1、 ISO 2013 Plywood Tolerances on dimensions Contreplaqu Tolrances sur dimensions INTERNATIONAL STANDARD ISO 1954 Second edition 2013-11-01 Reference number ISO 1954:2013(E) ISO 1954:2013(E)ii ISO 2013 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2013 All rights reserved. Unless otherwise spec
2、ified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or I
3、SOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ISO 1954:2013(E) ISO 2013 All rights reserved iii Contents Page Foreword iv 1 Scope .
4、1 2 Normative references 1 3 Moisture content of panels 1 4 Tolerances . 1 4.1 General . 1 4.2 Tolerances on length and width . 1 4.3 Tolerances on thickness 1 4.4 Tolerance on straightness of edges . 2 4.5 Tolerance on squareness 2 ISO 1954:2013(E) Foreword ISO (the International Organization for S
5、tandardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the ri
6、ght to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedur
7、es used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial r
8、ules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights ide
9、ntified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanati
10、on on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information. The committee responsible for this documen
11、t is ISO/TC 89, Wood-based panels , Subcommittee SC 3, Plywood. This second edition cancels and replaces the first edition (ISO 1954:1999), Clauses 3, 4, and 5 of which have been technically revised.iv ISO 2013 All rights reserved INTERNATIONAL ST ANDARD ISO 1954:2013(E) Plywood Tolerances on dimens
12、ions 1 Scope This International Standard specifies dimensional tolerances of plywood panels (length, width, thickness) and tolerances for edge straightness and squareness. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispe
13、nsable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 9426, Wood-based panels Determination of dimensions of panels ISO 16979, Wood-based panels Determination of
14、moisture content 3 Moisture content of panels Moisture content shall be measured in accordance with ISO 16979. Unless otherwise stated by contract, dimensional tolerances are applicable at a reference moisture content of (10 2) %. Statistically valid factors may be used to adjust measurements that c
15、an be taken, for practical purposes, at different moisture content (e.g. as-manufactured state or as-received state). 4 Tolerances 4.1 General Unless otherwise specified in other applicable standards, specifications, and/or contract terms, the tolerances given in 4.2 to 4.5 shall apply. NOTE Some pl
16、ywood products and uses can require narrower tolerances. 4.2 Tolerances on length and width Length and width shall be measured in accordance with ISO 9426. Tolerances on nominal size: 1,5 mm/m with a maximum of 3,5 mm. 4.3 Tolerances on thickness Thickness shall be measured in accordance with ISO 94
17、26. Tolerances on nominal thickness are specified in Table 1. ISO 2013 All rights reserved 1 ISO 1954:2013(E) Table 1 Tolerances on nominal thickness Dimensions in millimetres Nominal thickness t Unsanded, touch-sanded, or scraped panels Sanded panels Thickness tolerance within one panel Tolerance o
18、n nominal thickness Thickness tolerance within one panel Tolerance on nominal thickness t 3 0,5 +0,4 0,2 0,3 0,2 3 25 1,5 +(0,8 + 0,03 t) (0,4 + 0,03 t) 0,8 +(0,2 + 0,03 t) (0,3 + 0,03 t) 4.4 Tolerance on straightness of edges Straightness of panel edges shall be measured in accordance with ISO 9426. Tolerance: 1 mm/m. 4.5 Tolerance on squareness Squareness shall be measured in accordance with ISO 9426. Tolerance: 1 mm/m.2 ISO 2013 All rights reserved ISO 1954:2013(E) ISO 2013 All rights reserved IC S 79.060.10 Price based on 2 pages
