Ronald C. Petersen Annette D. Reilly Robby Robson Dorothy Stanley Adrian Stephens Mehmet Ulema Phil Wennblom Howard Wolfman Y u Y uan *Member Emeritus
