1、Reference number ISO 15534-1:2000(E) ISO 2000 INTERNATIONAL STANDARD ISO 15534-1 First edition 2000-02-15 Ergonomic design for the safety of machinery Part 1: Principles for determining the dimensions required for openings for whole-body access into machinery Conception ergonomique pour la scurit de
2、s machines Partie 1: Principes de dtermination des dimensions requises pour les ouvertures destines au passage de lensemble du corps dans les machinesISO 15534-1:2000(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed
3、or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liabil
4、ity in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is sui
5、table for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2000 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by an
6、y means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 734 10 79 E-mail
7、copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2000 All rights reservedISO 15534-1:2000(E) ISO 2000 All rights reserved iii Contents Page Foreword.iv Introduction.v 1 Scope 1 2 Normative references 1 3 General requirements2 4 Passage openings .2 4.1 Opening for horizontal forward movem
8、ent in upright posture.3 4.2 Opening for horizontal sideways movement over short distances in upright posture4 4.3 Vertical movement through a duct, using a ladder5 4.4 Manhole through which rapid active movement needs to be possible .6 4.5 Opening for entry in kneeling posture.6 Annex A (normative)
9、 Application of the measurements in practice7 Annex B (informative) Symbols for dimensions and anthropometric body measurements.10 Bibliography12ISO 15534-1:2000(E) iv ISO 2000 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national
10、 standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Internationa
11、l organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules
12、given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possib
13、ility that some of the elements of this part of ISO 15534 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 15534-1 was prepared by Technical Committee ISO/TC 159, Ergonomics, Subcommittee SC 3, Anthropome
14、try and biomechanics. ISO 15534 consists of the following parts, under the general title Ergonomic design for the safety of machinery: Part 1: Principles for determining the dimensions required for openings for whole-body access into machinery Part 2: Principles for determining the dimensions requir
15、ed for access openings Part 3: Anthropometric data Annex A forms a normative part of this part of ISO 15534. Annex B is for information only.ISO 15534-1:2000(E) ISO 2000 All rights reserved v Introduction This part of ISO 15534 is one of several ergonomics standards for the safety of machinery. EN 6
16、14-1 (2 in the Bibliography) describes the principles designers should adopt in order to take account of ergonomic factors. This part of ISO 15534 describes how these principles should be applied to the design of openings which will allow whole-body access. This part of ISO 15534 is based on EN 547-
17、1:1996 that was prepared as a harmonized standard conforming with the Machinery Directive and associated European Free Trade Association (EFTA) regulations.INTERNATIONAL STANDARD ISO 15534-1:2000(E) ISO 2000 All rights reserved 1 Ergonomic design for the safety of machinery Part 1: Principles for de
18、termining the dimensions required for openings for whole-body access into machinery 1 Scope This part of ISO 15534 specifies the dimensions of openings for whole-body access into machinery as defined in ISO/TR 12100-1. It provides the dimensions to which the values given in ISO 15534-3 are applicabl
19、e. Values for additional space requirements are given in annex A. This part of ISO 15534 has been prepared primarily for non- mobile machinery; there may be additional specific requirements for mobile machinery. Dimensions for passages are based on the values for either the 95th or the 99th percenti
20、les of the expected user population. Values for the 99th percentile apply to emergency egress routes. The anthropometric data given in ISO 15534-3 originate from static measurements of nude persons and do not take into account body movements, clothing, equipment, machinery-operating conditions or en
21、vironmental conditions. This part of ISO 15534 shows how to combine the anthropometric data with suitable allowances to take these factors into account. Situations where people are to be prevented from reaching a hazard are dealt with in ISO 13852. 2 Normative references The following normative docu
22、ments contain provisions which, through reference in this text, constitute provisions of this part of ISO 15534. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 15534 are encouraged to i
23、nvestigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO/TR 12100-1:1
24、992, Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology. (EN 292-1:1991) ISO 13852:1996, Safety of machinery Safety distances to prevent danger zones being reached by the upper limbs. (EN 294:1992) ISO 15534-3:2000, Ergonomic design for the safet
25、y of machinery Part 3: Anthropometric data.ISO 15534-1:2000(E) 2 ISO 2000 All rights reserved 3 General requirements This part of ISO 15534 specifies the relevant dimensions of openings with respect to different body positions. In arriving at values for these dimensions, in addition to the basic ant
26、hropometirc data, it is necessary to add allowances to permit unhindered and safe entry and working, taking into account aspects specific to the operator and to the operating conditions. In this respect the following criteria are of particular significance: a) ease of passage of a person is influenc
27、ed by the type of clothing, e.g. light or heavy clothing, whether tools are being carried, e.g. for maintenance or repair purposes, whether additional equipment, such as personal protective equipment (including protective clothing), or portable lighting, is being carried or worn, the demands of the
28、task, e.g. posture, nature and speed of movement, lines of sight, application of force, frequency and duration of task, length of passage, e.g. through a relatively thin wall (wall of a vessel) where there is space for movement at the exit or through a channel-type passage, amount of space available
29、 to allow for the dynamic nature of movement to escape from danger, the position and size of supports for the body, e.g. foot support, hand holds; b) environmental conditions (e.g. darkness, heat, noise, moisture), c) level of risk during the task. The allowances to be made for these items will depe
30、nd on the particular machinery concerned and its application. Annex A provides the application on how to apply this part of ISO 15534 in practice. Annex B gives information on the use of symbols for dimensions and anthropometric measurements. 4 Passage openings A passage opening is an opening which
31、allows the movement or the entry of a persons entire body, to enable the person to carry out measures such as operating of control actuators, monitoring of work processes and inspection of work results. See Figures 1 to 6. This part of ISO 15534 specifies minimum, not optimum, dimensions for opening
32、s. SAFETY PRECAUTIONS Wherever possible, from the safety point of view, the dimensions should be increased. Furthermore, passage openings should be sufficiently large to allow rapid egress in the event of danger. The allowances x and y in 4.1 to 4.5 are given in annex A. The values for a 1 , h 1 , e
33、tc. are given in ISO 15534-3.ISO 15534-1:2000(E) ISO 2000 All rights reserved 3 Symbol Explanation of measurement 4.1 Opening for horizontal forward movement in upright posture Figure 1 A B h 1 a 1 x y A = h 1 (P95 1 or P99 2 )+x B = a 1 (P95 or P99) + y Opening height Opening width Body height Elbo
34、w-to-elbow breadth Height allowance Width allowance 1) P95: 95th percentile of the expected user population. 2) P99: 99th percentile of the expected user population.ISO 15534-1:2000(E) 4 ISO 2000 All rights reserved Symbol Explanation of measurement 4.2 Opening for horizontal sideways movement over
35、short distances in upright posture Figure 2 A B h 1 b 1 x y Not applicable for emergency egress routes A = h 1 (P95) + x B = b 1 (P95) + y Opening height Opening width Body height Body depth Height allowance Width allowanceISO 15534-1:2000(E) ISO 2000 All rights reserved 5 Symbol Explanation of meas
36、urement 4.3 Vertical movement through a duct, using a ladder Figure 3 Figure 4 A B C c 1 c 2 x D a 1 y A = c 1 (P95 or P99) + x B =0,74 c 2 (P95) C = A + B Opening width 3 Clearance for foot Duct width Thigh length Foot length Width allowance D = a 1 (P95 or P99) + y Opening breadth Elbow-to-elbow b
37、readth Breadth allowance 3) Opening width A does not take account of the need for protection from falling.ISO 15534-1:2000(E) 6 ISO 2000 All rights reserved Symbol Explanation of measurement 4.4 Manhole through which rapid active movement needs to be possible Figure 5 A B a 1 x A = a 1 (P95 or P99)
38、+ x Opening diameter Length of the passage should be less than 500 mm Elbow-to-elbow breadth Allowance 4.5 Opening for entry in kneeling posture Figure 6 A B b 2 a 1 x y A = b 2 (P95 or P99) + x B = a 1 (P95 or P99) + y Opening height Opening width Forward reach (grip reach) Elbow-to-elbow breadth H
39、eight allowance Width allowanceISO 15534-1:2000(E) ISO 2000 All rights reserved 7 Annex A (normative) Application of the measurements in practice A.1 Introduction The purpose of this annex is to explain how to apply the anthropometric measurements given in this part of ISO 15534 according to ergonom
40、ic and safety and health principles. This part of ISO 15534 describes minimum dimensions for openings based on anthropometric measurements, i.e. static measurements of nude persons. The opening dimensions, including allowances, in this part of ISO 15534 do not always take into consideration, for exa
41、mple: aspects of health and safety arising from contact with the passage opening itself; whether the body positions and movements that must be used in the passage mean any risk to the users safety and health, e.g. in relation to how often or how long the person has to use the passage; whether the pe
42、rson has to adopt a certain body position in order to meet the force demands of the task without becoming overloaded; the space required for transportation of equipment, tools and injured or unconscious persons through the passage; the space required for using equipment and tools in the passage in a
43、 proper ergonomic way, e.g. cleaning, repair and maintenance work; personal protective equipment the user might wear when passing through the passage; the space requirements for entrance to and exit from the passage. The design of a passage that takes ergonomic principles into proper consideration u
44、sually leads to more efficient work, which is also of economic benefit. For example, in most cases the operation time increases as the size of the opening decreases. A.2 Principles for determining additional space For each of the openings in this part of ISO 15534, a number of allowances are describ
45、ed in clause A.3 for conditions that need to be taken into consideration when determining the practical size of a specific passage. Where they are applicable, these conditions determine allowances which shall be added to the anthropometric measurements in order to ensure safety and health while usin
46、g the passage. These allowances are not simply additive; some of the conditions overlap. When designing a specific passage, consideration shall be given to each condition given in clause A.3. A decision has to be made as to which ones are applicable and which ones are the most critical and then an i
47、ntegration of the factors shall be made by an expert, ending with a definite figure on the total allowance required in each direction.ISO 15534-1:2000(E) 8 ISO 2000 All rights reserved A.3 Additional space requirements for openings A.3.1 Opening for horizontal forward movement in upright posture (se
48、e 4.1) The following allowances shall be added, where appropriate, to the anthropometric measurements given in ISO 15534-3. Height allowance x for basic allowance for body movement . 50 mm fast walking or running or frequent or long-duration use. 100 mm shoes or heavy footwear 40 mm personal protect
49、ive equipment which add height to the person, e.g. helmets 60 mm Width allowance y for basic allowance for body movement 50 mm fast walking or running or frequent or long-duration use 100 mm working clothes . 20 mm clothes that will be damaged by contact with the passage walls . 100 mm heavy winter clothing or personal protective clothing . 100 mm transportation of injured person 200 mm A.3.2 Opening for horizontal sideways movement over short distances
