1、BSI Standards Publication PD ISO/TR 13392:2014 Health and safety in welding and allied processes Arc welding fume componentsPD ISO/TR 13392:2014 PUBLISHED DOCUMENT National foreword This Published Document is the UK implementation of ISO/TR 13392:2014. The UK participation in its preparation was ent
2、rusted to Technical Committee WEE/40, Health and safety in welding. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct applic
3、ation. The British Standards Institution 2014. Published by BSI Standards Limited 2014 ISBN 978 0 580 86903 7 ICS 13.100; 25.160.01 Compliance with a British Standard cannot confer immunity from legal obligations. This Published Document was published under the authority of the Standards Policy and
4、Strategy Committee on 31 August 2014. Amendments issued since publication Date Text affectedPD ISO/TR 13392:2014 Health and safety in welding and allied processes Arc welding fume components Hygine et scurit en soudage et techniques connexes Composants des fumes de soudage dans larc First edition 20
5、14-09-01 ISO 2014 ISO/TR 13392 TECHNICAL REPORT Reference numbers ISO/TR 13392:2014(E)PD ISO/TR 13392:2014ISO/TR 13392:2014(E) ii ISO 2014 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utili
6、zed otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyrigh
7、t office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandPD ISO/TR 13392:2014ISO/TR 13392:2014(E) ISO 2014 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative reference
8、s 1 3 T erms and definitions . 1 4 Background 1 Bibliography 3PD ISO/TR 13392:2014ISO/TR 13392:2014(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normal
9、ly carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the
10、 work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the
11、different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this docume
12、nt may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/
13、patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO pr
14、inciples in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information ISO/TR 13392 was prepared by the International Institute of Welding, Commission VIII Health and Safety. IIW is recognized as an international standardizing body in the field of welding in ac
15、cordance with Council Resolution 42/1999. iv ISO 2014 All rights reservedPD ISO/TR 13392:2014ISO/TR 13392:2014(E) Introduction This Technical Report constitutes the considered judgement of experts on the range of principal components of fume which can be emitted from arc welding processes and identi
16、fies, as key components, those which are of greatest occupational hygiene significance and therefore require the most stringent control measures to ensure that a welder is not exposed to an excessive level of the substance concerned. The report is intended to assist in hazard appreciation, risk asse
17、ssment and risk control and thus contribute to improving the health and safety of welders and those working with them. It is also intended to assist medical professionals in their care of welders and others exposed to welding fume. The constituent components of particular consumables and the fume ar
18、ising from their use should be gained from the Safety Data Sheet produced by the manufacturer and supplied with the consumables. ISO 2014 All rights reserved vPD ISO/TR 13392:2014PD ISO/TR 13392:2014Health and safety in welding and allied processes Arc welding fume components 1 Scope This Technical
19、Report provides guidance, based on the experiences of experts, on the components of fume emitted from a range of arc welding processes and consumable types. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its
20、application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/TR 25901, Welding and related processes Vocabulary 3 T erms a nd definiti ons For the purposes of this document, the terms
21、and definitions given in ISO/TR 25901 apply. 4 Background Arc welding processes emit fume. This is a complex, dynamic mixture of particulates derived mainly from the welding consumable but also the metal and any coatings and contaminants present. Most of the particles are in the respirable range whi
22、ch means that they can penetrate to the innermost area of the lung where they have the greatest potential to do harm. Many particles contain metal compounds, often as complex oxides and sometimes within a core surrounded by a shell. Some of the components of the fume are at least potentially biologi
23、cally active. It is essential to be aware of these components when undertaking health and safety risk assessments of welding processes. Table 1 1)provides a general awareness to those responsible for making assessments or for the health care of welders and those who work with them. It identifies the
24、 principal and key components likely to be contained within the fume from a range of welding processes and consumable types. In this context, a principal component 2)is a component that is of some occupational hygiene significance while the key component 3)is the one that has the greatest occupation
25、al hygiene significance and therefore requires the most stringent control measures to ensure that a welder is not exposed to an excessive level of the substance concerned, i.e. it is the component whose limit value is exceeded at the lowest welding fume concentration. 1) This table is derived from t
26、hat shown in ISO 15011-4. 2) A principal component is a component of occupational hygiene significance. 3) Key components have the greatest occupational hygiene significance and therefore require the most stringent control measures to ensure that a welder is not exposed to an excessive level of the
27、substance(s) concerned, i.e. a component whose limit value is exceeded at the lowest welding fume concentration. TECHNICAL REPORT ISO/TR 13392:2014(E) ISO 2014 All rights reserved 1PD ISO/TR 13392:2014ISO/TR 13392:2014(E) Table 1 Principal and key components of commonly encountered arc welding fumes
28、 Type of process a Type of consumable Typical principal components Other possible principal compo- nents Typical key component MMA (SMAW) 111 Unalloyed and low alloy steel b Fe, Mn, Cr, Cr(VI) Ni, Cu F Mn, Cr or Cr(VI) d High alloy steel c Cr, Cr(VI), Fe, Mn, Ni F Cr(VI) or Ni Aluminium Al, Cu, Mg,
29、Mn, Zn Be, Cl, F Al, Mn or Zn Cast iron Ni, Cu, Fe, Mn Ba, F Ni or Cu Hardfacing Co, Cr, Cr(VI), Fe, Ni, Mn V Co, Cr, Cr(VI) Ni or Mn Work hardening Fe, Mn, Cr Mn Nickel-based Co, Cr, Cr(VI) Fe, Ni, Mn Fe Cr, Cr(VI) or Ni Copper-based Cu, Ni Cu or Ni MIG/MAG/TIG (GMAW/GTAW) 131, 135, 141 Unalloyed a
30、nd low alloy steel b Fe, Mn, Cr, Cr(VI) Ni, Cu Mn, Cr or Cr(VI) d High alloy steel c Cr, Cr(VI), Fe, Mn, Ni Cr, Cr(VI) or Ni Aluminium alloys Al, Mg, Mn, Zn Al, Mn or Zn Nickel-based Co, Cr, Cr(VI), Mn, Ni Fe Cr, Cr(VI) or Ni Copper-based Cu, Ni Cu or Ni Gas-shielded tubular cored arc welding (FCAW)
31、 132, 133, 136, 137, 143 Unalloyed and low alloy steel b Fe, Mn, Cr, Cr(VI) Ni, Cu F Mn, Cr or Cr(VI) High alloy steel c Cr, Cr(VI), Fe, Mn, Ni F Cr(VI) or Ni Hardfacing Co, Cr, Cr(VI), Fe, Ni, Mn V Co, Cr, Cr(VI) Ni or Mn Nickel-based Co, Cr, Cr(VI). Mn. Ni Fe Cr, Cr(VI) or Ni Self-shielded tubular
32、 cored arc welding (FCAW) 114 Unalloyed and low alloy steel b Fe, Mn, Cr, Ni, Cu, Al Ba, F Mn High alloy steel c Cr, Cr(VI), Fe, Mn, Ni, Al Ba, F Cr(VI) or Ni Hardfacing Co, Cr, Cr(VI), Fe, Ni, Mn, Al V Co, Cr, Cr(VI) Ni or Mn aFor welding process numbers, see ISO 4063. bUnalloyed and low alloyed st
33、eels are here considered to have 5 % combined alloying elements. cHigh alloyed steels are here considered to have 5 % combined alloying elements. dFor the unalloyed and low alloyed steels, the Cr(VI) amount can be considered negligible compared to Cr(VI) from high alloyed steels (e.g. Cr(VI) in high
34、 alloyed steels is 36 % and in low alloyed steel 0,05 % in the fume box, see ISO 15011-1). 2 ISO 2014 All rights reservedPD ISO/TR 13392:2014ISO/TR 13392:2014(E) Bibliography 1 ISO 4063, Welding and allied processes Nomenclature of processes and reference numbers 2 ISO 15011-1, Health and safety in
35、welding and allied processes Laboratory method for sampling fume and gases Part 1: Determination of fume emission rate during arc welding and collection of fume for analysis 3 ISO 15011-4, Health and safety in welding and allied processes Laboratory method for sampling fume and gases Part 4: Fume da
36、ta sheets ISO 2014 All rights reserved 3PD ISO/TR 13392:2014ISO/TR 13392:2014(E) ISO 2014 All rights reserved IC S 25.160.01;13.100 Price based on 3 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, in
37、formation and services. BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us We bring together business, industry,
38、 government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes an
39、d across all sectors choose standards to help them achieve their goals. Information on standards We can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Cent
40、re. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organi
41、zations, hard copies can be ordered from our Customer Services team. Subscriptions Our range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to With British Standards Online (BSOL) youll have instant access to ove
42、r 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy an
43、d subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benef
44、its of membership, please visit With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For furthe
45、r information, email . Revisions Our British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication plea
46、se inform the Knowledge Centre. Copyright All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization b
47、odies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording
48、 or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department. Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): Email (enquiries): Subscriptions Tel: +44 845 086 9001 Email: Knowledge Centre Tel: +44 20 8996 7004 Email: Copyright & Licensing Tel: +44 20 8996 7070 Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW
