1、IEEE Standard for Performance Characteristics and Dimensions for Power Transformer and Reactor Bushings IEEE Std C57.19.01-2017 (Revision of IEEE Std C57.19.01-2000) IEEE Power and Energy Society Sponsored by the Transformers Committee IEEE 3 Park Avenue New York, NY 10016-5997 USAIEEE Std C57.19.01
2、-2017 (Revision of IEEE Std C57.19.01-2000) IEEE Standard for Performance Characteristics and Dimensions for Power Transformer and Reactor Bushings Sponsor Transformers Committee of the IEEE Power and Energy Society Approved 06 December 2017 IEEE-SA Standards BoardAbstract: Electrical, dimensional,
3、and related requirements for power transformer and reactor bushings that have basic impulse insulation levels (BILs) of 150 kV and above are covered. Specific values for dimensional and related requirements that are to be interpreted, measured, or tested, in accordance with IEEE Std C57.19.00, are p
4、rovided. Keywords: basic impulse insulation levels, BILs, cantilever test, capacitance, creepage distance, flashover, IEEE Std C57.19.01, line-to-ground voltage, nominal system voltage, power factor, power reactor bushings, power transformer bushings The Institute of Electrical and Electronics Engin
5、eers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2018 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 12 July 2018. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent fitness for a particular purpos
6、e; non-infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly vo
7、luntary. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is sub
8、ject to change brought about through developments in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE unde
9、rtaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competent professio
10、nal in determining the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
11、 INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETH
12、ER SUCH DAMAGE W AS FORESEEABLE.4 Copyright 2018 IEEE. All rights reserved. Translations The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the appr
13、oved IEEE standard. Official statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relie
14、d upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position of IEEE. Comments
15、 on standards Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should b
16、e in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important that any responses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE and
17、 the members of its societies and Standards Coordinating Committees are not able to provide an instant response to comments or questions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would l
18、ike to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documents
19、 should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. I
20、EEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws. They are ma
21、de available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making these documents available for
22、 use and adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents.5 Copyright 2018 IEEE. All rights reserved. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of a
23、ny individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portion
24、s of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Updating of IEEE Standards documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be
25、amended from time to time through the issuance of amendments, corrigenda, or errata. A current IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at least ev
26、ery ten years. When a document is more than ten years old and has not undergone a revision process, it is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest ed
27、ition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE Xplore at http:/ ieeexplore .ieee .or g/ or contact IEEE at the address listed previously. For m
28、ore information about the IEEE-SA or IEEEs standards development process, visit the IEEE-SA Website at http:/ standards .ieee .or g. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/ standards .ieee .org/ findstds/ errata/ index .html.
29、Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existe
30、nce or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE- SA Website at http:/ standards .ieee .or g/ about/ sasb/ patcom/ patents .html. Lette
31、rs of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses
32、. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any
33、licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringeme
34、nt of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association.6 Copyright 2018 IEEE. All rights reserved. Participants At the time this IEEE standard was completed, the Bushing-Performance Characteristics Working Group had the follow
35、ing membership: Shibao Zhang, Chair David Wallach, Secretary Barry Beaster Jeffrey Benach Scott Digby Keith Ellis Eric Eurvard James Fairris Anthony Franchitti David Geibel John Graham Shamaun Hakim Michael Hardin Eric Humphrey Wayne Johnson Arvin Joshi Marek Kornowski Weijun Li Kerry Livingston Mar
36、io Locarno Terence Martin Robert Middleton Sebastien Riopel Mark Rivers Eric Schleismann Devki Sharma Fabian Stacy Kevin Sullivan Troy Tanaka Y ves V ermette Eric Weatherbee Kwasi Y ehoah Peter Zhao The following members of the balloting committee voted on this standard. Balloters may have voted for
37、 approval, disapproval, or abstention. Donald A yers Roy A yers Peter Balma Thomas Barnes Barry Beaster Enrique Betancourt Wallace Binder Thomas Blackburn W. Boettger Jeffrey Brogdon Demetrio Bucaneg Jr. Eldridge Byron Paul Cardinal Willaim Darovny Scott Digby Dieter Dohnal Gary Donner Jorge Fernand
38、ez Daher Sergio Flores Joseph Foldi Bruce Forsyth Anthony Franchitti Fredric Friend George Frimpong David Geibel John Graham Randall Groves John Harley Werner Hoelzl Gary Hoffman Jill Holmes Philip Hopkinson Daniel Huenger Eric Humphrey Richard Jackson John John Peter Kelly Boris Kogan Axel Kraemer
39、Jim Kulchisky John Lackey Chung-Yiu Lam Benjamin Lanz William Larzelere Mario Locarno J. Dennis Marlow Lee Matthews John McClelland Mark McNally Andrew McNulty Joseph Melanson Daniel Mulkey Jerry Murphy Ryan Musgrove Ali Naderian Jahromi K. R. M. Nair Kris K. Neild Arthur Neubauer Michael Newman T.
40、W . Olsen Lorraine Padden Bansi Patel Dhiru Patel Poorvi Patel Brian Penny Christopher Petrola Donald Platts Alvaro Portillo Ulf Radbrandt Timothy Charles Raymond Jean-Christophe Riboud Johannes Rickmann Sebastien Riopel Thomas Rozek Daniel Sauer Roderick Sauls Bartien Sayogo Eric Schleismann Ewald
41、Schweiger Devki Sharma Hemchandra Shertukde Hyeong Sim Jerry Smith Steve Snyder Brian Sparling Philip Spotts Ronald Stahara Gary Stoedter Troy Alan Tanaka David Tepen Juan Thierry Jason V arnell Roger V erdolin John V ergis Y ves V ermette David Wallach Eric Weatherbee Peter Werelius Baitun Y ang Jennifer Y u Jian Y u Xi Zhu
