1、BSI Standards Publication BS ISO/IEC 24769-62:2015 Information Technology Real Time Locating System (RTLS) Device Conformance T e s t M e t h o d s Part 62: High rate pulse repetition frequency Ultra Wide Band (UWB) air interfaceBS ISO/IEC 24769-62:2015 BRITISH STANDARD National foreword This Britis
2、h Standard is the UK implementation of ISO/IEC 24769-62:2015. The UK participation in its preparation was entrusted to Technical Committee IST/34, Automatic identification and data capture techniques. A list of organizations represented on this committee can be obtained on request to its secretary.
3、This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2015. Published by BSI Standards Limited 2015 ISBN 978 0 580 82932 1 ICS 35.040 Compliance with a British Standard cannot conf
4、er immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2015. Amendments/corrigenda issued since publication Date T e x t a f f e c t e dBS ISO/IEC 24769-62:2015 Information Technology Real Time Locating
5、 System (RTLS) Device Conformance Test Methods Part 62: High rate pulse repetition frequency Ultra Wide Band (UWB) air interface Technologies de linformation Mthodes dessai de conformit du dispositif des systmes de localisation en temps rel (RTLS) Partie 62: Mthodologie de test de interface arienne
6、ultra large bande (UWB) impulsions haute frquence de rptition INTERNATIONAL STANDARD ISO/IEC 24769-62 Reference number ISO/IEC 24769-62:2015(E) First edition 2015-10-01 ISO/IEC 2015 BS ISO/IEC 24769-62:2015ii ISO/IEC 2015 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2015, Published in Sw
7、itzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be
8、 requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.org ISO/IEC 24769-62:2015(E)BS ISO/IEC 24769-6
9、2:2015ISO/IEC 24769-62:2015(E)Foreword iv Introduction v 1 Scope . 1 2 Normative references 1 3 T erms, definitions and abbr e viat ed t erms 1 3.1 Terms and definitions . 1 3.2 Abbreviated terms . 1 4 Conformance tests for ISO/IEC 24730-62. 2 4.1 General . 2 4.2 Default conditions applicable to the
10、 test methods 2 4.2.1 Preface 2 4.2.2 Test environment 2 4.2.3 Default tolerance 2 4.2.4 Noise floor at test location. 2 4.2.5 Total measurement uncertainty . 3 4.3 UWB RF transmission tests 3 4.3.1 General 3 4.3.2 Test Objective 3 4.3.3 Test procedure . 3 4.3.4 Test measurements and requirements .
11、4 4.3.5 Test report . 4 4.4 Receiver UWB RF tests . 4 4.4.1 Preface 4 4.4.2 General 4 4.4.3 Test objective 5 4.4.4 Test procedure . 5 4.4.5 Test measurements and requirements . 5 4.4.6 Test report . 5 Annex A (normative) RF test measurement site. 6 ISO/IEC 2015 All rights reserved iii Contents PageB
12、S ISO/IEC 24769-62:2015ISO/IEC 24769-62:2015(E) Foreword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the devel
13、opment of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmen
14、tal, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Dire
15、ctives, Part 1. In particular the different approval criteria needed for the different types of document should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some o
16、f the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent de
17、clarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as informati
18、on about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT), see the following URL: Foreword Supplementary information. The committee responsible for this document is ISO/IEC JTC 1, Information technology, Subcommittee SC 31, Automatic identification and data capture techn
19、iques. ISO/IEC 24769 consists of the following parts, under the general title Information technology Real- time locating systems (RTLS) device conformance test methods: Part 2: Test methods for air interface communication at 2,4 GHz Part 5: Test methods for chirp spread spectrum (CSS) at 2,4 GHz air
20、 interface Part 61: Low rate pulse repetition frequency Ultra Wide Band (UWB) air interface Part 62: High rate pulse repetition frequency Ultra Wide Band (UWB) air interfaceiv ISO/IEC 2015 All rights reservedBS ISO/IEC 24769-62:2015ISO/IEC 24769-62:2015(E) Introduction ISO/IEC 24730-62 defines an ai
21、r interface for ultra wide band (UWB) Real Time Locating Systems (RTLS) devices used in asset management applications. This International Standard contains all measurements required to be made on a product in order to establish whether it conforms to ISO/IEC 24730-62. Test methods for measuring perf
22、ormance of equipment compliant with ISO/IEC 24730-62 are given in ISO/IEC 24770-62. ISO/IEC 2015 All rights reserved vBS ISO/IEC 24769-62:2015BS ISO/IEC 24769-62:2015Information Technology Real Time Locating System (RTLS) Device Conformance Test Methods Part 62: High rate pulse repetition frequency
23、Ultra Wide Band (UWB) air interface 1 Scope This International Standard defines the test methods for determining the conformance of Ultra Wide Band real-time locating system (RTLS) tags with the specifications given in the corresponding parts of ISO/IEC 24730-62, but does not apply to the testing of
24、 conformity with regulatory or similar requirements. The test methods require only that the mandatory functions, and any optional functions which are implemented, be verified. This may in appropriate circumstances, be supplemented by further, application specific functionality criteria that are not
25、available to the general case. Unless otherwise specified, the tests in this International Standard apply exclusively to RTLS tags defined in ISO/IEC 24730-62. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for i
26、ts application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/IEC 19762-1, Information technology Automatic identification and data capture (AIDC) techniques Harmonized vocabulary Pa
27、rt 1: General terms relating to AIDC ISO/IEC 19762-3, Information technology Automatic identification and data capture (AIDC) techniques Harmonized vocabulary Part 3: Radio frequency identification (RFID) ISO/IEC 24730-62:2013, Information technology Real time locating systems (RTLS) Part 62: High r
28、ate pulse repetition frequency Ultra Wide Band (UWB) air interface 3 T erms, d efinitions and abbr e viat ed t erms 3.1 T erms and definiti ons For the purposes of this document, the terms and definitions given in ISO/IEC 19762-3 apply. 3.2 A bbr e viat ed t erms CRC cyclic redundancy check DUT devi
29、ce under test PHR PHY header PHY physical layer INTERNATIONAL ST ANDARD ISO/IEC 24769-62:2015(E) ISO/IEC 2015 All rights reserved 1BS ISO/IEC 24769-62:2015ISO/IEC 24769-62:2015(E) PPM parts per million PRF pulse repetition frequency PSD power spectral density RBW resolution bandwidth RF radio freque
30、ncy RFID radio frequency identification RTLS real time locating system SFD start-of-frame delimiter VBW video bandwidth UWB ultra wide band 4 Conformance tests for ISO/IEC 24730-62 4.1 General This International Standard specifies a series of tests to determine the conformance of RTLS tags to the IS
31、O/IEC 24730-62 air interface standard. The results of these tests shall be compared with the values of the parameters specified in ISO/IEC 24730-62 to determine whether the tag under test conforms. This International Standard also specifies a series of tests to determine the conformance of RTLS RF r
32、eceivers to the ISO/IEC 24730-62 air interface standard. The results of these tests shall be compared with the values of the parameters specified in ISO/IEC 24730-62 to determine whether the RF receiver under test conforms. 4.2 Default c onditions applicable t o the t est methods 4.2.1 Preface These
33、 conditions apply to all tests. 4.2.2 Test environment Unless otherwise specified, testing shall take place in an environment of temperature 23 C 3 C (73 F 5 F) and of relative humidity 25 % to 75 %. 4.2.3 Default tolerance Unless otherwise specified, a default tolerance of 5 % shall be applied to t
34、he quantity values given to specify the characteristics of the test equipment and the test method procedures. 4.2.4 Noise floor at t est location Noise floor at test location shall be measured with the spectrum analyser in the same conditions as the measurement of the DUT, i.e. with same span, RBW,
35、VBW and antenna. The spectrum analyser shall be configured in acquisition mode for at least 1 min.2 ISO/IEC 2015 All rights reservedBS ISO/IEC 24769-62:2015ISO/IEC 24769-62:2015(E) The maximum of the measured amplitude shall be at least 60 dB TBC below the expected value of the amplitude of the meas
36、ured tag transmission at 16 dBm power with the tag placed at 1 m from the measurement antenna. Special attention has to be given to spurious emissions, e.g. insufficiently shielded computer monitors. The electromagnetic test conditions of the measurements shall be checked by performing the measureme
37、nts with and without a tag in the field. 4.2.5 Total measurement uncertainty The test equipment will introduce a level of measurement uncertainty. The specifications of the test equipment used shall be included in the report. 4.3 UWB RF transmission tests 4.3.1 General The DUT shall be an RTLS tag.
38、The measurement equipment shall consist of an anechoic chamber as described in Annex A, a calibrated measuring antenna, a spectrum analyser such as a Rohde and Schwarz FSU26 1)and a suitable receiver consisting of an RF amplifier, signal generator, mixer and a high speed oscilloscope such as an Agil
39、ent DSA90804A 2) . Figure 1 shows the test equipment setup. Figure 1 General setup of equipment for UWB tag RF test 4.3.2 T est Objecti v e The objective of this test is to verify that the RTLS tag provides the appropriate UWB modulation waveform required for proper system performance. 4.3.3 Test pr
40、ocedure The tag shall be configured to transmit the maximum length UWB blink that it is intended to send when deployed. The post processing software shall produce metrics for the following parameters to verify compliance of the tag. 1) The Rohde & Schwarz FSU26 is an example of a suitable product av
41、ailable commercially. This information is given for the convenience of users of this standard and does not constitute an endorsement by ISO of this product. 2) The Agilent DSA90804A is an example of a suitable product available commercially. This information is given for the convenience of users of
42、this standard and does not constitute an endorsement by ISO of this product. ISO/IEC 2015 All rights reserved 3BS ISO/IEC 24769-62:2015ISO/IEC 24769-62:2015(E) 4.3.4 Test measurements and requirements 4.3.4.1 Spectral mask The spectral mask shall be in accordance with ISO/IEC 24730-62:2013, 5.5.3.2,
43、 for the channel or channels in which the tag operates. 4.3.4.2 Transmit power The transmitted power shall be calculated based on the power received at the measurement antenna. The calculated power shall be within 2.0 dB of the DUT specified transmit power. Transmit power and spectral density mask s
44、hall conform to regulatory constraints for the intended operating region. 4.3.4.3 Transmitter timing The transmitter shall be capable of chipping at the peak PRF given in ISO/IEC 24730-62:2013, Table 3 with an accuracy of 20 ppm. In addition the operating channel centre of transmitted energy shall b
45、e at the appropriate value listed in ISO/IEC 24730-62:2013, Table 11 also with an accuracy of 20 ppm. The measurements shall be made using 1 MHz resolution bandwidth and a 1 kHz video bandwidth. 4.3.4.4 Message content and structure The post processing software shall verify the selected message form
46、at including preamble, SFD, PHR and data payload are in compliance with the format specified in ISO/IEC 24730-62, all of which are dependent on the selected operational modes, PRF, preamble code, data rate and payload content. 4.3.5 Test report The test report shall contain the tag distance to the m
47、easurement antenna and all of the measured data. A brief narrative of the post processing software used to evaluate the captured signal shall also be included as an annex to the data. As mentioned before (in 4.2.4), the report shall also contain the uncertainties of the measurement equipment. 4.4 Re
48、ceiver UWB RF tests 4.4.1 Preface This clause describes the conformance tests for the UWB receiver of the RTLS (reader) nodes, and for those tags supporting ISO/IEC 24730-62 optional two-way communications mode. 4.4.2 General The DUT shall be an RTLS RF receiver operating in one or more of the chann
49、els and operating modes specified in ISO/IEC 24730-62. Example test/measurement equipment could consist of an a tag generator capable of producing an ISO/IEC 24730-62 compliant UWB message in the channel and operating modes supported and configured in the receiver of the DUT.4 ISO/IEC 2015 All rights reservedBS ISO/IEC 24769-62:2015ISO/IEC 24769-62:2015(E) Figure 2 Setup of equipment for UWB receiver RF Test 4.4.3 T est objecti v e The obje
