1、BSI Standards Publication BS ISO 603-17:2014 Bonded abrasive products Dimensions Part 17: Spindle mounted wheels (ISO type 52)BS ISO 603-17:2014 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 603-17:2014. The UK participation in its preparation was entrusted
2、 to Technical Committee MTE/13, Grinding wheels, abrasive tools, paper and cloths, and powders. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are respon
3、sible for its correct application. The British Standards Institution 2014. Published by BSI Standards Limited 2014 ISBN 978 0 580 75117 2 ICS 25.100.70 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Sta
4、ndards Policy and Strategy Committee on 31 July 2014. Amendments issued since publication Date Text affectedBS ISO 603-17:2014 ISO 2014 Bonded abrasive products Dimensions Part 17: Spindle mounted wheels (ISO type 52) Produits abrasifs agglomrs Dimensions Partie 17: Meules sur tige (ISO type 52) INT
5、ERNATIONAL STANDARD ISO 603-17 First edition 2014-07-15 Reference number ISO 603-17:2014(E)BS ISO 603-17:2014ISO 603-17:2014(E)ii ISO 2014 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utili
6、zed otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyrigh
7、t office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 603-17:2014ISO 603-17:2014(E) ISO 2014 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Normative references 1 3 Shapes and di
8、mensions . 1 3.1 Wheel plain, Shape WPL . 1 3.2 Wheel concave end, Shape WCC . 4 3.3 Wheel round end, Shape WRE . 4 3.4 Wheel conical end, Shape WCE . 5 3.5 Wheel truncated cone end, Shape WTC . 6 3.6 Wheel conical round end, Shape WCR 6 3.7 Conical double taper, Shape CDT . 7 3.8 Conical round end,
9、 Shape CRE . 8 3.9 Conical truncated end, Shape CTE 9 3.10 Wheel ogival end, Shape WOE . 9 3.11 Spherical, Shape SPH 10 3.12 Conical inverse cup, Shape CIC .11 3.13 Profiled periphery tapered, Shape PPT 12 3.14 Conical inverse flat end, Shape CIF .13 3.15 Conical inverse round end, Shape CIR .14 3.1
10、6 Profiled periphery curved, Shape PPC .15 3.17 Profiled periphery pointed, Shape PPP.15 3.18 Conical inverse dish, Shape CID . 16 3.19 Mushroom, Shape MSH .17 4 Designation .18 5 Specifications 18 5.1 Material 18 5.2 Marking 18BS ISO 603-17:2014ISO 603-17:2014(E) Foreword ISO (the International Org
11、anization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been establi
12、shed has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardizatio
13、n. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with
14、the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any pa
15、tent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. F
16、or an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible fo
17、r this document is ISO/TC 29, Small tools, Subcommittee SC 5, Grinding wheels and abrasives. ISO 603 consists of the following parts, under the general title Bonded abrasive products Dimensions: Part 1: Grinding wheels for external cylindrical grinding between centres Part 2: Grinding wheels for cen
18、treless external cylindrical grinding Part 3: Grinding wheels for internal cylindrical grinding Part 4: Grinding wheels for surface grinding/peripheral grinding Part 5: Grinding wheels for surface grinding/face grinding Part 6: Grinding wheels for tool and tool room grinding Part 7: Grinding wheels
19、for manually guided grinding Part 8: Grinding wheels for deburring and fettling/snagging Part 9: Grinding wheels for high-pressure grinding Part 10: Stones for honing and superfinishings Part 11: Hand finishing sticks Part 12: Grinding wheels for deburring and fettling on a straight grinder Part 13:
20、 Grinding wheels for deburring and fettling on a vertical grinder Part 14: Grinding wheels for deburring and fettling/snagging on an angle grinder Part 15: Grinding wheels for cutting-off on stationary or mobile cutting-off machines Part 16: Grinding wheels for cutting-off on hand-held power toolsiv
21、 ISO 2014 All rights reservedBS ISO 603-17:2014ISO 603-17:2014(E) Part 17: Spindle mounted wheels (ISO type 52) Part 18: Grinding wheels for flat glass edge grinding machines ISO 2014 All rights reserved vBS ISO 603-17:2014BS ISO 603-17:2014Bonded abrasive products Dimensions Part 17: Spindle mounte
22、d wheels (ISO type 52) 1 Scope This part of ISO 603 specifies the current shapes, nominal dimensions and limit deviations, in millimetres, of Type 52: Spindle mounted wheels. These bonded abrasive products are intended to be used for hand-held grinding and manually guided or on hand-held power tools
23、 guided by hand. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (in
24、cluding any amendments) applies. ISO 525, Bonded abrasive products General requirements 3 Shapes and dimensions NOTE 1 In all tables below, the “Designation” given in the first column is generated according to the following principle: Shape (= three letter code), D (mm), T (mm), and S d(mm). For exa
25、mple, the designation for a spindle mounted wheel, shape WPL with D = 10 mm, T = 13 mm, and S d= 6 mm the designation is “WPL 10 13 06”. As an exception, this rule can only be applied equivalently to 3.11, Table 11, because dimension T does not exist for the spherical shape. NOTE 2 In all tables bel
26、ow, the former code is given in the second column for information only. 3.1 Wheel plain, Shape WPL See Figure 1 and Table 1. INTERNATIONAL ST ANDARD ISO 603-17:2014(E) ISO 2014 All rights reserved 1BS ISO 603-17:2014ISO 603-17:2014(E) Dimensions in millimetres Key 1 collet a L 3 10. b S d= 3 and L 2
27、= 30 or S d= 6 and L 2= 40 or S d= 8 and L 2= 40. Figure 1 Wheel plain, Shape WPL Table 1 Wheel plain, Shape WPL, S d= 3 mm and L 2= 30 mm or S d= 6 mm and L 2= 40 mm or S d= 8 mm and L 2= 40 mm Dimensions in millimetres Designation Former code D T WPL 03 06 03 W144 3 6 WPL 03 10 03 W145 10 WPL 03 1
28、3 03 W146 13 WPL 05 06 03 W152 5 6 WPL 05 10 03 W153 10 WPL 05 13 03 W154 13 WPL 06 06 03 W160 6 6 WPL 06 10 03 WPL 06 10 06 W162 10 WPL 06 13 03 WPL 06 13 06 W163 13 WPL 06 20 03 W164 20 WPL 08 10 03 WPL 08 10 06 W169 8 10 WPL 08 13 03 W170 13 WPL 08 20 03 W171 20 WPL 10 10 03 WPL 10 10 06 W175 10
29、10 WPL 10 13 03 WPL 10 13 06 W176 13 WPL 10 20 03 WPL 10 20 06 W177 20 WPL 10 25 03 WPL 10 25 06 W178 25 WPL 10 32 06 W179 322 ISO 2014 All rights reservedBS ISO 603-17:2014ISO 603-17:2014(E) Designation Former code D T WPL 13 03 03 WPL 13 03 06 W182 13 3 WPL 13 06 03 WPL 13 06 06 W183 6 WPL 13 13 0
30、3 WPL 13 13 06 W185 13 WPL 13 20 03 WPL 13 20 06 W186 20 WPL 13 25 03 WPL 13 25 06 W187 25 WPL 13 40 06 W188 40 WPL 16 20 03 WPL 16 20 06 W195 16 20 WPL 16 25 03 WPL 16 25 06 W196 25 WPL 16 50 06 W197 50 WPL 20 06 03 WPL 20 06 06 W201 20 6 WPL 20 10 03 WPL 20 10 06 W202 10 WPL 20 20 03 WPL 20 20 06
31、W204 20 WPL 20 25 06 W205 25 WPL 20 32 06 W206 32 WPL 20 38 06 W207 38 WPL 20 50 06 W208 50 WPL 25 03 03 WPL 25 03 06 W215 25 3 WPL 25 06 03 WPL 25 06 06 W216 6 WPL 25 10 06 W217 10 WPL 25 13 06 W218 13 WPL 25 20 06 W219 20 WPL 25 25 06 W220 25 WPL 25 32 06 WPL 25 32 08 W221 32 WPL 25 50 06 WPL 25 5
32、0 08 W222 50 WPL 32 06 06 W225 32 6 WPL 32 10 06 W226 10 WPL 32 20 06 W228 20 WPL 32 32 06 WPL 32 32 08 W230 32 WPL 32 50 06 W232 50 WPL 38 06 06 W235 38 6 WPL 38 13 06 W236 13 WPL 38 38 06 WPL 38 38 08 W238 38Table 1 (continued) ISO 2014 All rights reserved 3BS ISO 603-17:2014ISO 603-17:2014(E) Des
33、ignation Former code D T WPL 40 20 06 WPL 40 20 08 W237 40 20 WPL 50 25 06 WPL 50 25 08 W242 50 25 3.2 Wheel concave end, Shape WCC See Figure 2 and Table 2. Dimensions in millimetres Key 1 collet a L 3 10. b S d= 3 and L 2= 30 or S d= 6 and L 2= 40. c R is specified by the manufacturer. Figure 2 Wh
34、eel concave end, Shape WCC Table 2 Wheel concave end, Shape WCC, S d= 3 mm and L 2= 30 mm or S d= 6 mm and L 2= 40 mm Dimensions in millimetres Designation Former code D T WCC 06 13 03 B135 6 13 WCC 10 13 06 B132 10 13 WCC 10 10 03 B133 10 WCC 10 13 03 B132 13 WCC 13 13 03 WCC 13 13 06 B131 13 13 WC
35、C 20 30 06 A39 20 30 WCC 25 25 06 A38 25 25 3.3 Wheel round end, Shape WRE See Figure 3 and Table 3.Table 1 (continued) 4 ISO 2014 All rights reservedBS ISO 603-17:2014ISO 603-17:2014(E) Key 1 collet a L 3 10. b S d= 6 and L 2= 40. Figure 3 Wheel round end, Shape WRE Table 3 Wheel round end, Shape W
36、RE, S d= 6 mm and L 2= 40 mm Dimensions in millimetres Designation Former code D T WRE 06 20 06 A24 6 20 WRE 25 25 06 A21 25 25 3.4 Wheel conical end, Shape WCE See Figure 4 and Table 4. Dimensions in millimetres Key 1 collet a For D 20 mm is = 60. For D 20 mm is = 90. b L 3 10. c S d= 3 and L 2= 40
37、 or S d= 6 and L 2= 40. d is specified by the manufacturer. Figure 4 Wheel conical end, Shape WCE ISO 2014 All rights reserved 5BS ISO 603-17:2014ISO 603-17:2014(E) Table 4 Wheel conical end, Shape WCE, S d= 3 mm and L 2= 30 mm or S d= 6 mm and L 2= 40 mm Dimensions in millimetres Designation Former
38、 code D T WCE 06 10 03 B53 6 10 WCE 06 27 06 A15 27 WCE 20 22 06 A14 20 22 WCE 20 63 06 A1 63 WCE 28 28 06 A13 28 28 3.5 Wheel truncated cone end, Shape WTC See Figure 5 and Table 5. Dimensions in millimetres Key 1 collet a For D 20 mm is = 60. For D 20 mm is = 90. b L 3 10. c S d= 3 and L 2= 30 or
39、S d= 6 and L 2= 40. Figure 5 Wheel truncated cone end, Shape WTC Table 5 Wheel truncated cone end, Shape WTC, S d= 3 mm and L 2= 30 mm or S d= 6 mm and L 2= 40 mm Dimensions in millimetres Designation Former code D T WTC 06 10 03 B53 6 10 WTC 06 27 06 A15 27 WTC 20 22 06 A14 20 22 WTC 20 63 06 A1 63
40、 WTC 28 28 06 A13 28 28 3.6 Wheel conical round end, Shape WCR See Figure 6 and Table 6.6 ISO 2014 All rights reservedBS ISO 603-17:2014ISO 603-17:2014(E) Dimensions in millimetres Key 1 collet a L 3 10. b S d= 3 and L 2= 30 or S d= 6 and L 2= 40. c R is specified by the manufacturer. d T 1is specif
41、ied by the manufacturer. e T 2is specified by the manufacturer. Figure 6 Wheel conical round end, Shape WCR Table 6 Wheel conical round end, Shape WCR, S d= 3 mm and L 2= 30 mm or S d= 6 mm and L 2= 40 mm Dimensions in millimetres Designation Former code D T WCR 16 16 03 WCR 16 16 06 B41 16 16 WCR 2
42、0 30 06 A5 20 30 WCR 32 32 06 A4 32 32 3.7 Conical double taper, Shape CDT See Figure 7 and Table 7. ISO 2014 All rights reserved 7BS ISO 603-17:2014ISO 603-17:2014(E) Dimensions in millimetres Key 1 collet a L 3 10. b S d= 3 and L 2= 30 or S d= 6 and L 2= 40. c D is specified by the manufacturer. d
43、 T 2is specified by the manufacturer. Figure 7 Conical double taper, Shape CDT Table 7 Conical double taper, Shape CDT, S d= 3 mm and L 2= 30 mm or S d= 6 mm and L 2= 40 mm Dimensions in millimetres Designation Former code D T CDT 11 20 03 CDT 11 20 06 B51 11 20 3.8 Conical round end, Shape CRE See
44、Figure 8 and Table 8. Dimensions in millimetres Key 1 collet a R is specified by the manufacturer. b L 3 10. c S d= 6 and L 2= 40. Figure 8 Conical round end, Shape CRE8 ISO 2014 All rights reservedBS ISO 603-17:2014ISO 603-17:2014(E) Table 8 Conical round end, Shape CRE, S d= 6 mm and L 2= 40 mm Di
45、mensions in millimetres Designation Former code D T CRE 16 45 06 A3mini 16 45 CRE 25 70 06 A3 25 70 3.9 Conical truncated end, Shape CTE See Figure 9 and Table 9. Dimensions in millimetres Key 1 collet a L 3 10. b S d= 3 and L 2= 30 or S d= 6 and L 2= 40. c is specified by the manufacturer. Figure 9
46、 Conical truncated end, Shape CTE Table 9 Conical truncated end, Shape CTE, S d= 3 mm and L 2= 30 mm or S d= 6 mm and L 2= 40 mm Dimensions in millimetres Designation Former code D T CTE 03 06 03 B96 3 6 CTE 03 10 03 B97 10 CTE 06 06 03 B92 6 6 CTE 13 16 03 CTE 13 16 06 B91 13 16 3.10 Wheel ogival e
47、nd, Shape WOE See Figure 10 and Table 10. ISO 2014 All rights reserved 9BS ISO 603-17:2014ISO 603-17:2014(E) Dimensions in millimetres Key 1 collet a R = 1 to 2,5 D. b L 3 10. c S d= 3 and L 2= 30 or S d= 6 and L 2= 40. Figure 10 Wheel ogival end, Shape WOE Table 10 Wheel ogival end, Shape WOE, S d=
48、 3 mm and L 2= 30 mm or S d= 6 mm and L 2= 40 mm Dimensions in millimetres Designation Former code D T WOE 06 08 03 B43 6 8 WOE 10 20 03 WOE 10 20 06 B52 10 20 WOE 13 20 03 WOE 13 20 06 B42 13 WOE 20 32 06 A12 20 32 WOE 22 50 06 A11 22 50 3.11 Spherical, Shape SPH See Figure 11 and Table 11.10 ISO 2
49、014 All rights reservedBS ISO 603-17:2014ISO 603-17:2014(E) Dimensions in millimetres Key 1 collet a L 3 10. b S d= 3 and L 2= 30 or S d= 6 and L 2= 40. Figure 11 Spherical, Shape SPH Table 11 Spindle mounted wheels spherical shape, Shape SPH, S d= 3 mm and L 2= 30 mm or S d= 6 mm and L 2= 40 mm Dimensions in millimetres Designation Former code D SPH 03 03 B124 3 SPH 05 03 B123 5 SPH 13 03 SPH 13 06 B1
