1、 American National Standard Guide for Electrostatic Discharge Test Methodologies and Acceptance Criteria for Electronic Equipment Accredited by the American National Standards Institute IEEE 3 Park Avenue New York, NY 10016-5997 USA Accredited Standards Committee C63Electromagnetic Compatibility ANS
2、I C63.16-2016(Revision ofANSI C63.16-1993) C63ANSI C63.16-2016 (Revision of ANSI C63.16-1993) American National Standard Guide for Electrostatic Discharge Test Methodologies and Acceptance Criteria for Electronic Equipment Accredited Standards Committee C63Electromagnetic Compatibility accredited by
3、 the American National Standards Institute Secretariat Institute of Electrical and Electronics Engineers, Inc Approved 1 February 2016 American National Standards Institute Copyrights and permissions ANSI C63 and the IEEE thank the International Electrotechnical Commission (IEC) for permission to re
4、produce Information (Figure 1, Figure 2, Figure 3, Figure 4, and Figure 6 of this standard) from its International Standard IEC 61000-4-2 ed. 2.0 (2008). All such extracts are copyright of IEC, Geneva, Switzerland. All rights reserved. Further information on the IEC is available from www.iec.ch. IEC
5、 has no responsibility for the placement and context in which the extracts and contents are reproduced by the author, nor is IEC in any way responsible for the other content or accuracy therein. Abstract: Expanded explanations, best practices, and guidance for avoiding the pitfalls associated with e
6、lectrostatic discharge (ESD) testing to IEC and other international ESD standards are provided and should be considered a supplement to these standards, rather than a replacement. Unique ESD test procedures related to connecting charged peripherals to equipment in use are also included. Keywords: ai
7、r discharge, ANSI C63.16, contact discharge, coupling plane, direct discharge, electrostatic discharge (ESD), ESD event, ESD immunity, ESD simulator, ESD test criteria, indirect discharge The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyrigh
8、t 2016 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 6 May 2016. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent (978) 750-8400. Permission to photocopy portions of any individual standard for educational clas
9、sroom use can also be obtained through the Copyright Clearance Center. Errata Users are encouraged to check the IEEE Errata URL (http:/standards.ieee.org/findstds/errata/index.html), and the one for ASC C63at http:/www.c63.org/explanations_interpretations_request.htm, for errata periodically. Interp
10、retations (ASC C63standards) Current interpretations are essential to the understanding of all ASC C63standards. To assist in the meanings of requirements, informative interpretations are available at the following URL: http:/www.c63.org/documents/misc/posting/new_interpretations.htm. Users are caut
11、ioned that, although interpretations do not and cannot change the requirements of a standard, they serve to clarify the meanings of requirements. All interpretations are informative rather than normative, until such time as the standard is revised (consistent with ASC C63ANSI-accredited operating pr
12、ocedures) to incorporate the interpretation as a normative requirement. Important Notices and Disclaimers Concerning IEEE Standards Documents IEEE documents are made available for use subject to important notices and legal disclaimers. These notices and disclaimers, or a reference to this page, appe
13、ar in all standards and may be found under the heading “Important Notice” or “Important Notices and Disclaimers Concerning IEEE Standards Documents.” Notice and Disclaimer of Liability Concerning the Use of IEEE Standards Documents IEEE Standards documents (standards, recommended practices, and guid
14、es), both full-use and trial-use, are developed within IEEE Societies and the Standards Coordinating Committees of the IEEE Standards Association (“IEEE-SA”) Standards Board. IEEE (“the Institute”) develops its standards through a consensus development process, approved by the American National Stan
15、dards Institute (“ANSI”), which brings together volunteers representing varied viewpoints and interests to achieve the final product. Volunteers are not necessarily members of the Institute and participate without compensation from IEEE. While IEEE administers the process and establishes rules to pr
16、omote fairness in the consensus development process, IEEE does not independently evaluate, test, or verify the accuracy of any of the information or the soundness of any judgments contained in its standards. IEEE does not warrant or represent the accuracy or content of the material contained in its
17、standards, and expressly disclaims all warranties (express, implied and statutory) not included in this or any other document relating to the standard, including, but not limited to, the warranties of: merchantability; fitness for a particular purpose; non-infringement; and quality, accuracy, effect
18、iveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does no
19、t imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developments
20、in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any other pers
21、on or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competent professional in determining the appropriateness of a given
22、IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
23、 LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE. Translations The I
24、EEE consensus development process involves the review of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the approved IEEE standard. Official statements A statement, written or oral, that is not processed in
25、 accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses,
26、 an individual presenting information on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position of IEEE. Comments on standards Comments for revision of IEEE Standards documents are welcome from any intereste
27、d party, regardless of membership affiliation with IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Sin
28、ce IEEE standards represent a consensus of concerned interests, it is important that any responses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Committees are not able to provide an
29、 instant response to comments or questions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE worki
30、ng group. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any IEE
31、E Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compli
32、ance with applicable laws, and these documents may not be construed as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws. They are made available by IEEE and are adopted for a wide variety of both public and private uses. These
33、 include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making these documents available for use and adoption by public authorities and private users, IEEE does not waive any rights in c
34、opyright to the documents. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of any individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of licen
35、sing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Updating of IEEE
36、Standards documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time consi
37、sts of the current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at least every ten years. When a document is more than ten years old and has not undergone a revision process, it is reasonable to conclude that i
38、ts contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended throu
39、gh the issuance of amendments, corrigenda, or errata, visit the IEEE-SA Website at http:/ieeexplore.ieee.org/xpl/standards.jsp or contact IEEE at the address listed previously. For more information about the IEEE SA or IEEEs standards development process, visit the IEEE-SA Website at http:/standards
40、ieee.org. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection th
41、erewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Submitter is willing o
42、r unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Essential Patent Claims may exist for which a Letter of Assur
43、ance has not been received. The IEEE is not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submi
44、ssion of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Furthe
45、r information may be obtained from the IEEE Standards Association. Copyright 2016 IEEE. All rights reserved. vii Participants At the time this guide was published, Accredited Standards Committee C63Electromagnetic Compatibility had the following membership: Daniel Hoolihan, Chair Dan Sigouin, Vice C
46、hair Jerry D. Ramie, Secretary Sue Vogel, Secretariat Organization Represented Name of Representative AlcatelLucent Dheena Moongilan American Council of Independent Laboratories (ACIL) . Harry H. Hodes . John Repella (Alt.) American Radio Relay League (ARRL) Edward F. Hare . Kermit Carlson (Alt.) Ap
47、ple, Inc. Manjit Walia Indrandil Sen (Alt.) Blackberry Corporation . Masud Attayi Daoud Attayi (Alt.) Bureau Veritas . Jonathan Stewart Cisco Systems . Andy Griffin Dave Case (Alt.) Dell Inc. . Richard Worley Ericsson AB Vladimir Bazhanov . Kenth Skoglund (Alt.) ETS-Lindgren Zhong Chen Michael Foege
48、lle (Alt.) Federal Communications Commission (FCC) William Hurst . Steve Jones (Alt.) Food and Drug Administration (FDA) Jeffrey L. Silberberg Donald M. Witters (Alt.) Industry Canada . Jason Nixon . Horia Popovici (Alt.) Information Technology Industry Council (ITIC) John Hirvela . Joshua Rosenberg
49、 (Alt.) IEEE-Electromagnetic Compatibility Society (EMCS) . John Norgard Henry Benitez (Alt.) Liberty Labs Mike Howard Brandt Langer (Alt.) Motorola Mobility Tom Knipple Motorola Solutions Deanna Zakharia National Institute of Standards and Technology (NIST) . William Young Jason Coder (Alt.) Northwest EMC Dean Ghizzone . Greg Kiemel (Alt.) PCTEST Engineering Laboratory Greg Snyder Dennis Ward (Alt.) Qualcomm Technologies, Inc. John Forrester Mark Klerer (Alt.) Society of Automotive Engineers (SAE) Rick Lombardi Poul Andersen (Alt.) Telecommunication Certification Body
