1、Designation: C530 13 (Reapproved 2017)Standard Specification forStructural Clay Nonloadbearing Screen Tile1This standard is issued under the fixed designation C530; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last r
2、evision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers unglazed, structural clay, non-loadbearing screen tile.1.2 The property requirements of this speci
3、fication apply atthe time of purchase. The use of results from testing of tileextracted from masonry structures for determining confor-mance or nonconformance to the property requirements (Sec-tion 5) of this specification is beyond the scope of this standard.1.3 Tile covered by this specification a
4、re manufactured fromclay, shale, or similar naturally occurring substances andsubjected to a heat treatment at elevated temperatures (firing).The heat treatment must develop sufficient fired bond betweenthe particulate constituents to provide the strength and dura-bility requirements of this specifi
5、cation. (See firing and firedbond in Terminology C1232).1.4 The text of this specification references notes andfootnotes which provide explanatory material. These notes andfootnotes (excluding those in tables and figures) shall not beconsidered as requirements of the specification.1.5 The values sta
6、ted in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.6 This international standard was developed in accor-dance with internationally recognized principles
7、 on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2C67 Test Methods for Sampling and Tes
8、ting Brick andStructural Clay TileC1232 Terminology for Masonry3. Terminology3.1 DefinitionsFor definitions relating to structural claynonloadbearing screen tile, refer to Terminology C1232.4. Classification4.1 Three grades of screen tile, based on relative durability,are covered as follows:NOTE 1Sc
9、reen walls present many more exposed surfaces than otherbrick or tile walls, the question of durability and selection of grade may bemore critical in the screen walls. For this reason, these requirements aremore conservative than for brick.4.1.1 Grade SEScreen tile exhibiting a uniformly highresista
10、nce to disintegration by weathering or by freezing orthawing in the presence of moisture.4.1.2 Grade MEScreen tile exhibiting a moderate andsomewhat nonuniform resistance to weathering. Grade ME tileexhibit good durability in areas of mild to moderate exposurebut may not be adequate for severe expos
11、ures.4.1.3 Grade NEScreen tile for interior use (no exposure torain or freezing).4.1.4 When the grade is not specified, the requirements forGrade ME shall govern.4.1.5 Grade SE tile may be accepted in lieu of Grades MEor NE. Grade ME tile may be accepted in lieu of Grade NE.4.2 Two types of screen t
12、ile, based on dimensionaltolerances, are covered as follows:4.2.1 Type STXScreen tile having a high degree of me-chanical perfection and minimum size variation.4.2.2 Type STAScreen tile exhibiting characteristic archi-tectural effects resulting from a larger degree of size variationthan obtainable w
13、ith Type STX.4.2.3 When type is not specified, the requirements for TypeSTA shall govern.5. Physical Properties5.1 DurabilityScreen tile shall meet the properties pre-scribed in Table 1 for resistance to absorption.1This specification is under the jurisdiction of ASTM Committee C15 onManufactured Ma
14、sonry Units and is the direct responsibility of SubcommitteeC15.02 on Brick and Structural Clay Tile.Current edition approved Dec. 1, 2017. Published December 2013. Originallyapproved in 1963. Last previous edition approved in 2013 as C530 13. DOI:10.1520/C0530-13R17.2For referenced ASTM standards,
15、visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428
16、-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technic
17、al Barriers to Trade (TBT) Committee.16. Dimensions and Permissible Variations6.1 The dimensions of screen tile units shall be specified bythe purchaser.NOTE 2Since screen tile are available in numerous sizes and shapes,the purchaser must specify these items. All sizes and shapes are notnecessarily
18、available in all parts of the United States. Therefore, thespecifier should ascertain local availability before specifying a particularunit size or pattern.6.2 No screen tile shall have greater dimensional variationthan that permitted in Table 2.7. Finish and Appearance7.1 All tile shall be reasonab
19、ly free from laminations andfrom defects that impair the placement, strength, or perma-nence of the construction.7.2 Tile surfaces shall be smooth, scored, combed, orroughened as specified by the purchaser.7.3 Color, texture, and pattern shall be specified by thepurchaser. The texture and color rang
20、e that will be visible in thefinished wall shall conform to an approved sample of at leastfour representative units.NOTE 3Tile colors vary with clay type and degree of burning. Colordoes not indicate tile classification unless it has been related to absorptionand strength by tests.Because a multitud
21、e of individual unit patterns and wall patterns areavailable, screen-wall strength in every direction may not be related to thecompressive strength of individual units. Designers are cautioned toinvestigate each wall design thoroughly and to provide sufficient expan-sion and pressure-relieving joint
22、s to eliminate induced forces that mightcreate critical stresses in screen-wall units.8. Optional Requirements8.1 If the purchaser desires closer dimensional tolerances,restrictions on chippage or roughness, or other requirementsnot specifically contained in this specification, he must so statein a
23、supplemental specification.9. Sampling and Testing9.1 Sample and test tile in accordance with Test MethodsC67.10. Keywords10.1 clay; masonry; nonloadbearing tile; physical proper-ties; screen tile; shale; tileASTM International takes no position respecting the validity of any patent rights asserted
24、in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the
25、responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive ca
26、reful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM Internatio
27、nal, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the
28、 ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 1 Physical PropertiesGradeMaximum Water Absorption by 1-h Boiling,percentAverage of FiveTestsIndividualS
29、E 10 12ME 14 16NE 20 24TABLE 2 Dimensions and Permissible VariationsSpecified Dimension,in. (mm)Maximum Permissible Variations fromSpecified Dimensions, Plus or Minus,in. (mm)TypeSTXTypeSTAUp to 4, incl. (101.6)332 (2.38)432 (3.18)Over 4 to 6 (101.6 to 152.4)432 (3.18)632 (4.76)Over 6 to 8 (152.4 to 203.2)532 (3.96)832 (6.35)Over 8 to 12 (203.2 to 304.8)732 (5.56)1032 (7.94)Over 12 (304.8)932 (7.14)1232 (9.52)C530 13 (2017)2
