1、Reciprocating internal combustion engine driven alternating current generating sets Part 7: Technical declarations for specification and design BS ISO 85287:2017 BSI Standards Publication WB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06 ISO 2017 Reciprocating internal combustion engine drive
2、n alternating current generating sets Part 7: Technical declarations for specification and design Groupes lectrognes courant alternatif entrans par moteurs alternatifs combustion interne Partie 7: Dclarations techniques pour la spcification et la conception INTERNATIONAL STANDARD ISO 8528-7 Second e
3、dition 2017-07 Reference number ISO 8528-7:2017(E) National foreword This British Standard is the UK implementation of ISO 85287:2017. It supersedes BS 76987:1996 , which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MCE/14, RIC engines. A list of organiz
4、ations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017
5、 ISBN 978 0 580 85455 2 ICS 29.160.40; 27.020Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2017. Amendments/corrigenda issued since publicationDate Te
6、xt affected BRITISH STANDARD BS ISO 85287:2017 ISO 2017 Reciprocating internal combustion engine driven alternating current generating sets Part 7: Technical declarations for specification and design Groupes lectrognes courant alternatif entrans par moteurs alternatifs combustion interne Partie 7: D
7、clarations techniques pour la spcification et la conception INTERNATIONAL STANDARD ISO 8528-7 Second edition 2017-07 Reference number ISO 8528-7:2017(E) BS ISO 85287:2017 ISO 8528-7:2017(E)ii ISO 2017 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in Switzerland All rights rese
8、rved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either IS
9、O at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.org BS ISO 85287:2017 ISO 8528-7:2017(E)ii ISO 2017 All rights reserved
10、 COPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intran
11、et, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org
12、 www.iso.orgISO 8528-7:2017(E)Foreword iv 1 Scope . 1 2 Normative references 1 3 Terms and definitions . 2 4 Technical declarations 2 5 Other regulations and additional requirements . 6 Annex A (normative) Technical questionnaire General data 7 Annex A (normative) Technical questionnaire Specific da
13、ta 10 Annex B (normative) Generating set data 11 Bibliography .13 ISO 2017 All rights reserved iii Contents Page BS ISO 85287:2017 ISO 8528-7:2017(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work
14、 of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmen
15、tal, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the
16、 ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives). Attention is drawn to the po
17、ssibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list
18、 of patent declarations received (see www .iso .org/ patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions rel
19、ated to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html. This document was prepared by ISO/TC 70, Internal combustion engines. This s
20、econd edition cancels and replaces the first edition (ISO 8528-7:1994), which has been technically revised. A list of all parts in the ISO 8528 series can be found on the ISO websiteiv ISO 2017 All rights reserved BS ISO 85287:2017 ISO 8528-7:2017(E) Foreword ISO (the International Organization for
21、Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the r
22、ight to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedu
23、res used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial
24、rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights
25、 identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an ex
26、planation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .o
27、rg/ iso/ foreword .html. This document was prepared by ISO/TC 70, Internal combustion engines. This second edition cancels and replaces the first edition (ISO 8528-7:1994), which has been technically revised. A list of all parts in the ISO 8528 series can be found on the ISO websiteiv ISO 2017 All r
28、ights reserved INTERNATIONAL ST ANDARD ISO 8528-7:2017(E) Reciprocating internal combustion engine driven alternating current generating sets Part 7: Technical declarations for specification and design 1 Scope This document specifies the requirements and parameters for the specification and design o
29、f a reciprocating internal combustion (RIC) engine driven generating set, with reference to the definitions given in ISO 8528-1 to ISO 8528-6. It applies to alternating current (a.c.) generating sets driven by RIC engines for land and marine use, excluding generating sets used on aircraft or to prop
30、el land vehicles and locomotives. For some specific applications (for example, essential hospital supplies, high-rise buildings, etc.) supplementary requirements may be necessary. The provisions of this document are intended to be regarded as a basis. For other reciprocating-type prime movers (e.g.
31、sewage gas engines, steam engines), the provisions of this document are intended to be used as a basis. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the
32、 edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 8178-3, Reciprocating internal combustion engines Exhaust emission measurement Part 3: Definitions and methods of measurement of exhaust gas smoke under steady-state
33、conditions ISO 8528-1:2005, Reciprocating internal combustion engine driven alternating current generating sets Part 1: Application, ratings and performance ISO 8528-2:2005, Reciprocating internal combustion engine driven alternating current generating sets Part 2: Engines ISO 8528-3:2005, Reciproca
34、ting internal combustion engine driven alternating current generating sets Part 3: Alternating current generators for generating sets ISO 8528-4:2005, Reciprocating internal combustion engine driven alternating current generating sets Part 4: Controlgear and switchgear ISO 8528-5:2013, Reciprocating
35、 internal combustion engine driven alternating current generating sets Part 5: Generating sets ISO 8528-6:2005, Reciprocating internal combustion engine driven alternating current generating sets Part 6: Te s t methods IEC 60034-2-1, Rotating electrical machines Part 2-1: Standard methods for determ
36、ining losses and efficiency from tests (excluding machines for traction vehicles) IEC 60034-5, Rotating electrical machines Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) Classification ISO 2017 All rights reserved 1 BS ISO 85287:2017 ISO 8528
37、-7:2017(E) IEC 60034-6, Rotating electrical machines Part 6: Methods of cooling (IC code) IEC 60034 -7, Rotating electrical machines Part 7: Classification of types of construction, mounting arrangements and terminal box position (IM code) IEC 60364-4-41, Low-voltage electrical installations Part 4-
38、41: Protection for safety Protection against electric shock 3 Terms and definitions For the purposes of this document, the terms and definitions in ISO 8528-1 to ISO 8528-6 apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: a
39、vailable at h t t p :/ www .electropedia .org/ ISO Online browsing platform: available at h t t p s :/ www .iso .org/ obp 4 Technical declarations In order to achieve the appropriate layout of a power generation station, the customer/user shall give requirements and parameters to the generating set
40、manufacturer. Special items for the most important requirements and parameters are listed in Table 1, 4.1 to 4.19. If there are no specific declarations stated by the customer, then the declarations stated by the manufacturer should be taken as the basis for the requirements and parameters. The foll
41、owing distinction shall be made between the manufacturer and customer/user: Declarations which the customer or the user of the generating set are required to provide; Declarations which the manufacturer of the generating set are required to provide; Declarations to be agreed between the manufacturer
42、 and customer/user. These are indicated by symbol “X” in Table 1, columns “M” (manufacturer) and “C” (customer) of 4.1 to 4.19.2 ISO 2017 All rights reserved BS ISO 85287:2017 ISO 8528-7:2017(E) IEC 60034-6, Rotating electrical machines Part 6: Methods of cooling (IC code) IEC 60034 -7, Rotating ele
43、ctrical machines Part 7: Classification of types of construction, mounting arrangements and terminal box position (IM code) IEC 60364-4-41, Low-voltage electrical installations Part 4-41: Protection for safety Protection against electric shock 3 Terms and definitions For the purposes of this documen
44、t, the terms and definitions in ISO 8528-1 to ISO 8528-6 apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at h t t p :/ www .electropedia .org/ ISO Online browsing platform: available at h t t p s :/ www .iso .org
45、/ obp 4 Technical declarations In order to achieve the appropriate layout of a power generation station, the customer/user shall give requirements and parameters to the generating set manufacturer. Special items for the most important requirements and parameters are listed in Table 1, 4.1 to 4.19. I
46、f there are no specific declarations stated by the customer, then the declarations stated by the manufacturer should be taken as the basis for the requirements and parameters. The following distinction shall be made between the manufacturer and customer/user: Declarations which the customer or the u
47、ser of the generating set are required to provide; Declarations which the manufacturer of the generating set are required to provide; Declarations to be agreed between the manufacturer and customer/user. These are indicated by symbol “X” in Table 1, columns “M” (manufacturer) and “C” (customer) of 4
48、.1 to 4.19.2 ISO 2017 All rights reserved ISO 8528-7:2017(E) Table 1 Important technical requirements and parameters No. Term Item Reference C MPower demand X Power factor X Rated frequency X Rated voltage X Type of system earthing IEC 60364-4-41 X 4.1 Basic data Profile of the connected electri- ca
49、l load ISO 8528-5:2013, 9.1 ISO 8528-1:2005, 6.1 to 6.3 X Required steady-state frequen- cy and voltage behaviour ISO 8528-5:2013, 5.1 and Clause 7 X XRequired transient frequency and voltage behaviour ISO 8528-5:2013, 5.1 and Clause 7 X XType of fuel available ISO 8528-2:2005, Clause 12 X Fuel system safety construction ISO 8528-13, 6.13 X XStarting ISO 8528-5:2013, 15.1 and ISO 8528-7, C.3.11 X XCooling and room ventilation ISO 8528-5:2
