1、BSI Standards Publication Cutting tool data representation and exchange Part 2: Reference dictionary for the cutting items PD ISO/TS 13399-2:2014National foreword This Published Document is the UK implementation of ISO/TS 13399-2:2014. It supersedes DD ISO/TS 13399-2:2005 which is with- drawn. The U
2、K participation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provision
3、s of a contract. Users are responsible for its correct application. The British Standards Institution 2014. Published by BSI Standards Limited 2014 ISBN 978 0 580 82710 5 ICS 25.100.01; 35.240.50 Compliance with a British Standard cannot confer immunity from legal obligations. This Published Documen
4、t was published under the authority of the Standards Policy and Strategy Committee on 28 February 2014. Amendments/corrigenda issued since publication Date Text affected PUBLISHED DOCUMENT PD ISO/TS 13399-2:2014 ISO 2014 Cutting tool data representation and exchange Part 2: Reference dictionary for
5、the cutting items Reprsentation et change des donnes relatives aux outils coupants Partie 2: Dictionnaire de rfrence pour les lments coupants TECHNICAL SPECIFICATION ISO/TS 13399-2 Second edition 2014-02-15 Reference number ISO/TS 13399-2:2014(E) PD ISO/TS 13399-2:2014 ISO/TS 13399-2:2014(E)ii ISO 2
6、014 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet,
7、 without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Publish
8、ed in Switzerland PD ISO/TS 13399-2:2014 ISO/TS 13399-2:2014(E) ISO 2014 All rights reserved iii Contents Page Foreword iv Introduction vi 1 Scope . 1 2 Normative references 2 3 T erms and definitions . 2 4 Abbreviated terms 5 5 Representation of the ontological concepts as dictionary entries .5 5.1
9、 General . 5 5.2 cutting_item_feature . 5 5.3 cutting_item_type 7 5.4 Reference systems for cutting items 9 6 Properties for cutting item features and cutting item types .10 Annex A (normative) Information object registration .13 Annex B (informative) Classification tables .14 Annex C (informative)
10、Class definitions .16 Annex D (informative) C utting it em pr operty definitions .34 Annex E (informative) Illustrations of properties .79 Annex F (informative) Illustr ations of irr egular insert pr ofiles and pr operties .90 Annex G (informative) Illustrations of reference positions for cutting it
11、ems 99 Bibliography .104 PD ISO/TS 13399-2:2014 ISO/TS 13399-2:2014(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO techn
12、ical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
13、with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria need
14、ed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
15、rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in
16、 this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barrie
17、rs to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 29, Small tools. This second edition cancels and replaces the first edition (ISO/TS 13399-2:2005), which has been technically revised. ISO 13399 consists of the followi
18、ng parts, under the general title Cutting tool data representation and exchange: Part 1: Overview, fundamental principles and general information model Part 2: Reference dictionary for cutting items Technical Specification Part 3: Reference dictionary for tool items Technical Specification Part 4: R
19、eference dictionary for adaptive items Technical Specification Part 5: Reference dictionary for accessory and auxiliary items Technical Specification Part 50 Reference dictionary for reference systems and common concepts Technical Specification Part 60: Reference dictionary for connection systems Te
20、chnical Specification Part 100: Definitions, principles and methods for reference dictionaries Technical Specification Part 150: Usage guidelines Technical Specification Part 301: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of thread cutting taps, th
21、read forming taps and thread cutting dies Technical Specification Part 302: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of solid drills and countersinking tools Technical Specification The following parts are under preparation: Part 51: Designation s
22、ystem for customer solution cutting toolsiv ISO 2014 All rights reserved PD ISO/TS 13399-2:2014 ISO/TS 13399-2:2014(E) Part 80: Concept for the design of 3D models based on properties according to ISO 13399: Overview and principles Technical Specification Part 201: Concept for the design of 3D model
23、s based on properties according to ISO/TS 133992: Modelling of regular inserts Technical Specification Part 202: Concept for the design of 3D models based on properties according to ISO/TS 133992: Modelling of irregular inserts Technical Specification Part 203: Concept for the design of 3D models ba
24、sed on properties according to ISO/TS 133992: Modelling of exchangeable inserts for drilling Technical Specification Part 204: Concept for the design of 3D models based on properties according to ISO/TS 133992: Modelling of inserts for reaming Technical Specification Part 303: Concept for the design
25、 of 3D models based on properties according to ISO/TS 133993: Modelling of end mills with non indexable cutting edges Technical Specification Part 304: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of milling cutters with arbor hole and non indexable c
26、utting edges Technical Specification Part 307: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of end mills for indexable inserts Technical Specification Part 308: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modell
27、ing of milling cutter with arbor hole for indexable inserts Technical Specification Part 309: Concept for the design of 3D models based on properties according to ISO/TS 133993: Tool holders for indexable inserts Technical Specification Part 311: Concept for the design of 3D models based on properti
28、es according to ISO/TS 133993: Modelling of solid reamers Technical Specification Part 312: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of reamers for indexable inserts Technical Specification Part 401: Concept for the design of 3D models based on pr
29、operties according to ISO/TS 133994: Modelling of converting, extending and reducing adaptive items Technical Specification Part 405: Concept for the design of 3D models based on properties according to ISO/TS 133994: Modelling of collets Technical Specification ISO 2014 All rights reserved v PD ISO
30、/TS 13399-2:2014 ISO/TS 13399-2:2014(E) Introduction This part of ISO 13399 defines the terms, properties, and definitions for those portions of a cutting tool that remove material from a workpiece. Cutting items include replaceable inserts, brazed tips, and the cutting portions of solid cutting too
31、ls. The purpose of this part of ISO 13399 is to provide a reference dictionary to support the use of the general information model defined in ISO 13399-1. A cutting tool with defined cutting edges is used on a machine to remove material from a workpiece by a shearing action at the cutting edges of t
32、he tool. Cutting tool data that can be described by ISO 13399 (all parts) include, but are not limited to, everything between the workpiece and the machine tool. Information about inserts (e.g. regular and irregular shaped replaceable cutting items), solid tools (e.g. solid drill and solid endmill),
33、 assembled tools (e.g. boring bars, indexable drills and indexable milling cutters), adaptors (e.g. milling arbor and drilling chuck), components (e.g. shims, screws and clamps) and their relationships can be represented by ISO 13399 (all parts). Possible assemblies of the components of a cutting to
34、ol are illustrated in Figure 1. The objective of ISO 13399 (all parts) is to provide the means to represent the information that describes cutting tools in a computer-sensible form that is independent from any particular computer system. The representation will facilitate the processing and exchange
35、 of cutting tool data within and between different software systems and computer platforms and support the application of this data in manufacturing planning, cutting operations, and the supply of tools. The nature of this description makes it suitable not only for neutral file exchange but also as
36、a basis for implementing and sharing product databases and for archiving. The methods used for these representations are those developed by ISO/TC 184/SC 4 for the representation of product data by using standardized information models and reference dictionaries. An information model is a formal spe
37、cification of types of ideas, facts, and processes which together describe a portion of interest of the real world and which provides an explicit set of interpretation rules. Information is knowledge of ideas, facts, and/or processes. Data are symbols or functions that represent information for proc
38、essing purposes. Data are interpreted to extract information by using rules for how that should be done and a dictionary to define the terms that identify the data. Everyone in a communication process is expected to use the same information model, the same set of explicit rules and the same dictiona
39、ry in order to avoid misunderstanding. If an information model and its dictionary are written in a computer-sensible language, then there is the additional benefit that they can be computer processable. An engineering information model is therefore a specification for data that establishes the meani
40、ng of that data in a particular engineering context. A model has to be developed by formal methods to ensure that it meets the needs of the situation that it represents. An engineering information model defines the information objects that represent the concepts in an engineering application, the at
41、tributes of the objects, their relationships, and the constraints that add further meaning. An information model is an abstract concept that can be used repeatedly for any example of the real-world situation that it represents. An instance of the model is produced when it is populated with the data
42、items and their values that are applicable to a particular example of that situation. This part of ISO 13399 uses the following International Standards developed by ISO/TC 184/SC 4: the EXPRESS language defined in ISO 10303-11 for defining the information model in ISO 13399-1; the file format for da
43、ta exchange derived from the model and defined in ISO 10303-21; the data dictionary defined in the ISO 13584 series. The ISO 13399 series is intended for use by, among others, tool producers and vendors, manufacturers, and developers of manufacturing software. ISO 13399 provides a common structure f
44、or exchanging data about cutting tools with defined cutting edges. ISO 13399 is intended to provide for, or improve, several manufacturing activities, including the integration and sharing of data for cutting tools and assemblies between different stages for the manufacturing cycle and between diffe
45、rent software applications,vi ISO 2014 All rights reserved PD ISO/TS 13399-2:2014 ISO/TS 13399-2:2014(E) the direct import of data from cutting tool suppliers into a customers database, and the management of cutting tool information from multiple sources and for multiple applications. Different comp
46、anies use different business models that determine their need for the communication of information about their products. For example, one cutting tool manufacturer could regrind its customers tools while another could allow its customers to do the regrinding and provide the information to enable the
47、m to do so. Therefore, the two cutting tool manufacturers could have a different set of cutting tool properties to communicate using the information model and dictionaries provided in ISO 13399. ISO 13399 defines only the information that could be communicated, but does not specify what information
48、shall be communicated. Figure 1 Possible assemblies of components of a cutting tool Since the content of those dictionaries evolves according to industrial innovations and constant improvement of technology in cutting tools, a Maintenance Agency has been established for the purposes of correcting er
49、rors in the entries of existing classes and properties, adding new properties to existing classes, adding new classes and their properties, managing the status of those properties and classes, and migrating the dictionary to subsequent editions of ISO 13399 (all parts). The secretariat of this Maintenance Agency has been assigned to:Union de Normalisation de la McaniqueF-92038 Paris La Dfense CEDEXFrance
