1、Designation: F1331 91 (Reapproved 2017) An American National StandardStandard Practice forInstallation Procedures of Vinyl Deck Coverings on PortablePlates in Electrical and Electronic Spaces1This standard is issued under the fixed designation F1331; the number immediately following the designation
2、indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers the acceptable me
3、thod for installinginsulated deck covering on portable deck plates.1.2 This deck covering shall be installed, in way of theelectrical and electronic spaces, for marine use.1.3 The values stated in SI (metric) units are to be regardedas the standard. The values in parentheses are for informationonly.
4、1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.1.5 This intern
5、ational standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Co
6、mmittee.2. Referenced Documents2.1 ASTM Standards:2D1338 Practice for Working Life of Liquid or Paste Adhe-sives by Consistency and Bond StrengthD2393 Test Method for Viscosity of Epoxy Resins andRelated Components (Withdrawn 1992)3D4389 Specification for Finished Glass Fabrics Woven FromRovingsF150
7、 Test Method for Electrical Resistance of Conductiveand Static Dissipative Resilient Flooring2.2 Other Documents:Steel Structural Painting Council SP-1143. Requirements3.1 Operations AreaTypical areas for application of theelectric insulating deck covering are:3.1.1 The operating areas in front and
8、rear of power andlighting switchboards, interior-communication switchboards,test switchboards, fire-control switchboards, and shipboardannouncing-systems amplifiers and control panels.3.1.2 The area around electronic equipment which may becontacted by personnel in servicing or tuning energized equip
9、-ment.3.1.3 Vinyl sheets should be confined to the minimum deckareas (generally 0.9 m (3 ft) wide) surrounding the apparatusnecessary to prevent electric shock, and should, unless other-wise specified, be cemented to the deck in lieu of otherspecified deck coverings.3.2 Installation Vinyl Sheets:3.2
10、.1 Installation of deck covering shall be in accordancewith Figs. 1-7, using vinyl sheet and fiberglass binding strips(see Fig. 1 and Fig. 5).3.2.2 Vinyl sheets and fiberglass sheets shall be united at theedges in a rabbet joint as shown (see Fig. 7), and such that thefiberglass overlaps at all join
11、ts. All rabbeted surfaces shall besmooth and corners sharp and square, such that at installationthe overlapping areas fit firmly and flush. Vinyl shall meetrequirements and tests provided in Test Method F150.3.3 Adhesive:3.3.1 Vinyl sheets shall be secured to each portable platewith adhesive. Adhesi
12、ve should not extend beyond edges ofvinyl sheet.3.3.2 Silicone compound, with 1 % liquid catalyst, shouldbe applied between lapping areas in accordance with PracticeD1338.3.4 FiberglassGlass fiber base, epoxy resin sheets fur-nished under this specification (Fig. 1 and Fig. 5), shall be aproduct con
13、sisting of plies or layers of cloth or nonwoven1This practice is under the jurisdiction of ASTM Committee F25 on Ships andMarine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved May 1, 2017. Published May 2017. Originallyappr
14、oved in 1991. Last previous edition approved in 2012 as F1331 91 (2012).DOI: 10.1520/F1331-91R17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Docum
15、ent Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from Society for Protective Coatings (SSPC), 800 Trumbull Dr.,Pittsburgh, PA 15205, http:/www.sspc.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700,
16、West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World
17、 Trade Organization Technical Barriers to Trade (TBT) Committee.1parallel aligned fibers bonded with an epoxy resin compound,in accordance with Specification D4389.3.5 Fastening with Nylon ScrewsFiberglass binding stripsshall be secured to the deck with nylon screws. A 76-mm(3-in.) wide strip over j
18、oints between portable plates shall befastened with a double row of screws. A 38-mm (112-in.) widestrip or shape to suit at deck edges shall be fastened with asingle row of screws, spacing between screws not to exceed127 mm (5 in.) center-to-center and located to clear deck platescrews. (See Fig. 7.
19、)3.6 Exposed Areas Treated with Epoxy:3.6.1 Before the epoxy is applied, the surface to be coveredshould be (a) cleaned with a solvent, and (b) further treated inaccordance with Steel Structural Painting Council SP-11.3.6.2 Epoxy resin shall be applied to the exposed vertical lipof deck edges on sta
20、nchions, to approximately 305 mm (12 in.)above deck, after all other deck covering work has beencompleted. Application of epoxy shall be by brush to approxi-mately 1.5-mm (116-in.) thickness, and in accordance with TestMethod D2393. (For location of epoxy to be applied, see Fig.3 and Fig. 4.)4. Keyw
21、ords4.1 deck covering; electrical space; electronic space; insu-lated deck covering; marine technology; portable deck plate;ship; vinyl deck coveringFIG. 1 Typical Deck Covering Plan ViewFIG. 2 Section “D-D” (See Fig. 1)FIG. 3 Expanded View of Deck Covering at Stanchion (TYP)NOTE 125.4 mm=1in.FIG. 4
22、 Section “A-A” (See Fig. 3)FIG. 5 Expanded View of One Portable Plate (TYP)F1331 91 (2017)2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination
23、 of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdraw
24、n. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your co
25、mments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single o
26、r multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 125.4 mm=1in.FIG. 6 Section “B-B” (See Fig. 5)NOTE 125.4 mm=1in.FIG. 7 Section “C-C” (See Fig. 5)F1331 91 (2017)3
