1、INTERNATIONAL STANDARD IS0 10945 First edition 1994-l l-l 5 Hydraulic fluid power - Gas-loaded accumulators - Dimensions of gas ports Transmissions hydrauliques - Accumulateurs hydropneumatiques - Dimensions des orifices gaz Reference number IS0 10945:1994(E) Copyright International Organization for
2、 Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IS0 10945:1994(E) Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). Th
3、e work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-gov
4、ernmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for
5、voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard IS0 10945 was prepared by Technical Committee lSO/TC 131, Nuid power systems. 0 IS0 1994 All rights reserved. Unless otherwise specified, no part of this pu
6、blication may be reproduced or utilized in any form or by any means, electronrc or mechanical. including photocopying and microfilm, without permission in writing from the publisher. International Organization for Standardization Case Postale 56 l CH-1211 Geneve 20 l Switzerland Printed in Switzerla
7、nd ii Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-INTERNATIONAL STANDARD Q IS0 IS0 10945:1994(E) Hydraulic fluid power - Gas-loaded accumulators - Dimensions of gas p
8、orts 1 Scope This International Standard specifies the types and the dimensions of the gas filling ports of gas-loaded ac- cumulators used in hydraulic fluid power systems. It describes two male ports for filling the gas side of a gas-loaded accumulator. These ports are designated by the following:
9、 male port with Ml 6 x 2 thread, in accordance with IS0 261 and IS0 724, which is preferred for new designs (see 4.1); - male port with 8Vl thread in accordance with IS0 4570-I (see 4.2). IS0 724:1993, IS0 general-purpose metric screw threads - Basic dimensions. IS0 4570-1:1977, Tyre valve threads
10、 Part I: Threads WI, 5V2, 6V7 and 8Vl. IS0 5598:1985, Fluid power systems and compo- nents - Vocabulary. 3 Definitions For the purposes of this International Standard, the definitions given in IS0 5598 apply. 4 Dimensions 4.1 For a male port with Ml6 x 2 threads, the di- mensions shall conform to t
11、hose shown in figure 1. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publi- cation, the editions indicated were valid. All standards are subject to revision, and parties t
12、o agreements based on this International Standard are encouraged to investigate the possibility of applying the most re- cent editions of the standards indicated below. Members of IEC and IS0 maintain registers of cur- rently valid International Standards. IS0 261:-l, /SO genera/-purpose metric scre
13、w threads - General plan. 4.2 For a male port with 8Vl thread the dimensions shall conform to those shown in figure2. 5 Identification statement (Reference to this International Standard) It is recommended to manufacturers to use the fol- lowing statement in test reports, catalogues and sales litera
14、ture when electing to comply with this Inter- national Standard: “Gas ports for gas-loaded accumulators conforming to IS0 10945:1994, Hydraulic fluid power - Gas- loaded accumulators - Dimensions of gas ports .I 1) To be published. (Revision of IS0 261 :1973) 1 Copyright International Organization f
15、or Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IS0 10945:1994(E) Q IS0 Dimensions in millimetres, surface roughness in micrometres I) In accordance with IS0 261 and IS0 724. Figure 1 - Dimensions for male po
16、rt with Ml6 x 2 threads (to be used for new designs) Dimensions in millimetres, surface roughness in micrometres I) In accordance with IS0 4570-I. Figure 2 - Dimensions for male port 8Vl Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo r
17、eproduction or networking permitted without license from IHS-,-,-IS0 10945:1994(E) Q IS0 ICS 23.100.30 Descriptors: hydraulic fluid power, hydraulic equipment, hydropneumattc accumulators, ports (openings), onfrces, dimensions Price based on 2 pages Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
