1、 IEC/IEEE 62582-2 Edition 1.0 2011-08 INTERNATIONAL STANDARD Nuclear power plants Instrumentation and control important to safety Electrical equipment condition monitoring methods Part 2: Indenter modulus Centrales nuclaires de puissance Instrumentation et contrle-commande importants pour la sret Mt
2、hodes de surveillance de ltat des matriels lectriques Partie 2: Module indenter IEC/IEEE 62582-2:2011NORME INTERNATIONALE THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2011 IEC, Geneva, Switzerland Copyright 2011 IEEE All rights reserved. Unless otherwise specified, no part of this publication m
3、ay be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing being secured. Requests for permission to reproduce should be addressed to either IEC at the address below or IECs member National Committee in the
4、country of the requester or from IEEE. IEC Central Office Institute of Electrical and Electronics Engineers, Inc. 3, rue de Varemb 3 Park Avenue CH-1211 Geneva 20 New York, NY 10016-5597 Switzerland United States of America Email: inmailiec.ch Email: stds.iprieee.org Web: www.iec.ch Web: www.ieee.or
5、g About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About the IEEE IEEE is the worlds largest professional association dedicated to advancin
6、g technological innovation and excellence for the benefit of humanity. IEEE and its members inspire a global community through its highly cited publications, conferences, technology standards, and professional and educational activities. About IEC/IEEE publications The technical content of IEC/IEEE
7、publications is kept under constant review by the IEC and IEEE. Please make sure that you have the latest edition; corrigenda or amendments might have been published. g131 IEC catalogue of publications: www.iec.ch/searchpub The IEC online catalogue enables you to search by a variety of criteria (ref
8、erence number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. g131 IEEE products and services : www.ieee.org/go/shop IEEE publishes nearly a third of the worlds technical literature in electrical engineering, computer science, and electronics
9、. Browse the latest publications including standards, draft standards, standards collections, and much more. g131 IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also by monthly
10、 email. g131 Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary
11、online. g131 Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 . IEC/IEEE 62582-2 Edition
12、 1.0 2011-08 INTERNATIONAL STANDARD Nuclear power plants Instrumentation and control important to safety Electrical equipment condition monitoring methods Part 2: Indenter modulus Centrales nuclaires de puissance Instrumentation et contrle-commande importants pour la sret Mthodes de surveillance de
13、ltat des matriels lectriques Partie 2: Module indenter R ICS 27.120.20 ISBN 978-2-88912-667-5 INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE PRICE CODE CODE PRIX NORME INTERNATIONALE 2 62582-2 g148 IEC/IEEE:2011 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope and
14、 object 7 2 Terms and definitions . 7 3 Abbreviations and acronyms . 7 4 General description 8 5 Applicability, reproducibility, and complexity . 8 5.1 General . 8 5.2 Applicability . 8 5.3 Reproducibility 8 5.4 Complexity 9 6 Measurement procedure . 9 6.1 Stabilisation of the polymeric materials 9
15、6.2 Sampling and measurement locations . 9 6.3 Conditions for measurement 9 6.4 Instrumentation . 10 6.5 Calibration and tolerances . 11 6.6 Selection of measurement points . 11 6.7 Selection of probe velocity and maximum force . 11 6.8 Clamping . 11 6.9 Determination of the value of the indenter mo
16、dulus . 11 6.10 Reporting 12 Annex A (informative) Examples illustrating factors affecting the variation of the indenter modulus value . 14 Annex B (informative) Example of a measurement report for indenter measurements in laboratory . 18 Bibliography 19 Figure 1 A schematic representation of the ge
17、ometry and dimensions of the probe tip used in the indenter 10 Figure 2 Calculation of indenter modulus . 12 Figure A.1 Example of local variation of indenter modulus due to variation in equipment dimensions and construction 14 Figure A.2 Indenter values measured at different temperatures . 15 Figur
18、e A.3 Normalised indenter mean values . 16 Figure A.4 Example of change of indenter modulus value in laboratory conditions of a hygroscopic sample after removal from long-term exposure in a heat chamber 17 Figure A.5 Adaptation of a decay curve to the measured indenter modulus values in Figure A.4 .
19、 17 Figure B.1 Example of measured force vs displacement 18 62582-2 g148 IEC/IEEE:2011 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ NUCLEAR POWER PLANTS INSTRUMENTATION AND CONTROL IMPORTANT TO SAFETY ELECTRICAL EQUIPMENT CONDITION MONITORING METHODS Part 2: Indenter modulus FOREWORD 1) The Interna
20、tional Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electro
21、nic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees;
22、 any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEEE Standards documents are developed within IEEE Societies and Stand
23、ards Coordinating Committees of the IEEE Standards Association (IEEE-SA) Standards Board. IEEE develops its standards through a consensus development process, approved by the American National Standards Institute, which brings together volunteers representing varied viewpoints and interests to achie
24、ve the final product. Volunteers are not necessarily members of IEEE and serve without compensation. While IEEE administers the process and establishes rules to promote fairness in the consensus development process, IEEE does not independently evaluate, test, or verify the accuracy of any of the inf
25、ormation contained in its standards. Use of IEEE Standards documents is wholly voluntary. IEEE documents are made available for use subject to important notices and legal disclaimers (see http:/standards.ieee.org/IPR/disclaimers.html for more information). IEC collaborates closely with IEEE in accor
26、dance with conditions determined by agreement between the two organizations. This Dual Logo International Standard was jointly developed by the IEC and IEEE under the terms of that agreement. 2) The formal decisions of IEC on technical matters express, as nearly as possible, an international consens
27、us of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. The formal decisions of IEEE on technical matters, once consensus within IEEE Societies and Standards Coordinating Committees has been reached, is determined by a bal
28、anced ballot of materially interested parties who indicate interest in reviewing the proposed standard. Final approval of the IEEE standards document is given by the IEEE Standards Association (IEEE-SA) Standards Board. 3) IEC/IEEE Publications have the form of recommendations for international use
29、and are accepted by IEC National Committees/IEEE Societies in that sense. While all reasonable efforts are made to ensure that the technical content of IEC/IEEE Publications is accurate, IEC or IEEE cannot be held responsible for the way in which they are used or for any misinterpretation by any end
30、 user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications (including IEC/IEEE Publications) transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC/IEEE Publication and the corr
31、esponding national or regional publication shall be clearly indicated in the latter. 5) IEC and IEEE do not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC and IEEE are not respo
32、nsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or IEEE or their directors, employees, servants or agents including individual experts and members of technic
33、al committees and IEC National Committees, or volunteers of IEEE Societies and the Standards Coordinating Committees of the IEEE Standards Association (IEEE-SA) Standards Board, for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for cost
34、s (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC/IEEE Publication or any other IEC or IEEE Publications. 8) Attention is drawn to the normative references cited in this publication. Use of the referenced publications is indispensable for the co
35、rrect application of this publication. 9) Attention is drawn to the possibility that implementation of this IEC/IEEE Publication may require use of material covered by patent rights. By publication of this standard, no position is taken with respect to the existence or validity of any patent rights
36、in connection therewith. IEC or IEEE shall not be held responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patent Claims or determining whether any licensing terms or conditions provided in connection w
37、ith submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibilit
38、y. 4 62582-2 g148 IEC/IEEE:2011 International Standard IEC/IEEE 62582-2 has been prepared by subcommittee 45A: Instrumentation and control of nuclear facilities, of IEC technical committee 45: Nuclear instrumentation, in cooperation with the Nuclear Power Engineering Committee of the Power Fiis the
39、corresponding force value at displacement di.IM shall be determined by using the values F1 = 1 N and F2 = 4 N, see Figure 2. 1098765432100 0,1 0,2 0,3 0,4 0,5 0,6 F2 F1d2 d1Displacement (mm) Load (N)IEC 1962/11 Figure 2 Calculation of indenter modulus 6.10 Reporting The measurement report shall as a
40、 minimum include the following items a) Identification of the equipment measured, including the material formulation. For selection of samples from the field or measurements in the field this shall include plant and location relative to heat and radiation sources (6.2). b) Pre-history of the equipme
41、nt. This may include g120 indenter measurements on samples of new (un-aged) equipment: storage and time interval between production of the equipment sampled and start of the measurement (6.1); g120 indenter measurements on artificially aged samples: ageing conditions of the samples (6.2); g120 inden
42、ter measurements on naturally aged samples (e.g. field measurements): history of environmental conditions to which the sample has been subjected (6.2). c) Place and date of the measurement (laboratory, on-site). d) For laboratory measurement of samples subjected to artificial thermal ageing: time in
43、terval between removing the sample from the heat chamber until start of measurement (6.3). e) Ambient and surface temperature at the time of measurement (6.3). f) Other local conditions and situations encountered during measurement that may influence the results. g) Measurement instrumentation, incl
44、uding software version (6.4). h) Calibration procedure (6.5). i) Measurement points (6.6). j) Probe velocity (6.7). k) Maximum force (6.7). 62582-2 g148 IEC/IEEE:2011 13 l) Mounting of the sample and problems in clamping (6.8). m) For measurements in the field: observations on the condition of the e
45、quipment before and after indenter measurements (6.2). n) Mean value and standard deviation of indenter modulus ( after deleting the highest and lowest value), in Nmm1together with information on the force interval for which it has been determined (normally 1 N to 4 N) (6.6 and 6.9). NOTE If the ind
46、enter measurements are made at a temperature above 25 C, it is recommended that the value referenced to 20 C is also reported, calculated according to Annex A. o) Diagram showing a typical force versus displacement curve. p) Any other information of importance in interpretation of the measurement re
47、sults in relation to the purposes of the measurements. An example of a measurement report is given in Annex B. 14 62582-2 g148 IEC/IEEE:2011 Annex A (informative)Examples illustrating factors affecting the variation of the indenter modulus value A.1 Example of influence of variability in equipment d
48、imensions and construction Figure A.1 illustrates the variations due to variability in equipment dimensions and construction, showing sets of data from indenter measurements at eight points on the jacket of a 7 core cable with jacket material CSPE and insulator material EPDM. The mean values and sta
49、ndard deviations of the indenter modulus measured were 15,57 Nmm1and 0,58 Nmm1for the unaged cable jacket, 23,21 Nmm1and 1,06 Nmm1for the thermally aged cable jacket. 9 8 7 6 6 5 4 3 2 1 0 0 0,1 0,2 0,3 0,4 0,5 0,6 0,7 Load (N)Displacement (mm) Unaged 9 8 7 6 5 4 3 2 1 0 0 0,1 0,2 0,3 0,4 0,5 0,6 0,7 Load (N)Displacement (mm) Thermally aged 1 008 h at 120 C IEC 1964/11 IEC 1963/11 Figure A.1 Example of local variation of indenter modulus due to variatio
