1、PD CEN/TR 15276-1:2009 ICS 13.220.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW PUBLISHED DOCUMENT Fixed firefighting systems Condensed aerosol extinguishing systems Part 1: Requirements and test methods for componentsThis Published Document was published under the author
2、ity of the Standards Policy and Strategy Committee on 30 April 2009. BSI 2009 ISBN 978 0 580 54126 1 Amendments/corrigenda issued since publication Date Comments PD CEN/TR 15276-1:2009 National foreword This Published Document is the UK implementation of CEN/TR 15276-1:2009. The UK participation in
3、its preparation was entrusted to Technical Committee FSH/18/6, Gaseous extinguishing media and systems. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users ar
4、e responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations.PD CEN/TR 15276-1:2009 TECHNICAL REPORT RAPPORT TECHNIQUE TECHNISCHER BERICHT CEN/TR 15276-1 January 2009 ICS 13.220.20 English Version Fixed firefighting systems - Condensed a
5、erosol extinguishing systems - Part 1: Requirements and test methods for components Installations fixes de lutte contre lincendie - Systmes dextinction arosol - Partie 1 : Exigences et mthodes dessais pour les lments constitutifs Ortsfeste Brandbekmpfungsanlagen - Lschanlagen fr kondensierte Aerosol
6、e - Teil 1: Anforderungen und Prfverfahren fr Bauteile This Technical Report was approved by CEN on 9 September 2008. It has been drawn up by the Technical Committee CEN/TC 191. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Fin
7、land, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES
8、KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN/TR 15276-1:2009: EPD CEN/TR 15276-1:2009 CEN/TR 15276-1:2009 (E) 2 Contents Page Foreword 4 Introductio
9、n .5 1 Scope 6 2 Normative references 6 3 Terms and definitions .7 4 Component requirements .9 4.1 Condensed aerosol generator 9 4.2 Solid aerosol-forming compound 9 4.3 Cooling mechanism .9 4.4 Ignition device 9 4.4.1 General 9 4.4.2 Electrical ignition device .9 4.4.3 Thermal ignition device .9 4.
10、4.4 Other methods of ignition device.9 4.5 End plate and housing . 10 4.6 Extinguishants 10 5 Condensed aerosol generators requirements . 10 5.1 General . 10 5.2 Extinguishing factor . 10 5.3 Agent distribution . 10 5.4 Discharge time 10 5.5 Ambient temperature and humidity operation ranges 10 5.6 S
11、ervice life . 10 5.7 Shelf life and storage conditions 11 5.8 Corrosion . 11 5.9 Vibration 11 5.10 Mechanical shock . 11 5.11 Discharge temperature . 11 5.11.1 General . 11 5.11.2 Casing temperature 11 5.11.3 Aerosol flow temperature 11 5.12 Ignition device . 11 5.12.1 General . 11 5.12.2 Electrical
12、 ignition device 11 5.12.3 Thermal ignition device 12 5.13 Function reliability 12 5.14 Open fire conditions . 12 5.15 Accessories . 12 5.16 Documentation 12 6 Marking 12 7 Test methods . 13 7.1 Conditions . 13 7.2 Samples . 13 7.3 Conformity . 14 7.4 Extinguishing factor determination 14 7.5 Covera
13、ge determination . 14 7.6 Discharge time test . 14 7.7 Temperature and humidity operation range tests . 15 PD CEN/TR 15276-1:2009 CEN/TR 15276-1:2009 (E) 3 7.7.1 Object of the test . 15 7.7.2 Test procedure . 15 7.7.3 Low temperature Test . 15 7.8 Accelerated ageing test 15 7.8.1 Test time . 15 7.8.
14、2 Test procedure . 16 7.9 Corrosion test 16 7.10 Stress corrosion test. 17 7.11 Vibration test 17 7.12 Impact test 18 7.12.1 Test procedure . 18 7.12.2 Test apparatus . 18 7.13 Drop test . 20 7.13.1 Impact surface . 20 7.13.2 Procedure . 20 7.13.3 Requirements . 20 7.14 Casing and aerosol flow tempe
15、ratures test 20 7.14.1 Casing temperature test . 20 7.14.2 Aerosol flow temperature test 20 7.15 Ignition performance test . 20 7.16 Function test 20 7.16.1 Discharge time . 21 7.16.2 Aerosol flow temperatures . 21 7.16.3 Test procedure . 21 7.16.4 Casing temperature test . 21 7.16.5 Discharged mass
16、 . 21 7.16.6 Explosive atmosphere actuation test 21 7.16.7 Requirements . 22 7.17 Heat exposure test 22 7.17.1 Object of the test . 22 7.17.2 Test procedure . 22 7.17.3 Requirements . 22 7.18 Explosive atmosphere test . 22 7.18.1 Object of the test. 22 7.18.2 Test procedure . 23 7.18.3 Requirements
17、. 23 Annex A (normative) Extinguishing factor/coverage test procedure 24 Bibliography 47 PD CEN/TR 15276-1:2009 CEN/TR 15276-1:2009 (E) 4 Foreword This document (CEN/TR 15276-1:2009) has been prepared by Technical Committee CEN/TC 191 “Fixed firefighting systems”, the secretariat of which is held by
18、 BSI. This document has the general title Fixed fire-fighting systems Condensed aerosol extinguishing systems and will consist of the following parts: Part 1: Requirements and test methods for components; Part 2: Design, installation and maintenance. PD CEN/TR 15276-1:2009 CEN/TR 15276-1:2009 (E) 5
19、Introduction It has been assumed in the preparation of this document that the execution of its provisions is entrusted to appropriately qualified and experienced people in the specification, design, installation, testing, approval, inspection, operation and maintenance of systems and equipment, for
20、whose guidance it has been prepared, and who can be expected to exercise a duty of care to avoid unnecessary release of extinguishant. Product certification: Users of this document are advised to consider the desirability of independent certification of product conformity with this document based on
21、 testing and continuing surveillance, which may be coupled with assessment of manufacturer quality systems against EN ISO 9001. Fire-fighting systems covered in this document are designed to provide a supply of fixed condensed aerosol extinguishing medium to extinguish fire. The requirements of this
22、 document are made in the light of the best technical data known to the working group at the time of writing but, since a wide field is covered, it has been impracticable to consider every possible factor or circumstance that might affect implementation of the requirements. It is important that the
23、fire protection of a building or plant be considered as a whole. Aerosol extinguishant systems form only a part, though an important part, of the available facilities, but it should not be assumed that their adoption necessarily removes the need to consider supplementary measures, such as the provis
24、ion of portable fire extinguishers or other mobile appliances for first aid or emergency use, or to deal with special hazards. Aerosol extinguishants have been recognized as effective media for the extinction of Class A fires (solid surface burning fires) and Class B and Class C fires according to E
25、N 2, but it should not be forgotten, in the planning of comprehensive schemes, that there may be hazards for which these mediums are not suitable, or that in certain circumstances or situations there may be dangers in their use requiring special precautions. Advice on these matters can be obtained f
26、rom the appropriate manufacturer of the aerosol generators or the extinguishing system. Information may also be sought from the appropriate fire authority, the health and safety authorities and insurers. In addition, reference should be made as necessary to other national standards and statutory reg
27、ulations. It is essential that fire-fighting equipment be carefully maintained to ensure instant readiness when required. Routine maintenance is liable to be overlooked or given insufficient attention by the owner of the system. It is, however, neglected at peril to the lives of occupants of the pre
28、mises and at the risk of crippling financial loss. The importance of maintenance cannot be too highly emphasised. Condensed aerosol may contain traces of toxic substances like those produced by a fire, and will obscure vision like smoke from fire. PD CEN/TR 15276-1:2009 CEN/TR 15276-1:2009 (E) 6 1 S
29、cope This document specifies requirements, describes test methods for condensed aerosol extinguishing components and covers solely condensed aerosols. This document is not intended to indicate approval of the extinguishants listed herein by the appropriate authorities, as other extinguishants may be
30、 equally acceptable. This document is intended as a standard covering solely condensed aerosol. The condensed aerosol generator typically consists of the following main components: a) solid aerosol-forming compound; b) cooling mechanism; c) ignition device(s); d) end plate discharge outlet(s); e) ho
31、using; f) mounting bracket. This document does not cover dispersed aerosols. This document requires, as a precaution, that the room is evacuated and sealed off whenever a generator is activated. Precautions include evacuation of the proximity area, criteria for re-entering and other safeguards as st
32、ated in Clause 5 of CEN/TR 15276-2:2009. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendm
33、ents) applies. EN 316, Wood fibreboards Definition, classification and symbols EN 622 (all parts), Fibreboards Specifications EN 60068-2-6, Environmental testing Part 2-6: Tests Test Fc: Vibration (sinusoidal) (IEC 60068-2-6:2007) EN 60068-2-30, Environmental testing Part 2-30: Tests Test Db: Damp H
34、eat, cyclic (12 h + 12 h cycle) (IEC 60068-2-30:2005) ISO 209, Aluminium and aluminium alloys Chemical composition ISO 5660-1, Reaction-to-fire tests Heat release, smoke production and mass loss rate Part 1: Heat release rate (cone calorimeter method) PD CEN/TR 15276-1:2009 CEN/TR 15276-1:2009 (E) 7
35、 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 authority organisation, office or individual responsible for approving equipment, installations or procedures in determining acceptability NOTE The authority may base acceptance on conformity t
36、o the appropriate standards. 3.2 clearance 3.2.1 electrical clearance unobstructed air distance between extinguishing system equipment and unenclosed or uninsulated live electrical components not at ground potential 3.2.2 thermal clearance air distance between a condensed aerosol generator and any s
37、tructure or components sensitive to the temperature developed by the generator 3.3 condensed aerosol extinguishing medium consisting of finely divided solid particles and gaseous matter, these being generated by a combustion process of a solid aerosol-forming compound 3.4 condensed aerosol generator
38、 non-pressurised device which, when activated, generates an aerosol. It includes the mounting brackets 3.5 design factor extinguishing factor multiplied by the safety factor, required for system design purposes NOTE 1 The design factor is expressed in grams per cubic metre. NOTE 2 Extinguishing fact
39、or and design factor have been introduced as an alternative to extinguishing concentration and design concentration respectively as concentration of the actual aerosol cannot be measured or even assessed in some cases (the discharged medium, apart from the condensed aerosol, may contain products of
40、the thermal decomposition of a chemical coolant). 3.6 discharge time time from the generator activation to the end of its discharge 3.7 extinguishing application density minimum mass of a specific aerosol-forming compound per cubic metreof enclosure volume required to extinguish fire involving a spe
41、cific fuel under defined experimental conditions, excluding any safety factors NOTE The extinguishing factor is expressed in grams per cubic metre. 3.8 family group of generators with same solid compound, same kind of cooling device, same kind of discharge outlet, same ignition device, same layout a
42、nd same internal/external architecture PD CEN/TR 15276-1:2009 CEN/TR 15276-1:2009 (E) 8 3.9 ignition device any device which is able to ignite the solid aerosol-forming compound 3.10 listing authority recognized fire protection testing and approval body (notified laboratory) 3.11 maintenance thoroug
43、h check to give maximum assurance that the extinguishing system will operate as intended NOTE It includes a thorough examination and any necessary repair or replacement of system components. 3.12 manufacturer legal person that is responsible for the design, manufacturing, packaging and quality assur
44、ance of a device before it is placed on the market 3.13 monitoring supervision of the operating integrity of an electrical, mechanical, pneumatic or hydraulic control feature of a system 3.14 protected volume volume enclosed by the building elements around the protected enclosure, minus the volume o
45、f any permanent impermeable building element within the enclosure 3.15 release physical discharge or emission of an aerosol as a consequence of the generator actuation 3.16 safety factor multiplier of the extinguishing factor to determine the design factor 3.17 solid aerosol-forming compound mixture
46、 of oxidant, combustible component and technical admixtures producing fire extinguishing aerosol upon ignition 3.18 supplier legal person that is responsible for the product and is able to ensure that its quality is ensured 3.19 thermal ignition device device which automatically operates at a rated
47、temperature and is arranged for the ignition of the solid aerosol-forming compound 3.20 test house establishment having all relevant test equipment to carry out the required tests PD CEN/TR 15276-1:2009 CEN/TR 15276-1:2009 (E) 9 4 Component requirements 4.1 Condensed aerosol generator The condensed
48、aerosol generator typically consists of the following main components: a) solid aerosol-forming compound; b) cooling mechanism; c) ignition device(s); d) end plate discharge outlet(s); e) housing; f) mounting bracket. The generator is a non-pressurised canister, because aerosol is generated and dist
49、ributed by the combustion process of the solid aerosol-forming compound. 4.2 Solid aerosol-forming compound Upon actuation of the condensed aerosol generator, the solid aerosol-forming compound shall undergo the combustion reaction producing a fire extinguishing aerosol. 4.3 Cooling mechanism The cooling mechanism shall provide an adequate cooling of the hot aerosol prior to its discharge into the enclosure. 4.4 Ignition device 4.4.1 General The ignition device is arranged to initiate the aerosol-forming compound. If the ignition device is a com
