1、 Reference number ISO 23552-1:2007/Amd.1:2010(E) ISO 2010INTERNATIONAL STANDARD ISO 23552-1 First edition 2007-10-15 AMENDMENT 1 2010-10-01 Safety and control devices for gas and/or oil burners and gas and/or oil appliances Particular requirements Part 1: Fuel/air ratio controls, electronic type AME
2、NDMENT 1: Addition to the specific regional requirements in Japan Dispositifs de commande et de scurit pour brleurs gaz et/ou fioul et pour appareils gaz et/ou fioul Exigences particulires Partie 1: Dispositifs de rgulation du rapport air/combustible de type lectronique AMENDEMENT 1: Addition aux ex
3、igences spcifiques rgionales au Japon ISO 23552-1:2007/Amd.1:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and install
4、ed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software product
5、s used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, ple
6、ase inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm,
7、 without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2010 Al
8、l rights reservedISO 23552-1:2007/Amd.1:2010(E) ISO 2010 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
9、ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates
10、 closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards.
11、 Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this
12、document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Amendment 1 to ISO 23552-1:2007 was prepared by Technical Committee ISO/TC 161, Control and protective devices for gas and/or oil burners and applicances. ISO 23552-1:2007/A
13、md.1:2010(E) ISO 2010 All rights reserved 1Safety and control devices for gas and/or oil burners and gas and/or oil appliances Particular requirements Part 1: Fuel/air ratio controls, electronic type AMENDMENT 1: Addition to the specific regional requirements in Japan Page 20, Annex C Add the follow
14、ing before the first paragraph: Add the following sentence after the first paragraph in Clause 1: “This part of ISO 23552 is not applicable to electronic fuel/air ratio control systems used in industrial thermo- process and incineration application.” ISO 23552-1:2007/Amd.1:2010(E) ICS 27.060.20 Price based on 1 page ISO 2010 All rights reserved
