MNOSZ 12408-1952 《锌半成品（锌）碾压成的六角合金锌棒》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

JUS K T3 050-1983 Complex snap gauges for diameters to 6 mm nominal si e《适用于标称尺寸小于6毫米的直径的复合卡尺》.pdf

JUS K T3 052-1978 Gaugesfor shafts Gap gauges range above 3 to and including 100 mm《轴杆用量规 适用直径范围为3-100毫米（含）的间隙规》.pdf

JUS K T3 052-1983 Snap gauges range above 5 to and including 160 mm nominal si e《适用于标称直径在5-160毫米（含）的卡规》.pdf

JUS K T3 055-1983 Snap gauges GO and NOT GO with insert above 100 to and including 180 mm nominal si e《适用于标称直径在100-180毫米（含）的插入式过端和不过端卡规》.pdf

JUS K T3 056-1983 Snap gauges GO and NOTGO with insert above 180 to and including 360 mm nominal si e《适用于标称直径为180-360毫米（含）的插入式过端和不过端卡规》.pdf

JUS K T3 060-1983 Snap gauges GO range above 5 to and including 100 mm nominal si e《适用于标称直径为5-100毫米（含）的过端卡规》.pdf

JUS K T3 061-1983 Snap gauges NOTGO range above 5 to and including 100mm nominal si e《适用于标称直径为5-100毫米（含）的不过端卡规》.pdf

JUS K T3 062-1983 Snap gauges GO and NOT GO range above 5 to and including 100 mm nominal si e《适用于标称直径在5-100毫米（含）的过端和不过端卡规》.pdf

JUS K T3 071-1983 GO ring gauges and setting ring gauges from 1 to and including 315 mm nominal diameter《适用于标称直径在1-315毫米（含）的过端环规和校正环规》.pdf