HD 313 2 3 S1-1989 Base Materials for Printed Circuits-Part 2 Specifications Specification No 3 Epoxide Cellulose Paper Copper-Clad Laminated Sheet of Defined F.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

ASME STP-PT-007-2006 COMPARISON OF PRESSURE VESSEL CODES ASME SECTION VIII AND EN13445 Technical Commercial and Usage Comparison Design Fatigue Life Comparison《压力容器规程ASME第VIII节和EN1.pdf

ASME STP-PT-007-2006 COMPARISON OF PRESSURE VESSEL CODES ASME SECTION VIII AND EN13445 Technical Commercial and Usage Comparison Design Fatigue Life Comparison《压力容器规程ASME第VIII节和EN1_1.pdf

ASME STP-PT-011-2008 INTEGRITY MANAGEMENT OF STRESS CORROSION CRACKING IN GAS PIPELINE HIGH CONSEQUENCE AREAS《燃气管线高风险区的应力腐蚀裂痕的完整性管理》.pdf

ASME STP-PT-014-2008 IMPROVEMENT OF ASME NH FOR GRADE 91 NEGLIGIBLE CREEP AND CREEP FATIGUE《氢气基础设施应用复合容器标准制定的数据支持》.pdf

ASME STP-PT-021-2008 NON DESTRUCTIVE TESTING AND EVALUATION METHODS FOR COMPOSITE HYDROGEN TANKS《合成氢储罐用无损检测和评定方法》.pdf

ASME STP-PT-022-2008 COMPARISON AND VALIDATION OF CREEP-BUCKLING ANALYSIS METHODS《蠕变弯曲分析方法的比较和验证》.pdf

ASME STP-PT-023-2009 GUIDELINES FOR IN-SERVICE INSPECTION OF COMPOSITE PRESSURE VESSELS《复合压力容器运行中检查的指南》.pdf

ASME STP-PT-024-2008 DEVELOPMENT OF BASIC TIME-DEPENDENT ALLOWABLE STRESSES FOR CREEP REGIME IN SECTION VIII DIVISION I《第1部第VIII节中用于蠕变状况的基本时间依赖型许可应力发展》.pdf

ASME STP-PT-025-2009 EXTENDED FATIGUE EXEMPTION RULES FOR LOW CR ALLOYS INTO THE TIME-DEPENDENT RANGE FOR SECTION VIII DIV 2《VIII部分第2区用在时间附属区的低铬合金延长疲劳去除的规则》.pdf