HD 22 3 S3-1995 Rubber Insulated Cables of Rated Voltages up to and Including 450 750 V Part 3 Heat Resistant Silicone Rubber Insulated Cables《额定电压450 750 V及以下的.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

TCVN 2573-1-2007 Agricultural tractors Rear-mounted power take-off types 1 2 and 3 Part 1 General specifications safety requirements dimensions for master shield and earance zone《农.pdf

TCVN 2573-2-2009 Agricultural tractors Rear-mounted power take-off types 1 2 and 3 Part 2 Narrow-track tractors dimensions for master shield and clearance zone《农业拖拉机 后置式动力输出1 2和3型 .pdf

TCVN 2573-3-2009 Agricultural tractors Rear-mounted power take-off types 1 2 and 3 Part 3 Main PTO dimensions and spline dimensions location of PTO《农业拖拉机 后置式动力输出1 2和3型 第3部分 主PTO尺寸和.pdf

TCVN 2575-1978 Friction brake Brake washer Measurement《摩擦制动器 制动垫圈 测量》.pdf

TCVN 258-1-2007 Metallic materials Vickers hardness test Part 1 Test method《金属材料 维氏硬度试验 第1部分 试验方法》.pdf

TCVN 258-2-2007 Metallic materials Vickers hardness test Part 2 Test merhod《金属材料 维氏硬度试验 第2部分 硬度计的检验与校准》.pdf

TCVN 258-3-2007 Metallic materials Vickers hardness test Part 3 Calibration of reference blocks《金属材料 维氏硬度试验 第3部分 标准硬度块的标定》.pdf

TCVN 258-4-2007 Metallic materials Vickers hardness test Part 4 Tables of hardness values《金属材料 维氏硬度试验 第4部分 硬度值表》.pdf

TCVN 260-2008 Geometrical Product Specifications(GPS) Linear and angular dimensioning and tolerancing + - limit specifications Step dimensions distances angular sizes and radii《产品几.pdf