1、 Reference numberISO 10911:2010(E)ISO 2010INTERNATIONAL STANDARD ISO10911Second edition2010-03-01Solid hardmetal end mills with cylindrical shank Dimensions Fraises cylindriques deux tailles monobloc en mtaux-durs Dimensions ISO 10911:2010(E) PDF disclaimer This PDF file may contain embedded typefac
2、es. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringi
3、ng Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimiz
4、ed for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unle
5、ss otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO c
6、opyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2010 All rights reservedISO 10911:2010(E) ISO 2010 All rights reserved iiiForeword ISO (the International Organization for Standardiz
7、ation) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be
8、 represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standar
9、ds are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Intern
10、ational Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10911 wa
11、s prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 9, Tools with cutting edges made of hard cutting materials. This second edition cancels and replaces the first edition (ISO 10911:1994) which has been technically revised. INTERNATIONAL STANDARD ISO 10911:2010(E) ISO 2010 All
12、rights reserved 1Solid hardmetal end mills with cylindrical shank Dimensions 1 Scope This International Standard specifies the dimensions of solid hardmetal end mills with cylindrical shank. 2 Normative references The following referenced documents are indispensable for the application of this docum
13、ent. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3338-1, Cylindrical shanks for milling cutters Part 1: Dimensional characteristics of plain cylindrical shanks ISO 3338-2, Cylindri
14、cal shanks for milling cutters Part 2: Dimensional characteristics of flatted cylindrical shanks 3 Dimensions The dimensions of solid hardmetal end mills with plain cylindrical shank are specified in Figure 1 and Table 1. NOTE The dimensions given in Table 1 also apply to solid hardmetal end mills w
15、ith flatted cylindrical shanks in accordance with ISO 3338-2. 4 Centre cutting End mills with two flutes shall be centre-cutting (slot drills). End mills with three flutes or more may be centre-cutting. Key 1 Plain cylindrical shank in accordance with ISO 3338-1 NOTE See Table 1 for dimensions. Figu
16、re 1 Example of an end mill ISO 10911:2010(E) 2 ISO 2010 All rights reservedTable 1 Dimensions of end mills with two flutes Dimensions in millimetres Short cutting part Long cutting part Cutting diameter ShankdiameteraOverall length Cutting length Overall length Cutting length d1d2l1bl2cl1dl2h10 h6
17、2 or 3 cutting edges 4 cutting edges 2 or 3 cutting edges 4 cutting edges 1,0 3,0 38,0 3,0 3,0 1,5 3,0 38,0 3,0 4,0 3,0 38,0 3,0 4,0 38,0 6,0 7,0 2,0 6,0 50,0 3,0 4,0 57,0 6,0 7,0 3,0 38,0 3,0 4,0 38,0 7,0 8,0 2,5 6,0 50,0 3,0 4,0 57,0 7,0 8,0 3,0 38,0 4,0 5,0 38,0 7,0 8,0 3,0 6,0 50,0 4,0 5,0 57,0
18、7,0 8,0 3,5 6,0 50,0 4,0 6,0 57,0 7,0 10,0 4,0 6,0 54,0 5,0 8,0 57,0 8,0 11,0 4,5 6,0 54,0 5,0 8,0 57,0 8,0 11,0 5,0 6,0 54,0 6,0 9,0 57,0 10,0 13,0 6,0 6,0 54,0 7,0 10,0 57,0 10,0 13,0 7,0 8,0 58,0 8,0 11,0 63,0 13,0 16,0 8,0 8,0 58,0 9,0 12,0 63,0 16,0 19,0 9,0 10,0 66,0 10,0 13,0 72,0 16,0 19,0 1
19、0,0 10,0 66,0 11,0 14,0 72,0 19,0 22,0 12,0 12,0 73,0 12,0 16,0 83,0 22,0 26,0 14,0 14,0 75,0 14,0 18,0 83,0 22,0 26,0 16,0 16,0 82,0 16,0 22,0 92,0 26,0 32,0 18,0 18,0 84,0 18,0 24,0 92,0 26,0 32,0 20,0 20,0 92,0 20,0 26,0 104,0 32,0 38,0 aFor the dimensions, see ISO 3338-1. bTolerance on l1, short cutting part: 2,00mm.+cTolerances on l2: for l2up to 10 mm: 1, 00mm;+for l2 10 mm u 22 mm: 1, 50mm;+for l2 22 mm: 2,00mm.+dTolerance on l1, long cutting part: 2,00mm.+ISO 10911:2010(E) ICS 25.100.20 Price based on 2 pages ISO 2010 All rights reserved
