1、 Reference number ISO 15745-3:2003(E) ISO 2003INTERNATIONAL STANDARD ISO 15745-3 First edition 2003-11-15 Industrial automation systems and integration Open systems application integration framework Part 3: Reference description for IEC 61158-based control systems Systmes dautomatisation industriell
2、e et intgration Cadres dintgration dapplication pour les systmes ouverts Partie 3: Description de rfrence pour les systmes de contrle fonds sur la CEI 61158 ISO 15745-3:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be p
3、rinted or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no
4、 liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file
5、 is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form o
6、r by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47
7、E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2003 All rights reservedISO 15745-3:2003(E) ISO 2003 All rights reserved iiiContents Page Forewordv Introduction vi 1 Scope1 2 Normative references1 3 Terms and definitions2 4 Abbreviated terms3 5 Technology specific elements an
8、d rules.4 5.1 Integration models and IAS interfaces 4 5.2 Profile templates4 5.2.1 General4 5.2.2 Contents and syntax4 5.2.3 Header.5 5.3 Technology specific profiles 5 6 Device and communication network profiles for IEC61158-based control systems .6 6.1 ControlNet.6 6.1.1 Device profile6 6.1.2 Comm
9、unication network profile.8 6.2 PROFIBUS.10 6.2.1 Device profile10 6.2.2 Communication network profile.10 6.3 P-NET12 6.3.1 Device profile12 6.3.2 Communication network profile.13 6.4 WorldFIP.15 6.4.1 Device profile15 6.4.2 Communication network profile.18 6.5 INTERBUS.25 6.5.1 Device profile25 6.5
10、.2 Communication network profile.32 Annex A (normative) ControlNet profile templates 36 A.1 General36 A.2 Device profile template description .37 A.2.1 Device profile template description XML based37 A.2.2 Device profile template description XML encapsulation of EDS files .55 A.3 Communication netwo
11、rk profile template description.57 A.3.1 Communication network profile template description XML based .57 A.3.2 Communication network profile template description XML encapsulation of EDS files 75 A.4 Electronic Data Sheet (EDS) .76 A.4.1 Common CIP EDS requirements 76 A.4.2 ControlNet specific EDS
12、requirements116 Annex B (normative) PROFIBUS profile templates .121 B.1 General121 B.2 Device profile template description .121 B.2.1 General121 B.2.2 XML schema: GSD_Device_Profile_wrapper.xsd or EDD_Device_Profile_wrapper.xsd .122 B.3 Communication network profile template description.124 B.3.1 Ge
13、neral124 B.3.2 XML schema: GSD_CommNet_Profile_wrapper.xsd .124 B.4 Generic Station Description (GSD) 125 ISO 15745-3:2003(E) iv ISO 2003 All rights reservedB.4.1 General. 125 B.4.2 Syntax and format of the GSD files. 126 B.5 Semantic of GSD . 127 B.5.1 Conventions. 127 B.5.2 General specifications
14、128 B.5.3 Master-related specifications. 135 B.5.4 Slave-related specifications. 142 B.6 Formal description of GSD. 165 Annex C (normative) P-NET profile templates . 179 C.1 Device profile template description 179 C.2 Communication network profile template description 181 Annex D (normative) WorldFI
15、P profile templates 184 D.1 Device profile template description 184 D.1.1 Overview 184 D.1.2 DeviceConformityClass 184 D.1.3 Device profile template XML schema 187 D.2 Communication network profile template description 190 D.2.1 Overview 190 D.2.2 Application layers. 190 D.2.3 Transport layers; DLCo
16、nformityClass 193 D.2.4 Network Management. 194 D.2.5 Communication network profile template XML schema . 196 Annex E (normative) INTERBUS profile templates 205 E.1 Device profile template description 205 E.1.1 Overview 205 E.1.2 Basics. 205 E.1.3 DeviceIdentity object - deviceType object 207 E.1.4
17、DeviceManager object 209 E.1.5 Supplementary element descriptions. 214 E.1.6 Device profile template XML schemas 217 E.2 Communication network profile template description 264 Bibliography . 269 ISO 15745-3:2003(E) ISO 2003 All rights reserved vForeword ISO (the International Organization for Standa
18、rdization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right t
19、o be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Sta
20、ndards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an In
21、ternational Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 1574
22、5-3 was prepared by Technical Committee ISO/TC 184, Industrial automation systems and integration, Subcommittee SC 5, Architecture, communications and integration frameworks. ISO 15745 consists of the following parts, under the general title Industrial automation systems and integration Open systems
23、 application integration framework: Part 1: Generic reference description Part 2: Reference description for ISO 11898-based control systems Part 3: Reference description for IEC 61158-based control systems Part 4: Reference description for Ethernet-based control systems ISO 15745-3:2003(E) vi ISO 20
24、03 All rights reservedIntroduction The application integration framework (AIF) described in ISO 15745 defines elements and rules that facilitate: the systematic organization and representation of the application integration requirements using integration models; the development of interface specific
25、ations in the form of application interoperability profiles (AIPs) that enable both the selection of suitable resources and the documentation of the “as built“ application. ISO 15745-1 defines the generic elements and rules for describing integration models and AIPs, together with their component pr
26、ofiles - process profiles, information exchange profiles, and resource profiles. The context of ISO 15745 and a structural overview of the constituents of an AIP are given in Figure 1 of ISO 15745-1:2003. This part of ISO 15745 extends the generic AIF described in ISO 15745-1 by defining the technol
27、ogy specific elements and rules for describing both communication network profiles and the communication related aspects of device profiles specific to control systems based on IEC 61158 (P-NET 1 , PROFIBUS 2 , WorldFIP 3 , ControlNet TM 4 , and INTERBUS 5 ). These technologies use profiles of IEC 6
28、1158 which are specified in IEC 61784-1. Profiles for ISO/IEC 8802-3-based control systems are outside the scope of this part of ISO 15745 and are specified in ISO 15745-4. In particular, this part of ISO 15745 describes technology specific profile templates for the device profile and the communicat
29、ion network profile. Within an AIP, a device profile instance or a communication network profile instance is part of the resource profile defined in ISO 15745-1. The device profile and the communication network profile XML instance files are included in a resource profile XML instance using the Prof
30、ileHandle_DataType as specified in ISO 15745-1:2003, 7.2.5. 1P-NET is the registered trademark of the International P-NET User Organisation Aps (IPUO). Control of trademark use is given to the non profit organisation IPUO. This information is given for the convenience of users of this International
31、Standard and does not constitute an endorsement by ISO of the trademark holder or any of its products. Compliance to this standard does not require use of the trademark P-NET. Use of the trademark P-NET requires permission of the IPUO 2PROFIBUS is the trade name of the PROFIBUS Nutzerorganisation e.
32、V. (PNO), control of trade name use is given to the non profit organisation PNO. This information is given for the convenience of users of this International Standard and does not constitute an endorsement by ISO of the trademark holder or any of its products. Compliance to this standard does not re
33、quire use of the trade name PROFIBUS. Use of the trade name PROFIBUS requires permission of the PNO. 3WorldFIP is a registered trademark of the WorldFIP Association. Control of trademark use is given to the non profit organisation WorldFIP Association. This information is given for the convenience o
34、f users of this International Standard and does not constitute an endorsement by ISO of the trademark holder or any of its products. Compliance to this standard does not require use of the trademark WorldFip. Use of the trademark WorldFIP requires permission of the WorldFIP Association. 4ControlNet
35、is a trade name of ControlNet International, Ltd. This information is given for the convenience of users of ISO 15745 and does not constitute an endorsement by ISO of the trademark holder or any of its products. Compliance to this standard does not require use of the trade name ControlNet. Use of th
36、e trade name ControlNet requires permission of ControlNet International, Ltd. 5INTERBUS is a trade name of Phoenix Contact GmbH & Co. KG, control of trade name use is given to the non profit organisation INTERBUS Club. This information is given for the convenience of users of this International Stan
37、dard and does not constitute an endorsement by ISO of the trademark holder or any of its products. Compliance to this standard does not require use of the trade name INTERBUS. Use of the trade name INTERBUS requires permission of the INTERBUS Club. AIFs specified using the elements and rules of ISO
38、15745-1 can be easily integrated with the component profiles defined using the elements and rules specified in this part. INTERNATIONAL STANDARD ISO 15745-3:2003(E) ISO 2003 All rights reserved 1Industrial automation systems and integration Open systems application integration framework Part 3: Refe
39、rence description for IEC 61158-based control systems 1 Scope This part of ISO 15745 defines the technology specific elements and rules for describing both communication network profiles and the communication related aspects of device profiles specific to IEC 61158-based control systems. Profiles fo
40、r ISO/IEC 8802-3-based control systems are outside the scope of this part of ISO 15745. NOTE Generic elements and rules for describing integration models and application interoperability profiles, together with their component profiles (process profiles, information exchange profiles, and resource p
41、rofiles) are specified in ISO 15745-1. This part of ISO 15745 is to be used in conjunction with ISO 15745-1 to describe an application integration framework. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only t
42、he edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 639-1:2002, Codes for the representation of names of languages Part 1: Alpha-2 code ISO 639-2:1998, Codes for the representation of names of languages Part 2: Alpha
43、-3 code ISO 3166-1:1997, Codes for the representation of names of countries and their subdivisions Part 1: Country codes ISO 9506-1:2000, Industrial automation systems Manufacturing Message Specification Part 1: Service definition ISO 15745-1:2003, Industrial automation and systems integration Open
44、systems application integration framework Part 1: Generic reference description ISO/IEC 10646-1:2000, Information technology Universal Multiple-Octet Coded Character Set (UCS) Part 1: Architecture and Basic Multilingual Plane IEC 61131-3:2003, Programmable controllers Part 3: Programming languages I
45、EC 61158 (all parts), Digital data communications for measurement and control Fieldbus for use in industrial control systems IEC 61784-1:2003, Digital data communications for measurement and control - Part 1: Profile sets for continuous and discrete manufacturing relative to fieldbus use in industri
46、al control systems ISO 15745-3:2003(E) 2 ISO 2003 All rights reservedIEC 61804-2, Function blocks (FB) for process control Part 2: Specification of FB concept and electronic device description language (EDDL) 6 ANSI TIA/EIA-232-F:1997, Interface Between Data Terminal Equipment and Data Circuit-Termi
47、nating Equipment Employing Serial Binary Data Interchange ANSI TIA/EIA-485-A:1998, Electrical Characteristics of Generators and Receivers for Use in Balanced Digital Multipoint Systems EN 50170:1996 Volume 3 Part 7-3, General purpose field communication system WorldFIP Network Management IEEE Std 75
48、4-1985 (R1990), IEEE Standard for Binary Floating Point Arithmetic REC-xml-20001006, Extensible Markup Language (XML) 1.0 Second Edition W3C Recommendation 6 October 2000 REC-xmlschema-1-20010502, XML Schema Part 1: Structures W3C Recommendation 02 May 2001 REC-xmlschema-2-20010502, XML Schema Part
49、2: Datatypes W3C Recommendation 02 May 2001 RFC 1738:1994, Uniform Resource Locators (URL) Internet Engineering Task Force (IETF), Request for Comments (RFC) RFC 1759:1995, Printer MIB Internet Engineering Task Force (IETF), Request for Comments (RFC) UML V1.4, OMG - Unified Modeling Language Specification (Version 1.4, September 2001) 3 Terms and definitions NOTE The UML terminology and notation used in this document is described in Annex A of ISO 15745-1:2003. Fo
