1、IEEE Guide for Thermal Resistivity Measurements of Soils and Backfill Materials IEEE Std 442-2017 (Revision of IEEE Std 442-1981) IEEE Power and Energy Society Sponsored by the Insulated Conductors Committee IEEE 3 Park Avenue New York, NY 10016-5997 USAIEEE Std 442-2017 (Revision of IEEE Std 442-19
2、81) IEEE Guide for Thermal Resistivity Measurements of Soils and Backfill Materials Sponsor Insulated Conductors Committee of the IEEE Power and Energy Society Approved 28 September 2017 IEEE-SA Standards BoardAbstract: The measurement of thermal resistivity of soil and backfill materials to include
3、 concrete, engineered backfills, grout, rock, sand, and any other material used to encase the cable system installed in the ground is covered in this guide. A thorough knowledge of the thermal properties of a soil or backfill material enables the user to properly design, rate, and load underground c
4、ables. The method used is based on the theory that the rate of temperature rise of a line heat source is dependent upon the thermal constants of the medium in which it is placed. The designs for both laboratory and field thermal probes are also described in this guide. Keywords: backfill, IEEE 442,
5、soil, soil thermal properties, thermal needle, thermal probe, thermal property analyzer, thermal resistivity The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2018 by The Institute of Electrical and Electronics Engineers, Inc. All right
6、s reserved. Published 7 May 2018. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent fitness for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all condit
7、ions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide o
8、ther goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard. In publishing and ma
9、king its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon hi
10、s or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competent professional in determining the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
11、 EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
12、 ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE W AS FORESEEABLE.4 Copyright 2018 IEEE. All rights reserved. Translations The IEEE consensus development process involves the rev
13、iew of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the approved IEEE standard. Official statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Opera
14、tions Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE stan
15、dards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position of IEEE. Comments on standards Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with
16、 IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concern
17、ed interests, it is important that any responses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Committees are not able to provide an instant response to comments or questions except
18、in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on standards should be submitte
19、d to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to
20、any applicable regulatory requirements. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may
21、 not be construed as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws. They are made available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regul
22、ations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making these documents available for use and adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents.5 Copyright 2018 IEEE. A
23、ll rights reserved. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of any individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of licensing fe
24、es, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Updating of IEEE Standar
25、ds documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. A current IEEE document at any point in time consists of th
26、e current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at least every ten years. When a document is more than ten years old and has not undergone a revision process, it is reasonable to conclude that its conten
27、ts, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended through the is
28、suance of amendments, corrigenda, or errata, visit the IEEE Xplore at http:/ ieeexplore .ieee .or g/ or contact IEEE at the address listed previously. For more information about the IEEE-SA or IEEEs standards development process, visit the IEEE-SA Website at http:/ standards .ieee .or g. Errata Erra
29、ta, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/ standards .ieee .org/ findstds/ errata/ index .html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this stand
30、ard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an A
31、ccepted Letter of Assurance, then the statement is listed on the IEEE- SA Website at http:/ standards .ieee .or g/ about/ sasb/ patcom/ patents .html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under r
32、easonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential
33、 Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reason
34、able or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association.6 Copyright 201
35、8 IEEE. All rights reserved. Participants At the time this guide was submitted to the IEEE-SASB for approval, the IEEE P442 Working Group had the following membership: Nimesh Patel, Chair Sudhakar Cherukupalli, Vice Chair Earle C. (Rusty) Bascom III William Black Chris Grodzinski Dennis E. Johnson R
36、achel Mosier Lucian Munteanu Deepak Parmar David Purnhagen Walter Zenger The following members of the individual balloting committee voted on this guide. Balloters may have voted for approval, disapproval, or abstention. Saleman Alibhay Thomas Barnes Earle C. (Rusty) Bascom III William Black William
37、 Bloethe Kenneth Bow Kent Brown William Byrd Sudhakar Cherukupalli Michael Chirico Robert Christman Gary Donner Donald Dunn Todd Goyette Randall Groves Ajit Gwal Jeffrey Helzer Lee Herron Lauri Hiivala Werner Hoelzl Magdi Ishac Dennis E. Johnson Jim Kulchisky Chung-Yiu Lam Michael Lauxman John Meran
38、do Daleep Mohla Rachel Mosier Jerry Murphy Arthur Neubauer Michael Newman Charles Ngethe Lorraine Padden Deepak Parmar Nimesh Patel Shashikant Patel Branimir Petosic Christopher Petrola Thomas Proios Charles Rogers Ryandi Ryandi Daniel Sabin Bartien Sayogo Michael Smalley Jeremy Smith Jerry Smith Da
39、vid Tepen Peter Tirinzoni Nijam Uddin John V ergis Kenneth White Jian Y u Walter Zenger Tiebin Zhao When the IEEE-SA Standards Board approved this guide on 28 September 2017, it had the following membership: Jean-Phillipe Faure, Chair Gary Hoffman, Vice Chair John D. Kulick, Past Chair Konstantinos
40、Karachalios, Secretary Chuck Adams Masayuki Ariyoshi Ted Burse Stephen Dukes Doug Edwards J. Travis Griffith Michael Janezic Thomas Koshy Joseph L. Koepfinger* Kevin Lu Daleep Mohla Damir Novosel Ronald C. Petersen Annette D. Reilly Robby Robson Dorothy Stanley Adrian Stephens Mehmet Ulema Phil Wenn
41、blom Howard Wolfman Y u Y uan *Member Emeritus7 Copyright 2018 IEEE. All rights reserved. Introduction This introduction is not part of IEEE Std 442-2017, IEEE Guide for Thermal Resistivity Measurements of Soils and Backfill Materials. An important design consideration in the design of underground c
42、able systems is to understand the thermal resistivity characteristics of the materials that surround the cable. Over the years, many utilities, consultants, and testing firms have measured soil thermal resistivity both in situ and in the laboratory on selected soil samples. Such measurements have ut
43、ilized various types of equipment and measurement techniques. In many cases, these testing methods have yielded inaccurate or inconsistent measurements of soil thermal resistivity. The Insulated Conductors Committee, recognizing the need for industry guidelines for the measurement of soil thermal re
44、sistivity, has prepared this guide to provide the user information on the test equipment that should be used to perform these material resistivity measurements. In addition, the guide provides information on how to make the in-situ or laboratory resistivity measurements and interpret the data in ord
45、er to provide meaningful results using this equipment. The in-situ resistivity of a soil changes from season to season, due to changes in the moisture content of the soil or due to the relocation of the water table. It is important to consider these factors when determining a soil thermal resistivity value for ampacity calculations and rating underground cables.
