1、 ISO 2013 Intelligent transport systems Communications access for land mobiles (CALM) ITS station management Part 3: Service access points Systmes intelligents de transport Accs aux communications des services mobiles terrestres (CALM) Gestion des stations ITS Partie 3: Points daccs au service INTER
2、NATIONAL STANDARD ISO 24102-3 First edition 2013-07-01 Reference number ISO 24102-3:2013(E) ISO 24102-3:2013(E)ii ISO 2013 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2013 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in
3、 any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case po
4、stale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ISO 24102-3:2013(E) ISO 2013 All rights reserved iii Contents Page Foreword v Introduction vi 1 Scope . 1 2 Normative references 1 3 T erms and definitions . 2 4 A
5、bbreviated terms 2 5 Requirements 3 6 MI-SAP 3 6.1 General . 3 6.2 MI-SET 4 6.3 MI-GET . 5 6.4 MI-COMMAND . 6 6.5 MI-REQUEST . 7 6.6 MI-NOTIFY 8 7 MN-SAP 9 7.1 General . 9 7.2 MN-COMMAND . 9 7.3 MN-REQUEST 10 8 MF-SAP 11 8.1 General 11 8.2 MF-COMMAND .11 8.3 MF-REQUEST .13 9 SI-SAP .14 9.1 General 1
6、4 9.2 SI-COMMAND 14 9.3 SI-REQUEST 15 10 SN-SAP .16 10.1 General 16 10.2 SN-COMMAND 16 10.3 SN-REQUEST 17 11 SF-SAP 18 11.1 General 18 11.2 SF-COMMAND .19 11.3 SF-REQUEST .20 12 MS-SAP 21 12.1 General 21 12.2 MS-COMMAND .21 12.3 MS-REQUEST .22 13 Conformance 23 Annex A (normative) ASN.1 modules 24 A
7、nnex B (normative) MF-COMMANDs 36 Annex C (normative) MF-REQUESTs .39 Annex D (normative) MN-COMMANDs .42 Annex E (normative) MN-REQUESTs 44 Annex F (normative) MI-COMMANDs 47 ISO 24102-3:2013(E)iv ISO 2013 All rights reserved Annex G (normative) MI-REQUESTs 52 Annex H (normative) SF-COMMANDs 56 Ann
8、ex I (normative) SF-REQUESTs 57 Annex J (normative) SN-COMMANDs .58 Annex K (normative) SN-REQUESTs .59 Annex L (normative) SI-COMMANDs 60 Annex M (normative) SI-REQUESTs 61 Annex N (normative) MS-COMMANDs 62 Annex O (normative) MS-REQUESTs 63 Annex P (normative) Error/return codes 64 Bibliography .
9、65 ISO 24102-3:2013(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in
10、a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commissi
11、on (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents shou
12、ld be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identify
13、ing any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patents Any trade name used in this document is information given for the convenience of u
14、sers and does not constitute an endorsement. The committee responsible for this document is ISO/TC 204, Intelligent transport systems. ISO 24102 consists of the following parts, under the general title Intelligent transport systems Communications access for land mobiles (CALM) ITS station management
15、 Part 1: Local management Part 3: Service access points Part 4: ITS station-internal management communications Part 5: Fast service advertisement protocol (FSAP) The following parts are under preparation: Part 2: Remote management Part 6: Path and flow management ISO 2013 All rights reserved v ISO
16、24102-3:2013(E) Introduction This International Standard is part of a family of International Standards for communications access for land mobiles (CALM). An introduction to the whole set of International Standards is provided in ISO 21217. This part of ISO 24102 is part 3 of a multipart Internation
17、al Standard which determines the intelligent transport systems (ITS) station management service access points. The ITS station management entity provides functionality related to the management of communication protocol layers and the security entity presented in the ITS station reference architectu
18、re specified in ISO 21217 and presented in Figure 1, and in line with the general ITS architecture specified in ISO 21217. Communications Access Networking sent via the MI-SAP to the ITS-S access layer MI-REQUEST command issued by the ITS-S access layer and sent to the ITS-S management entity via th
19、e MI-SAP MI-SET command issued by the ITS-S management entity in order to set the value of one or several CI parameters; sent via the MI-SAP to the ITS-S access layer MN-COMMAND command issued by the ITS-S management entity and sent to the ITS-S networking and transport layer via the MN-SAP MN-REQUE
20、ST command issued by the ITS-S networking and transport layer and sent to the ITS-S management entity via the MN-SAP MS-COMMAND command issued by the ITS-S management entity and sent to the ITS-S security entity via the MS-SAP MS-REQUEST command issued by the ITS-S security entity and sent to the IT
21、S-S management entity via the MS-SAP SF-COMMAND command issued by the ITS-S security entity and sent to the ITS-S facilities layer via the SF-SAP SF-REQUEST command issued by the ITS-S facilities layer and sent to the ITS-S security entity via the SF-SAP SI-COMMAND command issued by the ITS-S securi
22、ty entity and sent to the ITS-S access layer via the SI-SAP SI-REQUEST command issued by the ITS-S access layer and sent to the ITS-S security entity via the SI-SAP SN-COMMAND command issued by the ITS-S security entity and sent to the ITS-S networking and transport layer via the SN-SAP SN-REQUEST c
23、ommand issued by the ITS-S networking and transport layer and sent to the ITS-S security entity via the SN-SAP2 ISO 2013 All rights reserved ISO 24102-3:2013(E) 5 Requirements The ITS station management includes functionality specified in the various parts of this International Standard: 1) General
24、management functionality specified in ISO 24102-1. 2) The functionality of remote ITS station management specified in ISO 24102-2. 3) The functionality of management/security service access points specified this part of ISO 24102. 4) The functionality of ITS station-internal management communication
25、s specified in ISO 24102-4. 5) The functionality of the “Fast Service Advertisement Protocol” (FSAP) specified in ISO 24102-5. The functionality of the service access points MI-SAP, MN-SAP, MF-SAP, SI-SAP, SN-SAP, SF-SAP, MS-SA P, shall be as specified in this part of ISO 24102. NOTE 1 SAPs can be n
26、on-exposed interfaces. Thus, service primitives of SAPs are not subject to conformance tests. NOTE 2 The MA-interface and SA-interface presented in Figure 1 are not specified in this part of ISO 24102, although these are recognized as part of the ITS station reference architecture specified in ISO 2
27、1217. All interfaces towards the ITS-S applications are considered to be APIs rather than SAPs. Means to secure the access to management functionality need to be specified within the global context of CALM security. Details are outside the scope of this part of ISO 24102. Detailed mandatory requirem
28、ents are specified in the following clauses of this part of ISO 24102: Clause 6 specifies the MI-SAP. Clause 7 specifies the MN-SAP. Clause 8 specifies the MF-SAP. Clause 9 specifies the SI-SAP. Clause 10 specifies the SN-SAP. Clause 11 specifies the SF-SAP. Clause 12 specifies the MS-SAP. Annexes p
29、rovide further mandatory requirements. 6 MI-SAP 6.1 General Basically, there are the following different types of services: a) a service that allows the ITS-S management entity to set I-Parameter values in a “(Virtual) Communication Interface” (CI, VCI), see ISO 21218; b) a service that allows the I
30、TS-S management entity to read I-Parameter values from a (virtual) CI; ISO 2013 All rights reserved 3 ISO 24102-3:2013(E) c) a service that allows a “Management Adaptation Entity” (MAE), see ISO 21218, to notify events to the ITS-S management, including changes in (virtual) CI I-Parameter values; d)
31、 a service that allows the ITS-S management entity to send a command to an MAE; e) a service that allows an MAE to send a command to the ITS-S management entity; f) a service for transmission requests of a management data packet; g) a service for reception notification of a management data packet. S
32、etting of I-Parameter values shall be built on the service MI-SET. Reading of I-Parameter values shall be built on the service MI-GET. Issuing of commands by the ITS-S management entity shall be built on the service MI-COMMAND. Issuing of commands by a CI or VCI shall be built on the service MI-REQU
33、EST. Transmission request and reception notification of management data packets shall be built on the services MI-COMMAND and MI-REQUEST. Event notifications shall be built on the service MI-REQUEST. Every request and confirm service primitive shall be identified by a CommandRef parameter. A value u
34、nique within the available number space shall be assigned to the request service primitive. The related confirm service primitive shall use the same number as provided in the related request service primitive. Management communications with the access layer in other ITS-SCUs shall be with Inter-ITS-
35、SCU communication PDUs “MI-rset”, “MI-rget”, “MI-rcmd”, and “MI-rreq” as specified in ISO 24102-4. Details of the service primitives shall be as specified in Annex A. 6.2 MI-SET 6.2.1 MI-SET.request The service primitive MI-SET.request allows setting of I-Parameters by the ITS-S management. The para
36、meters of MI-SET.request are as follows: MI-SET.request ( Link-ID, CommandRef, Sequence of I-Param ) Table 1 MI-SET.request parameter description Name Description Link-ID Unique identifier of a VCI/CI. CommandRef Unique cyclic reference number of command. - Number of subsequent elements I-Param. I-P
37、aram.No See ISO 21218. I-Param.Value See ISO 21218. An MI-SET.request is generated by the ITS-S management entity when I-Parameters specified in ISO 21218 shall be set. On receipt of MI-SET.request, the selected parameters shall be set if applicable.4 ISO 2013 All rights reserved ISO 24102-3:2013(E)
38、 6.2.2 MI- SET .c onfirm The service primitive MI-SET.confirm reports the result of a previous MI-SET.request. The parameters of MI-SET.confirm are as follows: MI-SET.confirm ( Link-ID, CommandRef, Sequence of Errors OPTIONAL ) The optional element “Sequence of Errors” shall be available once at lea
39、st one of the requested settings was in error. It may be available in order to acknowledge settings explicitly. T a b l e 2 M I - S E T . c o n f i r m p a r a m e t e r d e s c r i p t i o n Name Description Link-ID Unique identifier of a VCI/CI. CommandRef Unique cyclic reference number of command
40、 - Number of subsequent error messages. Errors.I-Par- amNo Parameter reference number for which Result.Code applies. Errors.errStatus Return/error code, see Table P.1. A request to set a defined “read only” I-Parameter shall be acknowledged with ErrStatus 7 “ACCESS VIOLATION”. A request to set an u
41、ndefined I-Parameter shall be acknowledged with ErrStatus 2 “INVALID PARAMETER NUMBER”. A request to set a defined I-Parameter with an illegal value shall be acknowledged with ErrStatus 3 “INVALID PARAMETER VALUE”. A request to set a defined I-Parameter with an illegal type of value shall be acknowl
42、edged with ErrStatus 1 “UNSPECIFIED FAILURE”. An MI-SET.confirm is generated by the MAE upon reception of a previous MI-SET.request. On receipt of MI-SET.confirm, the ITS-S management entity shall evaluate Errors, if applicable, and act accordingly. Details are outside the scope of this part of ISO
43、24102. 6.3 MI-GET 6.3.1 MI-GET.request The service primitive MI-GET.request requests reporting of I-Parameter values to the ITS-S management. The parameters of the management service primitive MI-GET.request are as follows: MI-GET.request ( Link-ID, CommandRef Sequence of I-ParamNo ) Table 3 MI-GET.
44、request parameter description Name Description Link-ID Unique identifier of a VCI/CI. CommandRef Unique cyclic reference number of command. - Number of subsequent elements I-Param.No. I-ParamNo See ISO 21218. This primitive is generated by the ITS-S management entity when I-Parameter values shall be retrieved. ISO 2013 All rights reserved 5
