1、Designation: D2792 17Standard Practice forSolvent and Fuel Resistance of Traffic Paint1This standard is issued under the fixed designation D2792; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number i
2、n parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice describes a laboratory procedure for de-termining the resistance of a dried film of traffic paint to theaction of a specified hyd
3、rocarbon solvent or gasoline fuel testfluid.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility o
4、f the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Dec
5、ision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D471 Test Method for Rubber PropertyEffect of Liquids2.2 Federal Standard:TT-S-7
6、35 Standard Test Fluids for Hydrocarbons33. Summary of Test Method3.1 The test paint is applied to a specified, properlyprepared, tin panel. After aging, the coated panel is immersedin the hydrocarbon test fluid for a specified period of time at aspecified temperature. The paint is examined for blis
7、tering,wrinkling, and loss of adhesion immediately upon removal andfor complete hardness after a specified recovery time.4. Significance and Use4.1 Traffic paints must have good resistance to motor oil andfuel drippings on the highway. This test method describes theprocedure necessary to evaluate th
8、e resistance of traffic paint toreference test fluids in order to simulate this type of action.5. Apparatus5.1 Tin PanelPanels shall be cut from bright tin plateweighing not more than 25 g and not less than 19 g/dm2(0.51to 0.39 lb/ft2). The panel should be about 75 by 130 mm (3 by5 in.).5.2 Film App
9、licator, which will producea3or6-mil (76 or142-m) (0.003 or 0.006-in.) wet film thickness.6. Reagents and Materials6.1 Test LiquidThe testing liquid shall be specified by thepurchaser and shall be selected from the following, dependenton the paint tested:6.1.1 Type I of Federal Specification TT-S-73
10、5 which is thesame as ASTM Reference Fuel A (Test Method D471).6.1.2 Type III of Federal Specification TT-S-735 which isthe same as ASTM Reference Fuel B (Test Method D471).7. Procedure7.1 Clean the tin panels thoroughly with a suitable solvent,and buff lightly with fine steel wool. Prepare at least
11、 3 panelsfor each paint to be tested.7.2 Examine the test paint, remove any skins that arepresent, stir with a paddle to loosen any settled pigment, andmix thoroughly.7.3 Draw down the material on the panels using a filmapplicator that will produce a 76 or 142-m (3 or 6-mil) wetfilm as specified by
12、the purchaser.7.4 Air dry the coating for the time specified by thepurchaser (usually 90 h) and then immerse the panels to halftheir length in the test liquid contained in a covered glassbeaker at the temperature specified by the purchaser (generally21 to 32C (70 to 90F). Use a separate beaker for e
13、ach painttested.1This practice is under the jurisdiction of ASTM Committee D01 on Paint andRelated Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.44 on Traffic Coatings.Current edition approved June 1, 2017. Published June 2017. Originallyapproved in 1969.
14、Last previous edition approved in 2015 as D2792 69 (2015).DOI: 10.1520/D2792-17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page
15、onthe ASTM website.3Available from DLA Document Services, Building 4/D, 700 Robbins Ave.,Philadelphia, PA 19111-5094, http:/quicksearch.dla.mil.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed i
16、n accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1Mon Apr 30 48 7.5 At the
17、end of the specified time (usually 4 to 18 h,depending on the type of paint) remove the panels and examineimmediately for blistering, wrinkling, and loss of adhesion.7.6 Allow the panels to dry at normal temperatures for thepurchaser-specified time (generally 24 h), and examine for filmdefects and s
18、oftening in comparison with the unimmersedportion of the panels.8. Report8.1 Report whether blistering, wrinkling, or loss of adhesionis evident immediately upon removal of panel from the testfluid as determined in 7.5.8.2 Report whether any softening of the film is evident afterthe panel has recove
19、red as determined in 7.6.9. Keywords9.1 solvent/fuel resistance test; traffic paintASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the
20、validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your
21、comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments h
22、ave not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multip
23、le copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 172Mon Apr 30 48
