1、 Reference number ISO 28239:2008(E) ISO 2008INTERNATIONAL STANDARD ISO 28239 First edition 2008-05-15 Textile machinery Opener and cleaner for staple fibres preparation Vocabulary and principles of construction Matriel pour lindustrie textile Ouvreuse et nettoyeuse pour la prparation des fibres disc
2、ontinues Vocabulaire et principes de construction ISO 28239:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installe
3、d on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products
4、 used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, plea
5、se inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm,
6、without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2008 All
7、 rights reservedISO 28239:2008(E) ISO 2008 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical
8、committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with
9、the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft Interna
10、tional Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may b
11、e the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 28239 was prepared by Technical Committee ISO/TC 72, Textile machinery and accessories, Subcommittee SC 1, Spinning preparatory, spinning, twisting and winding machinery and accessori
12、es. INTERNATIONAL STANDARD ISO 28239:2008(E) ISO 2008 All rights reserved 1Textile machinery Opener and cleaner for staple fibres preparation Vocabulary and principles of construction Scope This International Standard establishes a vocabulary of terms related to, and the principles of construction o
13、f, openers and cleaners used in the textile industry in the preparation for spinning of cotton and other staple fibres. Terms and definitions 1 Basic terms 1.1 opener machine with horizontally positioned opening roll, for opening of fibre material NOTE The opening roll concerned is opening roll 1 (3
14、4). See Annex A for construction variations. 1.2 cleaner machine with horizontally positioned opening rolls, for opening and cleaning of fibre material NOTE The opening rolls concerned are opening roll 1 (3.4), opening roll 2 (3.5) and opening roll 3 (3.6). See Annex A for construction variations.
15、2 Machine sides, dimensions (see Figure 1) 2.1 right side R machine side located to the right as seen facing toward the direction of fibre flow NOTE See also ISO 92. 2.2 left side L machine side located to the left as seen facing toward the direction of fibre flow NOTE See also ISO 92. 2.3 work flow
16、 direction material flow direction of fibre flow ISO 28239:2008(E) 2 ISO 2008 All rights reserved2.4 drive side side equipped with a cylinder drive Key a clear distance between front and back plate (inner distance between machine frames) b machine width (over casing) l machine length (without deposi
17、t system) R right side L left side 1 feed area (rear) Figure 1 Machine sides, dimensions 3 Machine components (see Figures 2 and 3) 3.1 feed lattice feed belt for feeding fibre material to the feed roll (3.3) 3.2 precondensing roll roll for condensing fibre material for the feed process 3.3 feed rol
18、l roll for transport and for clamping of fibre material, for feeding opening roll 1 (3.4) 3.4 opening roll 1 roll with pins that disengages tuft material from the stopped stroke 3.5 opening roll 2 opening and transfer roll, equipped with clothing ISO 28239:2008(E) ISO 2008 All rights reserved 33.6 o
19、pening roll 3 opening and transfer roll, equipped with clothing 3.7 mote knife knife for extracting impurities 3.8 carding element element equipped with clothing for pre-opening fibre tufts 3.9 deflector blade swivelling guide element for adjusting waste quantity 3.10 material suction device suction
20、 funnel for continuous suction of the opened and cleaned fibre material 3.11 waste suction suction funnel for continuous suction of extracted waste Figure 2 Machine components Opener ISO 28239:2008(E) 4 ISO 2008 All rights reservedFigure 3 Machine components Cleaner ISO 28239:2008(E) ISO 2008 All ri
21、ghts reserved 5Annex A (normative) Principles of construction (variations) A.1 Working width A.2 Opener A.2.1 Opener with one opening roll A.2.2 Opener with several opening rolls A.2.3 Universal opener A.3 Cleaner A.3.1 Cleaner with one roll A.3.2 Cleaner with several rolls A.3.3 Pre-cleaner A.3.4 Waste cleaner ISO 28239:2008(E) 6 ISO 2008 All rights reservedBibliography 1 ISO 92, Textile machinery and accessories Spinning machinery Definition of side (left or right) ISO 28239:2008(E) ICS 01.040.59; 59.120.10 Price based on 6 pages ISO 2008 All rights reserved
