1、 Reference number ISO/IEC 19460:2003(E) ISO/IEC 2003INTERNATIONAL STANDARD ISO/IEC 19460 Second edition 2003-04-01Information technology Telecommunications and information exchange between systems Private Integrated Services Network Inter-exchange signalling protocol Single Step Call Transfer supple
2、mentary service Technologies de linformation Tlcommunications et change dinformation entre systmes Rseau priv intgration de services Protocole de signalisation dinterchange Service supplmentaire de transfert dappel pas unique ISO/IEC 19460:2003(E) PDF disclaimer This PDF file may contain embedded ty
3、pefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not inf
4、ringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were op
5、timized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO/IEC 2003 All rights reserved. Unless otherwise specifi
6、ed, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case
7、 postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO/IEC 2003 All rights reservedISO/IEC 19460:2003(E) ISO/IEC 2003 All rights reserved iii Contents Foreword v Introduction vi 1 Scope 1 2 Conformance 1 3 No
8、rmative references 1 4 Terms and definitions 2 4.1 External definitions 2 4.2 Other definitions 3 4.2.1 Rerouting number 3 4.2.2 Rerouting PINX 3 4.2.3 Transferred PINX 3 4.2.4 Transferred-To PINX 3 4.2.5 Transferring PINX 3 5 Acronyms 3 6 Signalling protocol for the support of SS-SSCT 4 6.1 SS-SSCT
9、 description 4 6.2 SS-SSCT operational requirements 4 6.2.1 Provision/Withdrawal 4 6.2.2 Requirements on a Transferring PINX 4 6.2.3 Requirements on a Rerouting PINX 4 6.2.4 Requirements on a Transferred PINX 4 6.2.5 Requirements on a Transferred-To PINX 4 6.2.6 Requirements on a Transit PINX 4 6.3
10、SS-SSCT coding requirements 5 6.3.1 Operations 5 6.3.2 Information elements 7 6.3.3 Messages 7 6.4 SS-SSCT state definitions 8 6.4.1 States at a Transferring PINX 8 6.4.2 States at a Rerouting PINX 8 6.4.3 States at a Transferred PINX 8 6.4.4 States at a Transferred-To PINX 8 6.5 SS-SSCT signalling
11、procedures 8 6.5.1 Actions at a Transferring PINX 8 6.5.2 Procedures at the Rerouting PINX 9 6.5.3 Actions at a Transferred PINX 11 6.5.4 Actions at a Transferred-To PINX 11 6.5.5 Actions at a Transit PINX 12 6.5.6 Subsequent actions at Transferred and Transferred-To PINX 12 6.6 SS-SSCT impact of in
12、terworking with public ISDNs 12 6.6.1 Actions at a Gateway PINX 12 6.7 SS-SSCT impact of interworking with non-ISDNs 12ISO/IEC 19460:2003(E) iv ISO/IEC 2003 All rights reserved 6.7.1 Actions at a Gateway PINX 12 6.8 Protocol Interactions between SS-SSCT and other supplementary services and ANFs 13 6
13、8.1 Calling Name Identification Presentation (SS-CNIP) 13 6.8.2 Connected Name Identification Presentation (SS-CONP) 13 6.8.3 Completion of Calls to Busy Subscribers (SS-CCBS) 13 6.8.4 Completion of Calls on No Reply (SS-CCNR) 13 6.8.5 CallForwarding Unconditional (SS-CFU) 13 6.8.6 Call Forwarding
14、Busy (SS-CFB) 13 6.8.7 Call Forwarding No Reply (SS-CFNR) 14 6.8.8 Call Deflection (SS-CD) 14 6.8.9 Call Transfer (SS-CT) 14 6.8.10 Path Replacement (ANF-PR) 14 6.8.11 Advice Of Charge (SS-AOC) 15 6.8.12 Call Offer (SS-CO) 16 6.8.13 Do Not Disturb (SS-DND) 16 6.8.14 Do Not Disturb Override (SS-DNDO)
15、 16 6.8.15 Recall (SS-RE) 16 6.8.16 Call Intrusion (SS-CI) 16 6.8.17 Call Interception (ANF-CINT) 16 6.8.18 Transit Counter (SS-TC) 16 6.8.19 Route Restriction Class (ANF-RRC) 17 6.8.20 Authentication of the PISN (SS-WTAN) 17 6.8.21 Authentication of a WTM user (SS-WTAT) 17 6.8.22 Wireless Terminal
16、Location Registration (SS-WTLR) 17 6.8.23 Wireless Terminal Mobility Incoming Call (ANF-WTMI) 17 6.8.24 Wireless Terminal Mobility Outgoing Call (ANF-WTMO) 17 6.8.25 Message Waiting Indication (SS-MWI) 17 6.8.26 User Mobility Incoming Call (ANF-PUMI) 17 6.8.27 User Mobility Outgoing Call (ANF-PUMO)
17、17 6.8.28 Private User Mobility - Registration (SS-PUMR) 17 6.8.29 Common Information (ANF-CMN) 17 6.8.30 Call Priority Interruption (Protection) (SS-CPI(P) 17 6.9 SS-SSCT Parameter values (Timers) 17 6.9.1 Timer T1 17 6.9.2 Timer T2 18 6.9.3 Timer T3 18 Annexes A - Protocol Implementation Conforman
18、ce Statement (PICS) proforma 19 B - Imported ASN.1 definitions 27 C - Examples of message sequences 28 D - Specification and Description Language (SDL) representation of procedures 33 E - Additional feature identifier in module Common-Information-Operations 42 F - Difference between Single Step Call
19、 Transfer and Call Transfer by Rerouting 43 G - ASN.1 definitions according to ITU-T Recs. X.208 / X.209 44ISO/IEC 19460:2003(E) ISO/IEC 2003 All rights reserved v Foreword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the speci
20、alized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical co
21、mmittees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. Internati
22、onal Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of the joint technical committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting.
23、Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or al
24、l such patent rights. ISO/IEC 19460 was prepared by ECMA (as ECMA-300) and was adopted, under a special “fast-track procedure”, by Joint Technical Committee ISO/IEC JTC 1, Information technology, in parallel with its approval by national bodies of ISO and IEC. This second edition cancels and replace
25、s the first edition (ISO/IEC 19460:2001), which has been technically revised. ISO/IEC 19460:2003(E) vi ISO/IEC 2003 All rights reserved Introduction This International Standard is one of a series of Standards defining services and signalling protocols applicable to Private Integrated Services Networ
26、ks (PISNs). The series uses ISDN concepts as developed by ITU-T and conforms to the framework of International Standards for Open Systems Interconnection as defined by ISO/IEC. This International Standard specifies the signalling protocol for use at the Q reference point in support of the Call Trans
27、fer supplementary service. The protocol defined in this International Standard forms part of the PSS1 protocol (informally known as QSIG). This International Standard is based upon the practical experience of ECMA member companies and the results of their active and continuous participation in the w
28、ork of ISO/IEC JTC 1, ITU-T, ETSI and other international and national standardization bodies. It represents a pragmatic and widely based consensus. ISO/IEC 2003 All rights reserved 1 1S c o p e This International Standard specifies the signalling protocol for the support of the Single Step Call Tra
29、nsfer supplementary service (SS-SSCT) at the Q reference point between Private Integrated Network services eXchanges (PINXs) connected together within a Private Integrated Services Network (PISN). SS-SSCT is a supplementary service which enables a user, user A, to transform an existing call between
30、user A and user B into a new call between user B and a user C whereby user A does not have a call established with user C prior to call transfer. The Q reference point is defined in ISO/IEC 11579-1. Service specifications are produced in three stages and according to the method specified in ETS 300
31、387. This International Standard contains the stage 3 specification for the Q reference point and satisfies the requirements identified by the stage 1 and stage 2 specifications in ISO/IEC 19459. The signalling protocol for SS-SSCT operates on top of the signalling protocol for basic circuit switche
32、d call control, as specified in ISO/IEC 11572, and uses certain aspects of the generic procedures for the control of supplementary services specified in ISO/IEC 11582. This International Standard also specifies additional signalling protocol requirements for the support of interactions at the Q refe
33、rence point between Single Step Call Transfer and other supplementary services and ANFs. This International Standard is applicable to PINXs which can interconnect to form a PISN. 2 Conformance In order to conform to this International Standard, a PINX shall satisfy the requirements identified in the
34、 Protocol Implementation Conformance Statement (PICS) proforma in annex A. Conformance to this International Standard includes conforming to those clauses that specify protocol interactions between SS-SSCT and other supplementary services and ANFs for which signalling protocols at the Q reference po
35、int are supported in accordance with the stage 3 standards concerned. 3 Normative references ISO/IEC 11571:1998, Information technology - Telecommunications and information exchange between systems - Private Integrated Services Networks - Addressing ISO/IEC 11572:2000, Information technology - Telec
36、ommunications and information exchange between systems - Private Integrated Services Network - Circuit mode bearer services - Inter-exchange signalling procedures and protocol ISO/IEC 11574:2000, Information technology - Telecommunications and information exchange between systems - Private Integrate
37、d Services Network - Circuit-mode 64 kbit/s bearer services - Service description, functional capabilities and information flows ISO/IEC 11579-1:1994, Information technology - Telecommunications and information exchange between systems - Private integrated services network - Part 1: Reference config
38、uration for PISN Exchanges (PINX) ISO/IEC 11582:2002, Information technology - Telecommunications and information exchange between systems - Private Integrated Services Network - Generic functional protocol for the support of supplementary services - Inter-exchange signalling procedures and protocol
39、 The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. INTERNATIONAL STANDARD ISO/IEC 19460:2003(E)Info
40、rmation technology Telecommunications and information exchange between systems Private Integrated Services Network Inter-exchange signalling protocol Single Step Call Transfer supplementary service ISO/IEC 19460:2003(E) 2 ISO/IEC 2003 All rights reserved ISO/IEC 13868:2003, Information technology -
41、Telecommunications and information exchange between systems - Private Integrated Services Network - Inter-exchange signalling protocol - Name identification supplementary services ISO/IEC 13869:2003, Information technology - Telecommunications and information exchange between systems - Private Integ
42、rated Services Network - Inter-exchange signalling protocol - Call Transfer supplementary service ISO/IEC 13873:2003, Information technology - Telecommunications and information exchange between systems - Private Integrated Services Network - Inter-exchange signalling protocol - Call Diversion suppl
43、ementary services ISO/IEC 13874:2003, Information technology - Telecommunications and information exchange between systems - Private Integrated Services Network - Inter-exchange signalling protocol - Path Replacement additional network feature ISO/IEC 15050:2003, Information technology - Telecommuni
44、cations and information exchange between systems - Private Integrated Services Network - Inter-exchange signalling protocol - Advice Of Charge supplementary services ISO/IEC 15054:2003, Information technology - Telecommunications and information exchange between systems - Private Integrated Services
45、 Network - Inter-exchange signalling protocol - Call Interception additional network feature ISO/IEC 15056:1997, Information technology - Telecommunications and information exchange between systems - Private Integrated Services Network - Inter-exchange signalling protocol - Transit counter additiona
46、l network feature ISO/IEC 15772:2003, Information technology - Telecommunications and information exchange between systems - Private Integrated Services Network - Inter-exchange signalling protocol - Common Information additional network feature ISO/IEC 15992:2003, Information technology - Telecommu
47、nications and information exchange between systems - Private Integrated Services Network - Inter-exchange signalling protocol - Call Priority Interruption and Call Priority Interruption Protection supplementary services ISO/IEC 19459:2001, Information technology - Telecommunications and information
48、exchange between systems - Private Integrated Services Network - Specification, functional model and information flows - Single Step Call Transfer Supplementary Service ETS 300 387:1994, Private Telecommunication Network (PTN); Method for the specification of basic and supplementary services ITU-T R
49、ec. I.112:1993, Vocabulary of terms for ISDNs ITU-T Rec. I.210:1993, Principles of telecommunication services supported by an ISDN and the means to describe them ITU-T Rec. Q.950:2000, Supplementary services protocols, structure and general principles ITU-T Rec. Z.100:1999, Specification and description language (SDL) 4 Terms and definitions For the purposes of this document, the following terms and definitions apply. 4.1 External definitions This International Standard uses the following terms defined in other
