1、BRITISH STANDARD BS ISO TR 11761:1992 Implementation of ISO TR 11761:1992 Light-gauge metal containers Roundopen-top cans Classification of can sizes by construction type UDC 621.798.1:672.46.001.33BSISO TR 11761:1992 This British Standard, having been prepared under the directionof the Consumer Pro
2、ducts and Services Sector Board, was published under theauthority of the Standards Board and comes into effect on 15January 1996 BSI 01-2000 The following BSI references relate to the work on this standard: Committee reference PKW/2 Draft announced in BSINews June 1995 ISBN 0 580 25304 X Committees
3、responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee PKW/2, Primary packaging, upon which the following bodies were represented: Association of the British Pharmaceutical Industry British Aerosol Manufacturers Association British Fibrebo
4、ard Packaging Association British Glass Manufacturers Confederation British Plastics Federation British Retail Consortium Chemical Industries Association Cosmetic, Toiletry and Perfumery Association Limited Department of Trade and Industry (Consumer Safety Unit, CA Division) Department of Trade and
5、Industry (Laboratory of the Government Chemist) Environmental and Technical Association for the Paper Sack Industry Flexible Packaging Association Institute of Packaging Institute of Trading Standards Administration Institute of Wastes Management Metal Packaging Manufacturers Association Packaging a
6、nd Industrial Films Association Paper Federation of Great Britain Pira International The following bodies were also represented in the drafting of the standard, through subcommittees and panels: British Coatings Federation Ltd. British Compressed Gases Association Consumer Policy Committee of BSI En
7、gineering Equipment and Materials Users Association Health and Safety Executive LP Gas Association Society of Cosmetic Scientists Amendments issued since publication Amd. No. Date CommentsBSISO TR 11761:1992 BSI 01-2000 i Contents Page Committees responsible Inside front cover National foreword ii F
8、oreword iii Text of ISO TR 11761 1BSISO TR 11761:1992 ii BSI 01-2000 National foreword This British Standard reproduces verbatim ISO TR 11761:1992 and implements it as the UK national standard. Together with BS ISO 10653, BS ISO 10654, BSISO TR 11762 and BS ISO TR 11776, this British Standard supers
9、edes BS6992-1:1988, BS 6992-2:1991, BS 6992-3:1988, BS 6992-4:1989 and BS 6992-5:1988, which are withdrawn. This British Standard is published under the direction of the Consumer Products and Services Sector Board whose Technical Committee PKW/2 has the responsibility to: aid enquirers to understand
10、 the text; present to the responsible international committee any enquiries on interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK. NOTEInternational and European Standards, as well as overseas
11、 standards, are available from Customer Services, BSI, 389 Chiswick High Road, London W4 4AL. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does n
12、ot of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theISOTR title page, pages ii to iv, pages1 to6 and abackcover. This standard has been updated (see copyright date) and may have had amendments incorporat
13、ed. This will be indicated in the amendment table on the inside front cover.ISO/TR 11761:1992(E) ii BSI 01-2000 Contents Page Foreword iii 1 Scope 1 2 References 1 3 Designation of containers (types and construction) 1 4 List of nominal gross lidded capacities and nominal diameters 2 Annex A Referen
14、ce list 6 Table 1 2 Table 2 3 Table 3 3 Table 4 4 Table 5 4 Table 6 5 Table 7 5 Table A.1 6ISO/TR 11761:1992(E) BSI 01-2000 iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing Internat
15、ional Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with I
16、SO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The main task of technical committees is to prepare International Standards, but in exceptional circumstances a technical committee ma
17、y propose the publication of a Technical Report of one of the following types: type 1, when the required support cannot be obtained for the publication of an International Standard, despite repeated efforts; type 2, when the subject is still under technical development or where for any other reason
18、there is the future but not immediate possibility of an agreement on an International Standard; type 3, when a technical committee has collected data of a different kind from that which is normally published as an International Standard (“state of the art”, for example). Technical Reports of types 1
19、 and 2 are subject to review within three years of publication, to decide whether they can be transformed into International Standards. Technical Reports of type 3 do not necessarily have to be reviewed until the data they provide are considered to be no longer valid or useful. ISO/TR 11761, which i
20、s a Technical Report of type 3, was prepared by Technical Committee ISO/TC 52, Light gauge metal containers. It gives, for information, a list of can sizes standardized in ISO 10653 but classified by construction type. NOTEISO 10653 specifies only nominal gross lidded capacities and nominal diameter
21、s. Together with ISO 10653, ISO 10654, ISO/TR 11762 and ISO/TR 11776, this first edition of ISO/TR 11761 cancels and replaces ISO 3004-1:1986, ISO 3004-2:1989, ISO 3004-3:1986, ISO 3004-4:1986, ISO 3004-5:1988 and ISO 3004-6:1986. Annex A of this Technical Report is for information only. It lists th
22、e can sizes previously standardized in ISO 3004-1, ISO 3004-2, ISO 3004-3 (except for sub-clause 3.1), ISO 3004-4, ISO 3004-5 and ISO 3004-6.iv blankISO/TR 11761:1992(E) BSI 01-2000 1 1 Scope This Technical Report gives a list of nominal gross lidded capacities and nominal diameters for round open t
23、op cans presented by construction type. 2 References ISO 90-1, Light gauge metal containers Definitions and determination methods for dimensions and capacities Part 1: Open-top cans. ISO 1361, Light gauge metal containers Open-top cans Round cans Internal diameters. ISO 10653, Light gauge metal cont
24、ainers Round open-top cans Cans defined by their nominal gross lidded capacities. 3 Designation of containers (types and construction) The definitions, designations and special features of these types of containers (necked-in and/or step-sided) are given in ISO 90-1. This Technical Report concerns t
25、he following containers: 3 piece, straight-sided cans; 3 piece, single necked-in cans; 3 piece, tapered cans; 2 piece, straight-sided cans; 2 piece, step-sided cans; 2 piece, tapered cans; 2 piece, tapered, step-sided cans.ISO/TR 11761:1992(E) 2 BSI 01-2000 4 List of nominal gross lidded capacities
26、and nominal diameters 4.1 Open top cans Round 3 piece, straight-sided Table 1 Nominal gross lidded capacity (ml) Nominal diameter D (mm) 71 52 85 65, 73 106 65 125 73 142 52, 73 156 65 170 52, 83 198 73 212 65, 73, 83 228 73 236 65 314 65, 73, 99 403 73 425 73, 83, 99 446 73 580 83 636 99 850 1 062
27、83, 99 1 275 99 1 700 99, 153 1 800 99 2 650 153 3 100 4 250 10 200 230ISO/TR 11761:1992(E) BSI 01-2000 3 4.2 Open top cans round 3 piece, single-necked-in Table 2 4.3 Open-top cans round 3 piece, tapered Table 3 Nominal gross lidded capacity (ml) Nominal diameter D mm 212 65 425 73, 83, 99 850 99 1
28、0 200 230 Nominal gross lidded capacity (ml) Nominal diameter D1 (mm) 10 200 230ISO/TR 11761:1992(E) 4 BSI 01-2000 4.4 Open top cans round 2 piece, straight-sided Table 4 4.5 Open top cans round 2 piece, step-sided Table 5 Nominal gross lidded capacity (ml) Nominal diameter D (mm) 85 65 106 65 125 7
29、3 142 52 170 63, 83 198 73 212 63, 65, 73, 83 314 65, 99 403 73 425 73, 83, 99 446 73 580 83 850 99 Nominal gross lidded capacity (ml) Nominal diameter (mm) 71 63 85 63, 65, 73 125 73 142 73 170 83 212 63, 65, 73, 83 314 99 425 83, 99ISO/TR 11761:1992(E) BSI 01-2000 5 4.6 Open top cans round 2 piece
30、, tapered Table 6 4.7 Open top cans round 2 piece, tapered, step-sided Table 7 NOTECalculation method for the nominal diameter: to be studied. Nominal gross lidded capacity (ml) Nominal diameter (mm) 125 73 425 99 Nominal gross lidded capacity (ml) Nominal diameter (mm) 85 63 125 73 142 73 212 73, 8
31、3 314 99 425 99ISO/TR 11761:1992(E) 6 BSI 01-2000 Annex A Reference list The following can sizes were standardized in the former ISO 3004 Standard but now these cans do not meet the required criteria to be standardized and incorporated in ISO 10653. Table A.1 Volume Diameter 42 52 58 60 63 65 73 78
32、83 99 105 127 153 171 230 57 60 85 106 115 125 142 170 182 198 212 228 246 250 257 275 283 296 340 355 390 446 475 492 580 620 684 720 825 850 1 062 1 100 1 135 1 455 1 700 2 160 5 400 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x
33、 xblankBS ISO TR 11761:1992 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Rev
34、isions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or amb
35、iguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers auto
36、matically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI
37、implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electroni
38、c information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of stand
39、ards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under
40、 the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of impleme
41、nting the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.
