1、 ISO 2012 Road vehicles Compressed natural gas (CNG) fuel system components Part 18: Filter Vhicules routiers Composants des systmes de combustible gaz naturel comprim (GNC) Partie 18: Filtre INTERNATIONAL STANDARD ISO 15500-18 Second edition 2012-04-15 Reference number ISO 15500-18:2012(E) ISO 1550
2、0-18:2012(E) ii ISO 2012 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2012 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permissio
3、n in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ISO 15500-18:2012(E) Foreword IS
4、O (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical co
5、mmittee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electro
6、technical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the me
7、mber bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identif
8、ying any or all such patent rights. ISO 15500-18 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 25, Vehicles using gaseous fuels. This second edition cancels and replaces the first edition (ISO 15500-18:2001), which has been technically revised. ISO 15500 consists of t
9、he following parts, under the general title Road vehicles Compressed natural gas (CNG) fuel system components: Part 1: General requirements and definitions Part 2: Performance and general test methods Part 3: Check valve Part 4: Manual valve Part 5: Manual cylinder valve Part 6: Automatic valve Part
10、 7: Gas injector Part 8: Pressure indicator Part 9: Pressure regulator Part 10: Gas-flow adjuster Part 11: Gas/air mixer Part 12: Pressure relief valve (PRV) Part 13: Pressure relief device (PRD) Part 14: Excess flow valve Part 15: Gas-tight housing and ventilation hose Part 16: Rigid fuel line in s
11、tainless steel Part 17: Flexible fuel line Part 18: Filter Part 19: Fittings ISO 2012 All rights reserved iii ISO 15500-18:2012(E) Part 20: Rigid fuel line in material other than stainless steel iv ISO 2012 All rights reserved ISO 15500-18:2012(E) Introduction For the purpose of this part of ISO 155
12、00, all fuel system components in contact with natural gas have been considered suitable for natural gas as defined in ISO 15403. However, it is recognized that miscellaneous components not specifically covered herein can be examined to meet the criteria of this part of ISO 15500 and tested accordin
13、g to the appropriate functional tests. All references to pressure in this part of ISO 15500 are considered to be gauge pressures unless otherwise specified. This part of ISO 15500 is based on a service pressure for natural gas used as fuel of 20 MPa 200 bar 1) settled at 15 C. Other service pressure
14、s can be accommodated by adjusting the pressure by the appropriate factor (ratio). For example, a 25 MPa (250 bar) service pressure system will require pressures to be multiplied by 1,25. 1) 1 bar = 0,1 MPa = 10 5Pa 1 MPa = 1 N/mm 2 . ISO 2012 All rights reserved v Road vehicles Compressed natural g
15、as (CNG) fuel system components Part 18: Filter 1 Scope This part of ISO 15500 specifies tests and requirements for the filter, a compressed natural gas (CNG) fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This part of ISO 15500 is applicable to vehicles (
16、mono-fuel, bi-fuel or dual-fuel applications) using natural gas in accordance with ISO 15403. It is not applicable to the following: a) liquefied natural gas (LNG) fuel system components located upstream of, and including, the vaporizer; b) fuel containers; c) stationary gas engines; d) container-mo
17、unting hardware; e) electronic fuel management; f) refuelling receptacles. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referen
18、ced document (including any amendments) applies. ISO 15500-1, Road vehicles Compressed natural gas (CNG) fuel system components Part 1: General requirements and definitions ISO 15500-2, Road vehicles Compressed natural gas (CNG) fuel system components Part 2: Performance and general test methods 3 T
19、 erms and definitio ns For the purposes of this document, the terms and definitions given in ISO 15500-1 apply. 4 Marking Marking of the component shall provide sufficient information to allow the following to be traced: a) the manufacturers or agents name, trademark or symbol; b) the model designat
20、ion (part number); c) the working pressure or pressure and temperature range; d) the direction of flow (when necessary for correct installation). INTERNATIONAL STANDARD ISO 15500-18:2012(E) ISO 2012 All rights reserved 1 ISO 15500-18:2012(E) The following additional markings are recommended: the typ
21、e of fuel; electrical ratings (if applicable); the symbol of the certification agency; the type approval number; the serial number or date code; reference to this part of ISO 15500. NOTE This information can be provided by a suitable identification code on at least one part of the component when it
22、consists of more than one part. 5 Construction and assembly The filter shall comply with the applicable provisions of ISO 15500-1 and ISO 15500-2, and with the tests specified in Clause 6 of this part of ISO 15500. If non-conductive materials are used, the filter shall be designed to take its conduc
23、tivity into account. 6 Tests 6.1 Applicability The tests required to be carried out are indicated in Table 1. Table 1 Applicable tests Test Applicable Test procedure as required by ISO 15500-2 Sp eci fic t est requirement s of this part of ISO 15500 Hydrostatic strength X X X (see 6.2) Leakage X X E
24、xcess torque resistance X X Bending moment X X Continued operation X X X (see 6.3) Corrosion resistance X X Oxygen ageing X X Electrical over-voltages Non-metallic material immersion X X Vibration resistance X X (see 6.4) Brass material compatibility X X 6.2 Hydrostatic strength Test the filter acco
25、rding to the procedure for testing hydrostatic strength specified in ISO 15500-2. The test pressure shall be 2,5 times the working pressure. 6.3 Continued operation Test the filter in accordance with the procedure for testing continued operation given in ISO 15500-2 for a total of 20 000 cycles. 2 I
26、SO 2012 All rights reserved ISO 15500-18:2012(E) Following cycling testing, perform the hydrostatic strength test in accordance with 6.2 of this part of ISO 15500. 6.4 Vibration resistance Vibrate the filter, pressurized to its working pressure and sealed at both ends, for 30 min along each of the t
27、hree orthogonal axes at the most severe resonant frequencies determined as follows: by an acceleration of 1,5 g; within a sinusoidal frequency range of 10 Hz to 500 Hz; with a sweep time of 10 min. If the resonance frequency is not found in this range, the test shall be conducted at 500 Hz. At the c
28、ompletion of the test, the filter shall not show any indication of fatigue or component damage, and shall meet the leakage test requirements as specified in Clause 6 of ISO 15500-2. Following the leakage testing, perform the hydrostatic strength test in accordance with 6.2 of this part of ISO 15500.
29、 ISO 2012 All rights reserved 3 ISO 15500-18:2012(E) Bibliography 1 ISO 3833, Road vehicles Types Terms and definitions 2 ISO 15403-1, Natural gas Natural gas for use as a compressed fuel for vehicles Part 1: Designation of the quality 3 ISO/TR 15403-2, Natural gas Natural gas for use as a compressed fuel for vehicles Part 2: Specification of the quality 4 ISO 2012 All rights reservedISO 15500-18:2012(E) ISO 2012 All rights reserved ICS 43.060.40 Price based on 4 pages
