1、Reference number ISO 841:2001(E) ISO 2001 INTERNATIONAL STANDARD ISO 841 Second edition 2001-10-15 Industrial automation systems and integration Numerical control of machines Coordinate system and motion nomenclature Systmes dautomatisation industrielle et intgration Commande numrique des machines S
2、ystmes de coordonnes et nomenclature du mouvementISO 841:2001(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed o
3、n the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products us
4、ed to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please
5、inform the Central Secretariat at the address given below. ISO 2001 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing fr
6、om either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2001 All rights reservedISO 841:2001(E) ISO
7、2001 All rights reserved iii Contents Page Foreword.iv Introduction.v 1 Scope 1 2 Normative references 1 3 Terms and definitions .1 4 Machine coordinate system1 4.1 Designation 1 4.2 Origin 2 4.3 Z axis.2 4.4 X axis.2 4.5 Y axis.3 4.6 Rotary axes A, B and C 3 5 Principal machine motions.3 5.1 Design
8、ation 3 5.2 Direction .3 6 Additional motions 4 6.1 Linear motions .4 6.2 Rotary motion.4 6.3 Letter restrictions 4 6.4 Direction .4 7 Schematic drawings of machines4 7.1 Examples of machine drawings .4 7.2 Designation 5 Annex A (normative) Examples of machine motions6ISO 841:2001(E) iv ISO 2001 All
9、 rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subj
10、ect for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IE
11、C) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Interna
12、tional Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
13、 International Standard ISO 841 was prepared by Technical Committee ISO/TC 184, Industrial automation systems and integration, Subcommittee SC 1, Physical device control. This second edition cancels and replaces the first edition (ISO 841:1984), which has been technically revised. The following chan
14、ges have been made: the content has been restructured in a more logical order; axes and motions have been clearly distinguished; new machine types have been added; motion designation for more complex machines has been added. Annex A forms a normative part of this International Standard.ISO 841:2001(
15、E) ISO 2001 All rights reserved v Introduction This International Standard defines a standard machine coordinate system and the machine motions so that a programmer can describe the machining operations without having to know whether the tool approaches the workpiece or the workpiece approaches the
16、tool. The standard machine coordinate system is used to provide the coordinates of a moving tool (or point in the working space or on a drawing) with respect to a stationary workpiece.INTERNATIONAL STANDARD ISO 841:2001(E) ISO 2001 All rights reserved 1 Industrial automation systems and integration
17、Numerical control of machines Coordinate system and motion nomenclature 1 Scope This International Standard describes a machine coordinate system related to the primary motions of individual numerically controlled machines and the associated machine motions. The machine coordinate system is used to
18、provide the coordinates of a moving tool (or a point in the working space or on the drawing) with respect to a stationary workpiece. Thus a programmer can describe the machine operations without having to know whether the tool approaches the workpiece or the workpiece approaches the tool. NOTE 1 Ind
19、ividual numerically controlled machines means that all axes are mounted on one base or frame and all motions are related to one standard coordinate system. NOTE 2 For the sake of simplicity the majority of the text of this International Standard is written in terms accorded to machine tools but neve
20、rtheless accorded to numerically controlled machines in general. Coordinate systems and axis motion nomenclature for industrial robots is defined in ISO 9787, Manipulating industrial robots Coordinate systems and motion nomenclatures. 2 Normative references The following normative documents contain
21、provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to inves
22、tigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 2806:1994, Indus
23、trial automation systems Numerical control of machines Vocabulary ISO 6983-1:1982, Numerical control of machines Program format and definition of address words Part 1: Data format for positioning, line motion and contouring control systems 3 Terms and definitions For the purposes of this Internation
24、al Standard, the terms and definitions given in ISO 2806 apply. 4 Machine coordinate system 4.1 Designation The machine coordinate system is a right-hand rectangular system with the three principal axes labelled X, Y and Z, with rotary axes about each of these axes labelled A, B and C, respectively
25、(see Figure A.1).ISO 841:2001(E) 2 ISO 2001 All rights reserved 4.2 Origin The location of the origin of the machine coordinate system shall be defined by the manufacturer. 4.3 Z axis 4.3.1 General The Z axis is parallel to the principal spindle of the machine. For the case where the machine has no
26、spindle, see 4.3.4 and 4.3.5. NOTE 1 On machines used for milling, grinding, boring, drilling and tapping, the spindle rotates the tool. NOTE 2 On machines such as lathes, cylindrical grinders and others which generate a surface of revolution, the spindle rotates the work piece. 4.3.2 More than one
27、spindle Where there are several spindles, one shall be selected as the principal spindle, preferably perpendicular to the workholding surface. 4.3.3 Swivelling or gimballing spindle Where the principal spindle can be swivelled or gimballed, the Z axis shall be parallel to spindle axis when the spind
28、le is in the zero position. The preferred zero position is with the spindle perpendicular to the work-holding surface. Where the principal spindle axis can be swivelled and if the extent of its motion allows it to lie in only one position parallel to one of the axes of the standard three-axis system
29、, this standard axis is the Z axis. Where the extent of the swivelling motion is such that the principal spindle can lie parallel to two of the three axes of the standard three-axis system, the Z axis is the standard axis which is perpendicular to the work holding surface of the work table of the ma
30、chine, ignoring such auxiliary devices as mounting brackets or angle plates. 4.3.4 No spindle For cutting and forming machines, the Z axis shall be perpendicular to the work-holding surface. For coordinate measuring machines, the Z axis should be collinear with the acceleration of gravity vector (i.
31、e. perpendicular to the surface of the earth). 4.3.5 Direction For cutting and forming machines, the Z axis direction is defined from the workpiece to the tool holder. NOTE For lathes, the tail stock is considered as the tool holder. For coordinate measuring machines, the Z direction is defined as i
32、n the opposite sense as the acceleration of gravity vector (i.e. pointing away from the surface of the earth). 4.4 X axis 4.4.1 General Where possible, the X axis shall be horizontal.ISO 841:2001(E) ISO 2001 All rights reserved 3 4.4.2 Machines with rotating tools Horizontal Z axis: Positive X shall
33、 be to the right when viewed in the negative Z direction. Vertical Z axis, single column: Positive X shall be to the right when viewed from the front of the machine into the column. Vertical Z axis, gantry type: Positive X shall be to the right when viewed from the principal spindle to the left-hand
34、 gantry support. See also note 1 in 4.3.1. 4.4.3 Machines with rotating workpieces The X axis shall be radial and parallel to the cross slide. The positive direction shall be away from the axis of rotation. See also note 2 in 4.3.1. 4.4.4 Machines with no spindle For cutting machines, positive X sha
35、ll be parallel to and in the principal direction of cutting. For coordinate measuring machines, positive X shall be defined by the manufacturer. 4.5 Y axis Positive Y shall be in the direction to make a right-hand set of coordinates (see Figure A.1). 4.6 Rotary axes A, B and C 4.6.1 Designation A, B
36、 and C define rotary axes about linear axes X, Y and Z respectively. 4.6.2 Direction Positive A, B and C are in the direction to advance right-hand screws in the positive X, Y and Z directions respectively (see Figure A.1). 5 Principal machine motions 5.1 Designation The principal linear motions of
37、the machine which are parallel to the axes of the machine coordinate system shall be designated X, Y and Z respectively. The principle machine rotary motions which are around one or more of the principal coordinate system axes shall be designated A, B and C respectively. 5.2 Direction 5.2.1 General
38、Motion in the positive direction of the linear or rotary axes increases the positive position values and decreases the negative position values.ISO 841:2001(E) 4 ISO 2001 All rights reserved Letter designations shall be used to denote movement of either the tool or the workpiece. 5.2.2 Moving the to
39、ol When moving the tool, the direction of movement and the axes directions are equal. Positive movements are designated with X, Y, Z, A, B,. 5.2.3 Moving the workpiece When moving the workpiece, the direction of movement and the axis direction are opposite. To indicate the opposite direction, positi
40、ve movements are designated with X , Y , Z , A , B (i.e. the axis direction X X of the workpiece movement). 6 Additional motions 6.1 Linear motions When, in addition to the primary linear motions X, Y and Z, there exists secondary linear motions parallel to the primary motions, these shall be design
41、ated U, V and W respectively. Similarly, for tertiary motions, they shall be designated P, Q and R respectively. When linear motions exist which are not (or may not be) parallel to X, Y and Z, they may be designated U, V, W, P, Q,o rR as is most convenient. The primary linear motions should be those
42、 nearest the principal spindle, the secondary the next nearest, and the tertiary are the farthest. For milling machines, the cutting-bit with respect to a facing slide should be designated U or P if these letters are available. For machines with multiple units or many parallel movements, the designa
43、tion of these motions may be indexed by using a letter and a number (e.g. X1, X2, .). The index shall be a positive integer greater than zero. The primary motion(s) may or may not have an index. Thus it is possible on one machine to have motions with and without indices. 6.2 Rotary motion When, in a
44、ddition to the primary rotary motions, there exists secondary rotary motions, either parallel to A, B,o rC or compounded or gimballed to A, B,o rC, they shall be designated D or E (if these letters are available). As with linear motions, rotary motions may be indexed (see 6.1). 6.3 Letter restrictio
45、ns Certain letters (e.g. G, M, F) shall not be used for motion (see ISO 6983-1). 6.4 Direction The rules given in 5.2 for determining the direction of principal machine motions shall apply to additional motions. 7 Schematic drawings of machines 7.1 Examples of machine drawings The schematic drawings
46、 of machines in annex A are the official interpretation for those machines. Where a conflict exists between the text of this International Standard and a given schematic, the schematic drawing shall take precedence.ISO 841:2001(E) ISO 2001 All rights reserved 5 7.2 Designation The schematic drawing
47、shows the machine coordinate system as appropriate to that machine together with the machine motions. Letters indicate axes and machine motions, arrows indicate positive directions.ISO 841:2001(E) 6 ISO 2001 All rights reserved Annex A (normative) Examples of machine motions Figure A.1 Right-hand co
48、ordinate systemISO 841:2001(E) ISO 2001 All rights reserved 7 Figure A.2 Parallel lathe (engine lathe) Figure A.3 Twin turret lathe with programmable tailstock Figure A.4 Vertical turning and boring latheISO 841:2001(E) 8 ISO 2001 All rights reserved Figure A.5 Milling machine with horizontal spindl
49、e Figure A.6 Milling machine with vertical spindleISO 841:2001(E) ISO 2001 All rights reserved 9 Figure A.7 Boring and milling machine with horizontal spindle Figure A.8 Milling machine with vertical spindleISO 841:2001(E) 10 ISO 2001 All rights reserved Figure A.9 Portal-type milling machine Figure A.10 Gantry-type milling machineISO 841:2001(E) ISO 2001 All rights reserved 11 Figure A.11 Planer-type horizontal boring machine Figur
